Use Limitations; Environmental Protection; Intended Use; Improper Use - GGP ITALY MP2 504 Series Gebrauchsanweisung

machine. The use of an unbalanced cutting element,
the excessive speed of movement, or the absence
of maintenance have a significant influence on
noise emissions and vibrations. Consequently, it
is necessary to take preventive steps to eliminate
possible damage due to high levels of noise and stress
from vibration. Maintain the machine well, wear ear
protection devices, and take breaks while working.

Use limitations

• Never operate the machine with guards damaged,
missing or incorrectly assembled (grass catcher,
side discharge guards rear discharge guards)
• Don't use the machine if the attachments/
tools are not installed in their seats.
• Never disengage, deactivate, remove or tamper
with the safety systems/microswitches installed.
• Do not alter the engine adjustments, nor over-run it. If
the engine is forced to work with an excessive number
of rotations, the risk of personal injury increases.
• Do not strain the machine too much and do not
use a small machine for heavy-duty work. If you
use the right machine, you will reduce the risk of
hazards and improve the quality of your work.
2.4 MAINTENANCE, STORAGE AND TRANSPORT
Ensure regular maintenance and correct storage to
maintain machine safety and high performance levels.
Do not use the machine with worn or
damaged parts. Faulty or worn-out parts must
always be replaced and never repaired. Only use
original spare parts: the use of non-original and/
or incorrectly fitted parts will compromise the
safety of the machine, may cause accidents or
personal injuries for which the Manufacturer is
under no circumstance liable or responsible.
Maintenance
• To reduce the risk of fire, regularly check
the machine for oil and/or fuel leaks.
• Be careful during adjustment of the machine to prevent
entrapment of the fingers between moving parts of
the cutting means and fixed parts of the machine.
Storage
• Do not store the machine with fuel in the tank
in an area where fuel vapours could reach a
naked light, a spark or a strong heat source.
• To reduce fire risks, do not leave containers
with debris inside a room.
Handling and Transportation
• When transporting the machine on a vehicle, always:
1. load the machine with the engine switched off
and pushed by an adequate number of people
2. close the fuel tap (if provided)
3. position it so that it can not cause
a hazard for anybody
4. fasten firmly to the means of transport using
ropes or chains to prevent it from tipping
over causing damage and fuel leaks
2.5

ENVIRONMENTAL PROTECTION

Safeguarding the environment must be a relevant
and priority aspect of machine use, of benefit to
the community and the environment we live in.
• Avoid being a disturbance to the neighbourhood.
Use this machine at reasonable times of the
day only (not early morning or late evening
when the noise could cause disturbance).
• Adhere strictly to the local regulations governing the
disposal of packaging, oil, fuel, filters, damaged parts
or any other element which may have an impact on
the environment; this waste should not be disposed
of along with standard household waste, but must
be disposed of separately and sent to special waste
disposal facilities for handling and recycling.
• Scrupulously comply with local regulations
for the disposal of waste materials
• When the machine is withdrawn from service, do not
dump it in the environment, but take it to a waste disposal
facility in accordance with the local regulations in force.
3. GETTING TO KNOW THE MACHINE
3.1 DESCRIPTION OF THE MACHINE
AND PLANNED USE
This machine is pedestrian controlled lawnmower.
The machine is essentially composed of an
engine which drives a cutting means enclosed in
a casing, equipped with wheels and a handle.
The operator is able to operate the machine and use
the main controls, always staying behind the handle
at a safe distance from the rotating cutting means.
If the operator leaves the machine, the engine and
cutting means will stop within a few seconds.
3.1.1

Intended use

This machine was designed and manufactured
for cutting (and collecting) grass in gardens and
grassy areas, in areas in proportion to its cutting
capacity, done by a pedestrian operator.
Generally speaking this machine can:
1. mow the grass and collect it in the grass catcher;
mow the grass and discharge it on the
2.
ground from the rear section;
3. mow the grass and discharge it
from the side (if provided)
4. mow, chop and deposit the grass on the
ground (mulching effect - if provided ).
The use of special attachments provided for by the
Manufacturer as original equipment or which may be
purchased separately, allows this work to be done in
various operating modes, illustrated in this manual or the
instructions that accompany the single attachments.
3.1.2

Improper use

Any other usage not in keeping with the above-
mentioned ones may be hazardous and harm
EN - 3