System Configuration; Resetting The Mixer To The Factory Settings; Setting The Date And The Time; Changing The Unit Of Measurement For Signal Delay - IMG STAGELINE DELTA-160R Bedienungsanleitung

7 System Configuration

7.1 Resetting the mixer to the factory settings

The mixer can be reset to its factory settings if required� All settings
made by the user will be lost� Therefore, to preserve your own settings,
make a backup of the corresponding scenes to an external USB storage
☞
device ( chapter 5�8) or export all settings (
resetting� After resetting, the exported settings can be imported into
the mixer again�
1) Press the key SETUP (4) to call up the setup menu�
2) Tap the button "Setup" on the left to call up the view for various
system settings (fig� 26)�
3) Under "System", tap the button "Maintenance"� A view with
various system functions will appear�
4) To reset the mixer to the factory settings, tap the button "Factory
Reset"� Confirm the security prompt with "Factory Reset" or cancel
with "Cancel"�
The mixer will switch off and restart with the factory settings�

7.2 Setting the date and the time

A correct time setting is important for the management of scenes�
To set the current time:
1) Press the key SETUP (4) to call up the setup menu�
2) Tap the button "Setup" on the left to call up the view for various
system settings (fig� 26):
3) Under "System", tap the button "Maintenance"� A view with
various system functions will appear�
4) Tap the button "Time Settings"� The view for setting the time will
appear�
5) Make the settings and confirm with "Save"�
6) Press the key BACK (4) to exit the setup maintenance submenu�

7.3 Changing the unit of measurement for signal delay

For signal delay (DELAY), enter either the delay time (ms) or alterna-
tively the distance (m or ft), e� g� the distance between two speakers
or microphones� The delay time will be automatically calculated from
this value (speed of sound: 343 m / s)�
To change the unit of measurement:
1) Press the key SETUP (4) to call up the setup menu�
2) Tap the button "Setup" on the left to call up the view for various
Sample Rate
system settings�
48.0 kHz
3) Under "Delay Unit", tap the corresponding unit (fig� 32)�
44.1 kHz
4) To exit the setup menu, press the key SETUP�
aa3798d700000000
Delay Unit
ms
Fig. 32 Unit of measurement for signal delay
Crossover
BUS8
IN
80.0 Hz
44
☞
chapter 5�8�4) before
Setup
System Version:
Patch
Meter
IP Address:
IP Address:
FX
Brightness
Scenes
Recorder
Monitor
2019/08/23
X
07:50:01
System
Maintenance
Setup Wifi
ft m
Master LR
IN
80.0 Hz
7.4 Changing the sampling rate for the digital outputs
The default sampling rate of 48 kHz for the digital outputs can be
changed to 44�1 kHz�
To change the sampling rate:
1) Press the key SETUP (4) to call up the setup menu�
2) Tap the button "Setup" on the left to call up the view for various
system settings�
3) Under "Sample Rate", tap the corresponding sampling rate
(fig� 33)� A message will appear to inform you that the setting will
only be valid for the digital outputs� Confirm with "Yes"�
4) To exit the setup menu, press the key SETUP�
Information Sample Rate
Apk: V1.6.1
48.0 kHz
1.3.0 -5B 0.662V
44.1 kHz
Serial: 000000000000090c
aa3798d700000000
Fig. 33 Sampling rate
Delay Unit

7.5 Changing the brightness

ms
To change the brightness of the screen:
1) Press the key SETUP (4) to call up the setup menu�
2) Tap the button "Setup" on the left to call up the view for various
Setup
Crossover
BUS 8
system settings�
System Version:
IN IN
80.0 Hz Patch
3) Tap the corresponding brightness level next to "Brightness"
(fig� 34)�
Meter
IP Address:
4) To exit the setup menu, press the key SETUP�
IP Address:
FX
Brightness
Scenes
Fig. 34 Setting the brightness
Recorder
7.6 Key lock
Monitor
A key lock can be activated to prevent unintentional operation� To
activate the key lock, briefly press the key
dark and all other keys will no longer respond� To deactivate the key
lock, press the key
A password can be defined in the submenu "Setup ➾ System
Maintenance" so that the key lock can only be deactivated when this
password has been entered:
1) Press the key SETUP (4) to call up the setup menu�
2) Tap the button "Setup" on the left to call up the view for various
system settings (fig� 26)�
3) Under "System", tap the button "Maintenance"� A view with
various system functions will appear�
4) Activate the option "Password" (ON)� A message will appear warn-
ing you that you will have to enter the password to deactivate
the lock�
5) Use the keyboard appearing on the screen to enter a password
and make sure to remember it!
6) Tap "OK" to confirm or "Cancel"�
7) Press the key BACK (4) to exit the setup maintenance submenu�
2019/08/23
X
07:50:01
System
Maintenance
Setup Wifi
ft m
Information
Master LR
Apk: V1.6.1
1.3.0 -5B 0.662V 80.0 Hz
Serial: 000000000000090c
aa3798d700000000
ms
Crossover
BUS 8
IN
80.0 Hz
once again�
2019/08/23
X
07:50:01
Sample Rate System
48.0 kHz Maintenance
44.1 kHz
Delay Unit
Setup Wifi
ft m
Master LR
IN
80.0 Hz
(6)� The screen will go