Bestway Flowclear 58199 Bedienungsanleitung Seite 5

Section II: Hose Configuration for Backwashing and Rinsing (See Fig.11)
D
Fig.11
B
Section III: Backwashing and Rinsing
Backwash and Rinsing must be preformed to prime the pump for it's first use and to wash the sand.
CAUTION: DO NOT DRY RUN THE SAND FILTER
1. Press down on the Control Valve handle and rotate to the Backwash function.
2. Insert the plug into a proper socket and run the sand filter for 3-5 minutes, or until the water runs clear.
3.Unplug the sand filter and set the Control Valve to the Rinse function.
4. Insert the plug and run the sand filter for 1 min. This circulates water backwards through the sand filter and drains water out of Port D.
5. Unplug the sand filter. Set the Control Valve to the Closed function.
6. Top up pool water.
IMPORTANT: This procedure removes water from the pool, which you'll need to replace. Unplug the sand filter immediately if water levels near the
pool's connection valves. DO NOT DRY RUN THE SAND FILTER.
Section IV: Complete Sand Filter Installation
A
Fig.12
B
Sand Filter Operation
1. Now the sand filter is ready for use. Set the Control Valve to the Filter function.
NOTE: To prevent the risk of eletric shock, dry any excessive water from yourself and the
sand filter.
2. Insert the plug into a suitable socket to run the sand filter.
NOTE: The sand filter has now started its filtering cycle. Check that water is returning to the
pool and take note of the filter pressure on Pressure Gauge. (See Fig.13) Generally, the
recommended sand filter pressure is less than 0.055MPa (8PSI) (in green area) when it is
running.
Sand Filter Maintenance
CAUTION: You must ensure the sand filter is unplugged before any maintenance
begins, otherwise severe risk of injury or death may occur.
As dirt builds up in the sand filter, the pressure reading on Pressure Gauge will increase.
(See Fig.14) When the Pressure Gauge is 0.055MPa (8PSI) or higher, or water flow to the
pool is too low, it is time to clean the sand.
To clean the sand bed, follow all instructions outlined previously in Section III:
Backwashing and Rinsing
NOTE: We recommend you clean the sand bed once a month or less regularly depending
on how often the pool is used. Do not clean the sand too frequently.
>1.3cm
B
Pool
A
>1.3cm
B Pool
>2m
NOTE: Ensure the Control Valve is set to the Closed function.
Your pool should be filled with water.
1. Attach one Hose to the sand filter's Port B; screw the threaded
locking ring into position.
2. Connect the other end of the Hose to Port B connection valve;
screw the threaded locking ring into position.
3. Open the connection valve. This allows water to flow to the
sand filter.
NOTE: You can refer to pool manual for connection valve's
installation instructions.
4. Connect the other Hose to Port D and place the opposite end in
drain area.
IMPORTANT: Ensure the Control Valve is set to the Closed
function.
IMPORTANT: Make certain both of the pool's connection valves
are fully submerged by water before operating the sand filter.
Connect the Second Hose (See Fig.12)
NOTE: Ensure the Control Valve is set to the Closed function.
1. Detach the Hose from Port D.
2. Attach the Hose to the Control Valve's Port A; screw the
threaded locking ring into position.
3. Connect the other end of the Hose to the Port A connection
valve; screw the threaded locking ring into position.
4. Open the connection valve. This allows water to flow to the
sand filter.
NOTE: You can refer to pool manual for connection valve's
installation instructions.
5
psi
MPa
Fig.13
psi
MPa
Fig.14
S-S-000719