Extraordinary Maintenance - GGP ITALY MP2 504 Series Gebrauchsanweisung

7.3 CHECK/TOP-UP ENGINE OIL
To ensure that the machine will function properly
over time, it is highly recommended to change
the engine oil regularly, following the timing
indicated in the engine's Instruction Manual.
The oil can be discharged at a specialised servicing centre,
or by using a syringe to suction the oil out through the filler
spout, bearing in mind you may need to repeat the operation
several times in order to completely empty the tank.
Remember to top-up with oil before using the machine again.
7.3.1 Check/top-up
Procedure:
• Position the machine on a level surface for the check.
• Wipe around the dipstick. Unscrew it and
pull it out. Wipe the dipstick clean.
• Push the dipstick down completely
without screwing it into place.
• Now pull the dipstick up again. Read off the oil level.
• Top up if the level is lower than the "MAX" mark .
Do not overfill as this could cause the engine to
overheat. If the oil level exceeds the "MAX" mark, the
oil must be drained until the correct level is achieved.
7.4 CLEANING
Clean thoroughly following the instructions
below every time it is used.
7.4.1 Cleaning the machine
• Accurately wash the machine with water after each
mowing, remove grass debris and mud accumulated
under the chassis to prevent it from drying and causing
problems the next time the lawnmower is used.
For side and rear discharge: if fitted,
remove the discharge chute.
• Paint on internal chassis parts may come off over
time due to the abrasive action of cut grass; if this
happens, promptly touch-up paint with rust-proof paint
to prevent rusting that could corrode the metal.
• Always make sure the air intakes are free of debris.
• Do not use aggressive liquids to clean the chassis.
• To reduce fire hazards, keep the lawnmower
and, in particular, the engine free of grass,
leaves, or excessive grease.
• If accessing the lower part is necessary, only tilt the
machine on the side indicated in the engine manual,
following the relevant instructions, making sure that
the machine is perfectly stable before performing any
interventions. On side discharge models, remove
the discharge chute (if installed - see 6.1.2.d).
7.4.2 Cleaning the interior
Remove the grass-catcher;
1. Connect the water hose to the specific
attachment (fig. 20.A);
2. Lower the cutting height as far as possible;
3. Always stand behind the lawnmower handle;
4. Start the engine.
7.4.3 Cleaning the grass-catcher
1. Empty the grass catcher;
2. Shake it to remove grass cuttings and soil residue;
3. Wash and rinse it, then place it where it can dry quickly.
7.5 NUTS AND BOLTS
Keep all nuts, bolts and screws tight to be sure
the equipment is in safe working condition.
7.6 BATTERY
The battery is supplied for electric push-button ignition
control models. Read the engine instruction manual
for instructions regarding autonomy, recharging,
reinstating and maintenance of the battery.
8.

EXTRAORDINARY MAINTENANCE

8.1 CUTTING MEANS
A badly sharpened cutting means pulls at the
grass and causes the lawn to turn yellow.
Do not touch the cutting means until
the machine is switched off and the cutting
means is completely stationary.
All work on the cutting means (disassembly,
sharpening, balancing, repairing, reassembly and/
or replacing) are demanding jobs that require special
skills as well as special tools. For safety reasons, these
jobs are best carried out at a Specialised Centre.
Make sure damaged, misshapen or worn
cutting-means are replaced, together with its
own screws in place to preserve balance.
IMPORTANT Always use original cutting means
bearing the code indicated in the "Technical data" table.
Given product evolution, the cutting means listed in the
"Technical Data" table may be replaced in time with others
having similar interchangeable and operating safety features.
8.1.1 Checking the cutting means pin
There is a pin (fig. 21.A) fitted on some versions of the
lawnmower, visible through the hole on the cutting means,
that allows you to check that the cutting means is intact.
• When the pin is visible, the cutting means
is intact and has suffered no damage.
• If the pin is not visible, the cutting means has been
damaged. Contact the authorised service centre
to have the machine checked and repaired.
EN - 9