Return Delivery / Storage; Disposal; Protective Clothing; Maintenance And Repair - Wilo RexaLift FIT L Einbau- Und Betriebsanleitung

English
4. Disconnect the connection between the inlet
pipe and the inlet seal, and pull the inlet pipe out
of the seal.
5. Disconnect the connection between the gate
valve and the pressure connection.
6. Disconnect the connection between the ventila-
tion pipe and the ventilation connection, and pull
the pipe up off the connecting piece.
7. Also remove the DN 50 inlet, if there is one.
8. Then disconnect the diaphragm hand pump from
the lifting unit if it is installed.
9. Once all connections have been disconnected,
release the anchoring points of the lifting unit in
the floor
10. Now the lifting unit can be pulled carefully out of
the pipework.
11. Flush through the lifting unit with clean water and
disinfect it
12. Firmly close all connecting pipes, clean and disin-
fect them.
13. Clean the operating space and disinfect it if
necessary.

7.3. Return delivery / storage

Lifting units that are sent back to the factory
must be cleaned to remove impurities and, if they
have been used with fluids that are harmful to
health, they must also be decontaminated.
For shipping, the parts must be packed in tear-
proof plastic bags of sufficient size in such a
manner that they are tightly sealed and leak-
proof. Furthermore, the packaging must protect
the lifting unit from damage during transporta-
tion. If you have any questions, please contact
the manufacturer!
Please also refer to the "Transport and storage"
section for the return delivery and putting into
storage!

7.4. Disposal

7.4.1. Protective clothing

The protective clothing and cleaning cloths must
be disposed of acc. to waste code TA 524 02 and
EC Directive 91/689/EEC, or acc. to local direc-
tives.
7.4.2. Product
Proper disposal of this product avoids damage to
the environment and risks to personal health.
• Use the services of public or private waste dis-
posal companies, or consult them for the disposal
of the product or parts thereof.
• For more information on proper disposal, please
contact your local council or waste disposal office
or the supplier from whom you obtained the
product.

8. Maintenance and repair

For reasons of safety, and thus to guarantee cor-
rect function of the lifting unit, it must always be
maintained by Wilo customer service.
44
The maintenance intervals for lifting units are
determined by EN 12056‑4:
• ¼ year in the case of commercial companies
• ½ year for units in multi-family houses
• 1 year for units in single-family houses
A log must be kept of all maintenance and repair
work, which must be signed by the service em-
ployee and the end-user.
NOTE
We recommend concluding a maintenance
contract for regular maintenance work. Please
contact Wilo customer service for more infor-
mation about this.

9. Troubleshooting and possible solutions

In order to prevent damage or serious injury when
repairing malfunctions on the lifting unit, the
following points must always be observed:
• Only repair a malfunction if qualified personnel
are available for this work, i.e. the individual tasks
must be carried out by trained specialists. For
example, electrical work must be performed by an
electrician.
• Always secure the lifting unit to prevent it re-
starting inadvertently, by disconnecting it from
the electrical mains. Take appropriate precau-
tions.
• Also comply with the installation and operating
instructions provided with the accessories used!
• Unsanctioned modifications to the lifting unit are
made at the operator's own risk and release the
manufacturer from any warranty obligations!

9.1. Overview of possible malfunctions

Fault
Lifting unit does not pump
Volume flow too low
Current consumption too
high
Delivery head too small
Lifting unit runs roughly /
loud noise

9.2. Overview of possible causes and their remedies

1. Inlet or impeller clogged
• Remove deposits from the inlet, reservoir and/
or pump ⇒ Wilo customer service
2. Incorrect direction of rotation
• Exchange 2 phases of the current feed ⇒ Wilo
customer service
3. Wear of inner parts (e.g. impeller, bearing)
• Renew worn parts ⇒ Wilo customer service
4. Operating voltage too low
• Have the mains connection checked ⇒ elec-
trician
5. Running on two phases
MAINTENANCE AND REPAIR
Identifier for cause and
remedy
1, 3, 5, 6, 7, 8, 9, 10, 11, 12,
15, 16, 17
1, 2, 3, 4, 5, 7, 8, 11, 12, 13
1, 2, 3, 4, 5, 7, 13
1, 2, 3, 4, 5, 8, 11, 12, 13, 16
1, 2, 3, 9, 12, 13, 14, 16
WILO SE 01/2014 Ed.05 DIN A4