Standards Of Use - GGP ITALY ES 414 Gebrauchsanweisung

EN

STANDARDS OF USE

For instructions regarding the engine and the battery (if
supplied), read the relevant manuals.
NOTE - The number which precedes each paragraph links the
references in the text to the respective figures (listed on the pa-
ges 2 - 3).
1. COMPLETE ASSEMBLY
NOTE - The machine can be supplied with some parts al-
ready assembled.
WARNING - Unpacking and completing the assembly
should be done on a flat and stable surface, with enough
space for machine handling and its packaging, always
making use of suitable equipment.
Disposal of the packaging should be done in accordance
with the local regulations in force.
1.1a
"I" type handle – without height adjustment
Attach the bottom of the handle (1) to the holes on the side of
the chassis. Secure it using the nuts and bolts supplied (2).
Attach the top of the handle (3) using the knobs (4) and nuts
and bolts supplied.
Fit the cable clamps (5) as shown and secure the control
cables.
Fit the starter rope in the guide spiral (6) and tighten the nut (7).
1.1b
"II" type handle - with height adjustment
Return the bottom of the fitted handle (1) to its working posi-
tion and lock it in place using the bottom knobs (2). Make sure
that the two pins (3) stay inside their holes (4).
Attach the top of the handle (5) using the knobs (6) and nuts
and bolts supplied.
Fit the cable clamps (7) as shown and secure the control
cables.
Fit the starter rope in the guide spiral (8) and tighten the nut (9).
By loosening the knobs (2) the handle can be set at two differ-
ent heights.
1.2a
For a rigid grass-catcher:
Assemble the two parts of the grass-catcher (3) and (4), mak-
ing sure that the hooks are fully locked into place and fasten
them using the screws supplied (5).
1.2b
For a plastic and cloth grass-catcher:
Insert the frame (15) in the grass-catcher (17) and attach the
plastic bars (18) using a screwdriver, as shown in the drawing.
Fit the edge of the cloth (19) right into the groove of the plastic
part (13), starting 5-7 mm from the ends.
1.3
On models with an electric starter, connect the battery
cable to the lawnmower's general cable connection.
2. DESCRIPTION OF CONTROLS
2.1
The throttle (where fitted) is controlled by the lever (1)
and positioned as shown on the relative plate. Some models
have a fixed speed, and therefore no need of a throttle.
2.2
The blade brake is controlled by the lever (1), which
should be held against the handle when starting and using the
lawnmower. The engine stops when the lever is released.
2.3
In the power-driven models, pull the lever (1) towards
the handle for forward movement. The lawn-mower stops mov-
ing forward when the lever is released.
2.4
The cutting height is adjusted using the levers (1).
On some models, remove the brake cover (2) and unscrew the
pin (3) using the wrench (4) provided; fit the wheels into the
required hole (5) and fully tighten the pin (3) using the wrench
(4). The four wheels must be at the same height. MAKE THIS
ADJUSTMENT ONLY WHEN THE BLADE IS STOPPED.
3. GRASS CUTTING
3.1
Lift the stone-guard and attach the grass-catcher (1)
correctly as shown in the drawing.
3.2
To start, follow the instructions in the engine manual,
pull the blade brake lever (1) against the handle and firmly pull
the starter cable knob (2).
If the model has electric ignition pull the blade brake lever (1)
against the handle and turn the starter key (3).
3.3
The lawn will look better if it is always cut to the same
height and in alternate directions.
LAWN CARE RECOMENDATIONS
Each type of grass has different features and may thus require
different ways to care for the lawn; always read the instructions
on seed boxes for mowing height for the growth conditions in
the work area.
Keep in mind that most grass is made up of a stem and one or
more leaves. If leaves are fully cut, the lawn is damaged and
growth is more difficult.
The following indications generally apply:
– too low a cut causes grass tears and uprooting, with a "spot-
ted" aspect;
– in the summer, cutting must be higher to avoid the ground
from drying;
– do not cut wet grass; this could reduce blade efficiency due
to sticky grass and tear the lawn;
– for particularly high grass, initially mow at maximum admit-
ted machine height followed by a second mow after two or
three days.
3.4
When you have finishing mowing, release the brake
lever (1) and disconnect the spark plug cap (2). Remove the
starter key (3) (where fitted). WAIT FOR THE BLADE TO STOP
before carrying out any type of work on the machine.
4. ROUTINE MAINTENANCE
IMPORTANT – Regular, careful maintenance is essential for
keeping the safety level and original performance of the
machine unchanged in time.
Store the lawnmower in a dry place.
1) Wear strong working gloves during any cleaning, mainte-
nance or adjustment operation on the machine.
2) Carefully clean the machines with water after each cut;
remove the grass debris and mud accumulated inside the
chassis to avoid their drying and thus making the next start-
up difficult.
3) The paintwork on the inside of the chassis may peel off in
time due to the abrasive action of the cut grass; in this case,
intervene promptly by touching up the paintwork using a
rustproof paint to prevent the formation of rust that would
lead to corrosion of the metal.
4) Should it be necessary to access the lower part, only tilt the
machine from the side shown in the engine handbook; fol-
lowing the relative instructions.
5) Do not drip petrol onto the plastic parts of the motor or the
machine to prevent damaging them and remove all traces of
25