How To Use The Machine - GGP ITALY DML 504 AVS Gebrauchsanweisung

EN

HOW TO USE THE MACHINE

For instructions regarding the engine and the battery (if sup-
plied), read the relevant manuals.
NOTE - The number which precedes each paragraph links the
references in the text to the respective figures (listed on the pages
2 - 3 - 4 - 5).
1. COMPLETE ASSEMBLY
NOTE - The machine can be supplied with some parts alrea-
dy assembled.
WARNING - Unpacking and completing the assembly should
be done on a flat and stable surface, with enough space for
machine handling and its packaging, always making use of
suitable equipment.
Disposal of the packaging should be done in accordance with
the local regulations in force.
1.1a 1.1b
Type "I" -
Return the handle (1) to the work position and secure it to the side
chassis supports using the supplied nuts and bolts (2) as illus-
trated.
The handle (1) can be height-adjusted in three different positions
by inserting the pins (3) in one of the three pairs of holes on the
brackets.
Tighten the thumb knobs (2) securely after adjustment.
Hook the starter cable (4) to the guide spiral (5 or 5a – if fitted).
Tighten the nut (6-if applicable) to secure the spiral (5 or 5a).
1.1c
Type "III":
Return the handle (1) to the work position and secure it to the side
chassis supports using the supplied nuts and bolts (2) as illus-
trated.
The handle (1) can be height-adjusted in three different positions
by inserting the pins (3) in one of the three pairs of holes on the
brackets.
The washers (4) on the clamps (5) must be mounted so they keep
the handle (1) firmly fixed without too much effort required to
tighten or release them.
Tighten the clamps (5) after adjusting.
Insert the starter cable (6) in the guide spiral (7).
Tighten the nut (8) to secure the spiral (7).
1.2
Insert the chassis (1) in the grass-catcher (2) and secure all
plastic profiles (3) as illustrated using a screwdriver.
1.3
In electric start models, connect the battery cable (1) to
the general wiring connector (2) on the lawnmower.
2. CONTROL DESCRIPTION
NOTE - The meanings of the symbols on controls are
explained on page 6 and following.
2.1
Throttle trigger
The throttle is controlled by the lever (1). Lever positions are indi-
cated on the relevant plate.
Some models have a fixed speed, and therefore no need of a
throttle.
2.2
Blade brake lever
The blade brake is controlled by the lever (1) which must be held
against the handle for ignition and during lawnmower operations.
The engine stops when the lever is released.
2.3
Drive engagement lever
In the power-driven models, the lawnmower is moved forward by
pulling the lever (1) towards the handle.
The lawnmower stops moving forward when the lever is released.
2.4
Cutting height adjustment
MAKE THIS ADJUSTMENT WHEN THE ENGINE IS OFF.
To adjust cutting height, press the button (1) and lift or push the
chassis using the handle (2) to the desired position, indicated by
the numbered scale (3).
2.5
• Only for models DML: Discharge selection lever
This lever (1) has two positions:
Type "II":
«A» = rear discharge without collection or with cut grass in the
grass-catcher.
«B» = "mulching" function or (if applicable) side discharge without
collection.
To switch from one position to the next, slightly lift the lever (1)
and move it to the desired position so it is locked by the stop (2).
NOTE - If switching from one position to the next is difficult, the
problem may be caused by residual grass accumulated in the
sliding guides and, therefore, the chassis interior must be washed
and cleaned ( 4.4).
3. GRASS CUTTING
NOTE - This machine cuts lawns in various modes; before start-
ing work, prepare the machine based on how the lawn is to be
mowed.
• Only for models DML:
3.1a
Preparation for grass cutting and collection in grass-
catcher:
– Move the discharge selection lever (1) to position «A».
– In models with side discharge potential: make sure the side
door (2) is lowered and locked with the safety lever (3).
– Lift the rear stone-guard (4) and correctly hook on the grass-
catcher (5) as shown in the figure.
3.1b
Preparation for grass cutting and rear discharge:
– Move the discharge selection lever (1) to position «A».
– In models with side discharge potential: make sure the side
door (2) is lowered and locked with the safety lever (3).
3.1c
Preparation for grass cutting and mulching:
– Move the discharge selection lever (1) to position «B».
– In models with side discharge potential: make sure the side
door (2) is lowered and locked with the safety lever (3).
3.1d
Preparation for grass cutting and side discharge
(if applicable):
– Move the discharge selection lever (1) to position «B».
– Slightly push the safety lever (3) and lift the side door (2).
– Insert the discharge deflector (6) as shown in the figure.
– Close the side door (2) so that the deflector (6) is locked in
place.
•• Only for models DM:
3.1e
Preparation for grass cutting and collection in grass-
catcher:
– Lift the rear stone-guard (4) and correctly hook on the grass-
catcher (5) as shown in the figure.
3.1f
Preparation for grass cutting and rear discharge:
– Lift the rear stone-guard (4) and remove the grass-catcher (5).
3.1g
Preparation for grass cutting and mulching:
– Lift the rear stone-guard (4) and fit the deflector cap (11) in the
outlet, pushing it until the fastener tooth clicks into place (12).
To remove the deflector cap (11), use the lever (13) located under
the grip, until the tooth (12) is released and the deflector cap is
removed from the outlet.
3.2
Starting the engine
To start, follow the instructions in the engine manual, pull the
blade brake lever (1) against the handle and firmly pull the starter
cable knob (2).
If the model has electric ignition pull the blade brake lever (1)
against the handle and turn the starter key (3).
3.3
Grass cutting
• In case of "mulching": always avoid removing a large quanti-
ty of grass. Never cut more than one third the total grass height
in a single passage! Regulate the forward speed according to
the lawn conditions and the amount of grass removed.
• For side discharge (if applicable): it is best to mow in a direc-
tion where cut grass is not discharged on the grass still to be
cut.
• If there is a grass-catcher with contents indicator device (if
applicable): while working, with the blade in motion, the indi-
cator remains lifted as long as the grass-catcher is able to hold
cut grass; when it lowers, it means that the grass-catcher is full
and must be emptied.
25