5�6�3�2 External Effects; Effect Processor; Inserting An Effect Module - IMG STAGELINE DELTA-160R Bedienungsanleitung

5.6.3.2 External effects
Requirements:
– The bus intended for the effect has been assigned to the analog
output (19) to which the effect unit is connected (
– The output of the effect unit has been connected to a line level input
of the mixer� The input channel has been matched to the output
☞
signal of the effect unit (
– The input channel for the effect signal has been assigned to the
channel to which the effect is to be added, e� g� the sum channel
( ☞ chapter 5�2�1)�
– The input channels whose signals are to be provided with an effect
have been assigned to the specific bus with the setting "Post Fader"
( ☞ chapter 5�2�2)�
1) Use the key BUS 1– 8 (8) to call up the channel overview for the
signal buses� For the time being, adjust an average volume for the
mixed signal fed to the effect unit using the corresponding control
knob (10) for the specific bus� The white bar graph at the bottom
of the channel strip and also the LED ring around the control knob
will indicate the current fader setting�
2) Press the control knob of the bus or tap the corresponding channel
strip to select the bus� The LED underneath the control knob will
light up�
3) Press the key SENDS (8); it will be illuminated� The key IN 1– 8 (8)
will also be illuminated now�
4) Use the control knobs (10) to adjust the signal parts of the inputs
1– 8 for the effect� Press the key IN 9 – 20 to go to the other input
channels and to adjust their signal parts if required�
Note: The setting for picking up the signal is "Post Fader"; therefore, the
signal part adjusted also depends on the setting of the corresponding input
channel fader�
5) To obtain an optimum level for the effect unit, press the key SENDS
again so that only the key Bus 1– 8 will be illuminated� Use the
corresponding control knob to adjust the bus level�
6) To adjust the overall volume for the effect, press the key IN 1– 8
or IN 9 – 20 to select the range for the input channel of the
effect signal� Use the corresponding control knob (10) to adjust
the channel level�

5.7 Effect processor

The mixer features an effect processor� This effect processor offers
eight effect modules which can be inserted as desired into the input
channels, signal buses and the sum channel:
2 × modulation effects
2 × delay effects
2 × reverb effects
2 × graphic equalizers
One module each can be inserted into the analog input channels; two
modules can be inserted into the signal buses and the stereo sum� It
is therefore recommended to insert an effect that is used for a single
input channel directly into this channel� By contrast, effects to be
used for multiple input signals should be inserted into a signal bus
to which these input channels have been assigned� The signal of this
bus will be mixed to the stereo sum together with the input signals
☞
( chapter 5�6�3�1)�
☞
chapter 5�2�4)�
chapter 5�1)�
Mic IN
GEQ 2
48 V REV HPF 48V
EQ

5.7.1 Inserting an effect module

Gain
To insert an effect module into an input channel, call up the view for
GATE COMP
matching the input (tap the topmost section of the corresponding
REV
channel strip)�
Bus 1
0.0 dB
Bus 6 50|50
Modul 1
CH 1
-1 dB PAN
50/50
Modul 2
L&R
SOLO
MUTE
Fig. 20 Inserting an effect
Under "Insert", tap the effect module to be inserted� To remove the
module, tap the module once again�
Note: If this model is already being used at another location, a message will
appear showing the location where it is currently being used� In this case, de-
termine if a change to the new location is to be forced ("Yes") or not ("No")� If
not, select the other module of the same type if required�
To insert effect modules into signal buses or the sum channel and to
configure the effects:
1) Press the key SETUP (4) to call up the setup menu�
2) Tap the button "FX" on the left to call up the view for the effect
processor (fig� 21)�
3) When all settings have been made, press the key SETUP to exit
the setup menu�
Setup
Modul 1
Patch
Modul 2
Meter
FX
Scenes
Modul 1
Recorder
Monitor
Fig. 21 Effect processor
To insert effect modules into a signal bus or the sum channel:
1) Tap  under "Busses"� A list will appear� Select a signal bus or the
sum channel from this list� In both fields on the left of the list, the
modules currently inserted into this channel will appear�
2) To add or change a module, tap the field� The field will have a
yellow frame�
3) Tap a module at the top to select the module to be inserted�
Note: If this model is already being used at another location, a message will
appear showing the location where it is currently being used� In this case,
determine if a change to the new location is to be forced ("Yes") or not ("No")�
If not, select the other module of the same type if required�
4) To remove the effect, tap the field twice�
5) Repeat these steps for other channels or modules if required�
CH1
Delay HPF
IN IN
0.0 ms 16.0 Hz
Insert
Delay 1 Reverb 1 GEQ 1
Delay 2 Reverb 2 GEQ 2
2019/08/23
07:50:01
Delay 1 Reverb 1 GEQ 1
Delay 2 Reverb 2 GEQ 2
Busses
Bus 1
X
X
39