Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
• Before replacing the top cover of the mains plug ensure that the
cable restraint (3) is holding the outer sheath of the cable firmly and
that the two leads are correctly fixed at the terminals crews.
4
3
WARNING: NEVER use a light socket.
NEVER connect the live (L) or
neutral (N) wires to the earth
pin marked E or
Fitting a Mains Plug to 115 V Units
(U.K. and Ireland Only)
• The plug should be fitted by a competent person. If you are in
doubt, contact an authorized D
electrician.
• The wires are coloured according to the following code:
live = brown
neutral = blue
• Do not connect the blue or brown wire to the earth terminal in the
plug. Connect as follows:
brown to terminal marked 'L'
blue to terminal marked 'N'
• The plug fitted should be comply with BS EN 60309 (BS4343),
16 Amps, earthing contact position 4h.
WARNING: Always ensure that the cable clamp is correctly
and securely fitted to the sheath of the cable.
Using an Extension Cable
If an extension cable is required, use an approved extension cable
suitable for the power input of this tool (see technical data).
The minimum conductor size is 1.5 mm
always unwind the cable completely. Also refer to the table below.
Conductor size (mm
2
)
Cable rating (Amperes)
0.75
1.00
1.50
2.50
4.00
Cable length (m)
7.5
15
Voltage Amperes
Cable rating (Amperes)
115
0 – 2.0
6
6
2.1 – 3.4
6
6
3.5 – 5.0
6
6
5.1 – 7.0
10
10
7.1 – 12.0
15
15
12.1 – 20.0
20
20
230
0 – 2.0
6
6
2.1 – 3.4
6
6
3.5 – 5.0
6
6
5.1 – 7.0
10
10
7.1 – 12.0
15
15
12.1 – 20.0
20
20
Voltage Drops
In rush currents cause short-time voltage drops. Under unfavourable
power supply conditions, other equipment may be affected. If the
1
2
.
WALT repair agent or a qualified
E
2
. When using a cable reel,
6
10
15
20
25
25
30
45
60
6
6
6
10
6
6
6
15
10
15
20
20
15
20
20
25
20
25
25
–
25
–
–
–
6
6
6
6
6
6
6
6
6
6
10
15
10
10
15
15
15
15
20
20
20
20
25
–
system impedance of the power supply is lower than 0.25
disturbances are unlikely to occur.
ASSEMBLY
WARNING: To reduce the risk of injury, turn off tool
and disconnect from power source before attempting to
move it, changing accessories or making any adjustments
accept as written in laser adjustment instructions.
Unpacking (fi g. 1, 2, 4)
1. Remove the saw from the packing material carefully using the
carrying handle (m).
2. Press down the operating handle (a) and pull out the lock down pin
(o), as shown.
3. Gently release the downward pressure and allow the arm to rise to
its full height.
Bench Mounting (fi g. 5)
1. Holes (j) are provided in all four feet to facilitate bench mounting.
Two different sized holes are provided to accommodate different
sizes of bolts. Use either hole; it is not necessary to use both.
Always mount your saw firmly to prevent movement. To enhance
the portability, the tool can be mounted to a piece of 12.5 mm or
thicker plywood which can then be clamped to your work support
or moved to other job sites and reclamped.
2. When mounting your saw to a piece of plywood, make sure that
the mounting screws do not protrude from the bottom of the wood.
The plywood must sit flush on the work support. When clamping
the saw to any work surface, clamp only on the clamping bosses
where the mounting screw holes are located. Clamping at any
other point will interfere with the proper operation of the saw.
3. To prevent binding and inaccuracy, be sure the mounting surface is
not warped or otherwise uneven. If the saw rocks on the surface,
place a thin piece of material under one saw foot until the saw is
firm on the mounting surface.
Mounting the Saw Blade (fi g. 6, 7, 8, 9)
WARNING: To reduce the risk of injury, turn off tool
and disconnect from power source before attempting to
move it, changing accessories or making any adjustments
accept as written in laser adjustment instructions.
Never depress the spindle lock button while the blade is
under power or coasting.
Do not cut ferrous metal (containing iron or steel) or
masonry or fiber cement product with this mitre saw.
1. Depress the head lock up release lever (cc) to release the lower
guard (b), then raise the lower guard as far as possible.
2. Using the Torx bit in the handgrip end of the supplied wrench (i),
loosen the guard bracket screw (kk) sufficiently to allow the angled
corner piece (mm) to pass between the head of the screw and the
guard. This will allow the guard bracket (ll) to be raised enough to
permit access to the blade locking screw (nn).
3. With the lower guard held in the raised position by the guard
bracket screw (kk) depress the spindle lock button (x) with one
hand, then use the supplied blade wrench (i) in the other hand to
loosen the left-hand threaded blade locking screw (nn) by turning
clockwise.
WARNING: To use the spindle lock, press the button as
shown and rotate the spindle by hand until you feel the
lock engage. Continue to hold the lock button in to keep the
spindle from turning.
4. Remove the blade locking screw (nn) and the outside arbor collar
(pp).
5. Install the saw blade (oo) onto the blade adaptor (qq) seated
directly against the inside arbor collar (rr), making sure that the
teeth at the bottom edge of the blade are pointing toward the back
of the saw (away from the operator).
NOTE: For blades with a blade hole of 15.88 mm , the 25.4 mm blade
adaptor (qq) is not used.
6. Replace the outer arbor collar (pp).
E NG L I S H
,
29
Werbung
Inhaltsverzeichnis
