Before Operating - Redmond RMC-M70 Bedienungsanleitung

3. Cooking time indicator.
4. "Preset" timer (1 or 2) indicator.
5. Product type indicator in "ПАР", "ЖАРКА" and "ТУШЕНИЕ" programmes.
6. Subprogramme indicator in "ВАРКА" programme.
7. "МУЛЬТИПОВАР" cooking temperature indicator.
I. BEFORE OPERATING
Carefully unpack the device, remove all packaging materials and stickers except the one with
the unit's serial number.
Keep all warning labels and the serial number identification label located on the housing!
After transportation or storage at low temperatures allow the appliance to stay at room tem-
perature for at least 2 hours before using it.
Wipe all interior and exterior surfaces of the unit with a soft, damp cloth. Wash the bowl in
warm soapy water. Rinse and dry thoroughly. Odor on first use of the appliance is normal. In
such case, clean the device.
Do not switch the device on without the bowl inside or with empty bowl — in case of accidental
start of the cooking program it will lead to the device critical overheating or will damage the
non-stick coating.
II. OPERATION
Before Use
Place the device on a flat, stable, and hard surface away from any objects or cabinets that
could be damaged by steam, humidity, or high temperatures.
Before operating, make sure that the outer and inner parts of the multicooker have no dents,
cracks or any other visible damages. There should not be any obstructions between the heat-
ing element and the bowl.
Setting the Clock
1. Plug in the unit. Press and hold down "Отложенный старт" button until the minute indi-
cator starts blinking.
2. Press "Время приготовления" button repeatedly to set the minutes (setting interval is
1 minute). Hold the button down to scroll through the digits.
3. Press "Установка времени" button, hour indicator starts blinking. Set hours using the
"Время приготовления" button. Hold the button down to scroll through the digits.
4. When you finish entering the data press "Подогрев/Отмена" button or do nothing for a
few seconds to save your settings. Time indicator stops blinking.
16
Setting the Cooking Time
Multicooker REDMOND RMC-M70 allows manually adjusting the cooking time, set by default
for each programme. Setting interval and time adjustment range depend on the programme
chosen.
1. Press "Установка времени" button, minute indicator starts blinking. Press "Время
приготовления" button repeatedly to adjust the minutes. Hold the button down to scroll
through the digits.
2. Press "Установка времени" button, hour indicator starts blinking. Press "Время приготовления"
button repeatedly to adjust the hours. Hold the button down to scroll through the digits.
3. If you need to set the time of less than one hour press and hold down the "Время
приготовления" button until the hour indicator is no longer displayed. Press "Время
приготовления" button repeatedly to set the minutes.
4. To cancel the settings and reset press "Подогрев/Отмена".
For your convenience, the time adjustment range in all programmes starts with the minimum
setting, enabling you to prolong the cooking time if the dish comes out undercooked.
This is a non-volatile memory unit. In case of a short term power cut-off all settings, including
Preset function, will be saved.
"Отложенный старт" ("Time Delay") Function
Time delay function allows programmeming the cooking programme to be over by certain
time. The programme can be delayed for a period of time from 10 minutes to 24 hours with
10 minute intervals. To set the Timer:
1. Select an automatic programme. Adjust the cooking time set by default if necessary.
2. Press "Отложенный старт" button to select ТАЙМЕР 1 (TIMER 1) or ТАЙМЕР 2 (TIMER 2).
3. Press "Установка времени" button to enter the hour setting mode. Hour indicator starts
blinking.
4. Adjust the hours using the "Время приготовления" button (setting interval is 1 hour).
5. Press "Установка времени" button. Minute indicator starts blinking.
6. Adjust the minutes using the "Время приготовления" button (setting interval is 10 min-
utes).
7. When all settings are entered press "Старт" button. "Старт", "Подогрев/Отмена" and
"Отложенный старт" button indicators light up. The time by which your meal will be ready
is displayed.
Setting the Preset function remember that the countdown in some programmes begins only
when the device reaches its operating temperature.
"Автоподогрев" ("Keep warm") Function
Keep warm function is being activated automatically upon the end of the cooking programme.
It allows maintaining the temperature of 70-75°C for a period of time up to 24 hours. "Подогрев/