Additional Safety Warnings - Scheppach CAD115-20Li Original Bedienungsanleitung

Cutting-Off Operations:
• Do not "jam" the cut-off wheel or apply excessive
pressure. Do not attempt to make an excessive
depth of cut. Overstressing the wheel increases the
loading and susceptibility to twisting or binding of
the wheel in the cut and the possibility of kickback
or wheel breakage.
• Do not position your body in line with and behind
the rotating wheel. When the wheel, at the point of
operation, is moving away from your body, the pos-
sible kickback may propel the spinning wheel and
the power tool directly at you.
• When wheel is binding or when interrupting a cut
for any reason, switch off the power tool and hold
the power tool motionless until the wheel comes to
a complete stop. Never attempt to remove the cut-
off wheel from the cut while the wheel is in motion
otherwise kickback may occur. Investigate and take
corrective action to eliminate the cause of wheel
binding.
• Do not restart the cutting operation in the work-
piece. Let the wheel reach full speed and carefully
re-enter the cut. The wheel may bind, walk up or
kickback if the power tool is restarted in the work-
piece.
• Support panels or any oversized workpiece to mini-
mize the risk of wheel pinching and kickback. Large
workpieces tend to sag under their own weight.
• Supports must be placed under the workpiece near
the line of cut and near the edge of the workpiece
on both sides of the wheel.
• Use extra caution when making a "pocket cut" into
existing walls or other blind areas. The protruding
wheel may cut gas or water pipes, electrical wiring
or objects that can cause kickback.
Safety Warnings Specific for Sanding Opera-
tions:
• Do not use excessively oversized sanding disc
paper. Follow manufacturers recommendations,
when selecting sanding paper. Larger sanding pa-
per extending beyond the sanding pad presents a
laceration hazard and may cause snagging, tearing
of the disc or kickback.
Safety Warnings Specific for Wire Brushing Op-
erations:
• Be aware that wire bristles are thrown by the brush
even during ordinary operation. Do not overstress
the wires by applying excessive load to the brush.
The wire bristles can easily penetrate light clothing
and/or skin.
• If the use of a guard is recommended for wire
brushing, do not allow interference of the wire
wheel or brush with the guard. Wire wheel or brush
may expand in diameter due to work load and cen-
trifugal forces.
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

8. Additional Safety Warnings

1. When using depressed centre grinding wheels,
be sure to use only fiberglass-reinforced wheels.
2. Never use Stone Cup type wheels with this grind-
er. This grinder is not designed for these t pes of
wheels and the use of such a product may result
in serious personal injury.
3. Be careful not to damage the spindle, the flange
(especially the installing surface) or the lock nut.
Damage to these parts could result in wheel
breakage.
4. Make sure the wheel is not contacting the work-
piece before the switch is turned on.
5. Before using the tool on an actual workpiece, let
it run for a while. Watch for vibration or wobbling
that could indicate poor installation or a poorly
balanced wheel.
6. Use the specified surface of the wheel to perform
the grinding.
7. Do not leave the tool running. Operate the tool
only when hand-held.
8. Do not touch the workpiece immediately after op-
eration; it may be extremely hot and could burn
your skin.
9. Observe the instructions of the manufacturer for
correct mounting and use of wheels. Handle and
store wheels with care.
10. Do not use separate reducing bushings or adap-
tors to adapt large hole abrasive wheels.
11. Use only flanges specified for this tool.
12. For tools intended to be fitted with threaded hole
wheel, ensure that the thread in the wheel is long
enough to accept the spindle length.
13. Check that the workpiece is properly supported.
14. Pay attention that the wheel continues to rotate
after the tool is switched off.
15. If working place is extremely hot and humid, or
badly polluted by conductive dust, use a shortcir-
cuit breaker (30 mA) to assure operator safety.
16. Do not use the tool on any materials containing
asbestos.
17. When use cut-off wheel, always work with the
dust collecting wheel guard required by domestic
regulation.
18. Cutting discs must not be subjected to any lateral
pressure.
Information on the rechargeable battery
1. The battery pack of the rechargeable device is
not charged when delivered. It is therefore nec-
essary to charge the battery before first com-
missioning.
2. For optimum battery capacity avoid deep dis-
charge cycles! Charge your battery frequently.
3. Store your battery in a cool place, ideally at 15°C
and with at least 40% charge.
21 | GB