System Description; Preparation For Use - 3M 6000 Serie Bedienungsanleitung

O-QX65-MAC10-QX-3800-1063-4_Iss3.qxd
USER INSTRUCTIONS
Please read these instructions in conjunction with the
appropriate 3M™ Filter leaflet or 3M™ Air Supply Unit User Instructions AND
with the 3M™ 6000 Series Face Piece Reference Leaflet where you will find
information on:
• Approved combinations of 3M Filters and/or 3M Air Supply Units
• Spare Parts
• Accessories
FOREWORD
Failure to follow all instructions on the use of this product and/or failure to
wear the respirator system during all times of exposure may adversely
affect the wearer's health, may lead to severe illness or permanent
disability and may render any warrantly null and void.
If you have any doubts about the suitability of the product to your job
situation, it is recommended that you consult an occupational hygienist,
or call 3M TechAssist on 1800 024 464 (AUS), 0800 364 357 (NZ).

SYSTEM DESCRIPTION

When a 3M™ 6000 Series Face Piece is combined with a pair of approved
3M Filters (see Reference Leaflet) it forms a filtering apparatus for respiratory
protection.
Such apparatus is designed to remove potentially harmful gases, vapours and/or
particulates from the surrounding atmosphere.
The 3M™ 6000 Series Face Piece may also be used with the 3M™ Air Supply
Units as specified in the Reference Leaflet.
APPROVALS
These respirators have been produced to comply with the requirements of the
Australian Standard AS/NZS 1716:2003 under an agreed production
certification scheme operated during manufacture in accordance with the SAI
Global StandardsMark programme.
LIMITATIONS TO USE
Use this respirator strictly in accordance with all instructions:
• Contained in this User Instruction and Reference Leaflet.
• Accompanying other components of the system
(e.g. 3M Filters / 3M Air Supply Units).
Only use with the 3M Filters / 3M Air Supply Unit and spares and accessories
listed in the Reference Leaflet and within the usage conditions given in the
Technical Specification.
Only for use by trained, competent personnel.
Leave the contaminated area immediately if:
a) Any part of the system becomes damaged.
7/8/08 15:17
AU NZ
45
Page 45
b) Airflow into the face piece decreases or stops.
c) Breathing becomes difficult or increased breathing resistance occurs.
d) Dizziness or other distress occurs.
e) You taste or smell contaminants or an irritation occurs.
Never modify or alter this product, replace parts only with original 3M parts.
Do not use in oxygen or oxygen-enriched atmospheres.
In case of intended use in explosive atmospheres, contact 3M.
Do not use in concentrations above those specified in Technical Specifications.
Do not use for respiratory protection against unknown atmospheric
contaminants or when concentrations of contaminants are unknown or
immediately dangerous to life or health (IDLH) or in atmospheres containing
less than 19.5% oxygen (3M definition). Individual countries may apply their
own limits on oxygen deficiency. Please seek advice if in doubt.
Only suitable for use by clean-shaven personnel, facial hair under the seal
reduces protection.
If you cannot achieve a proper fit, do not enter the contaminated area. See your
supervisor.
Do not use for escape purposes or with self-contained breathing apparatus.
These products contain no components made from natural rubber latex.
National regulations may impose specific limitations on the use of filters
depending on the filter class and the face piece used.
Use of any 3M Face Piece / Filter combination should be in accordance with
applicable safety & health standards, AS/NZS 1715 or in accordance with the
recommendations of an occupational hygienist.
If using with a 3M™ Air Supply Unit:
• At very high work rates, the pressure in the face piece may become negative at
peak inhalation flow.
Adjust equipment as appropriate or consider an alternative form of respiratory
protective device.
If using in supplied air mode, ensure that:
• The source of the air supply is known.
• The purity of the air supply is known.
• The air supply is of a breathable quality, to AS/NZS 1715.

PREPARATION FOR USE

Inspection
Check apparatus is complete, undamaged and correctly assembled, any damaged
or defective parts must be replaced before use.
The following inspection procedure is suggested:
1. Check the face piece for cracks, tears and dirt. Be certain the face piece,
especially the face seal area, is not distorted. The material must be pliable –
not stiff.
2. Examine the inhalation valves for cracking or tearing. Lift valves and
46