Herunterladen Inhalt Inhalt Diese Seite drucken

Special Safety Advice For Abrading Using Sandpaper; Special Safety Advice For Polishing; Special Safety Advice For Working With Wire Brushes; Device-Specific Safety Instructions For Small Drill Pmgs 12 B2 And Mains Adapter-Pmgs 12 B2 - Parkside PMGS 12 B2 Originalbetriebsanleitung

Modellbau- und gravierset
Vorschau ausblenden Andere Handbücher für PMGS 12 B2:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

General safety advice for electrical power tools
to twist or snag in the cut, making kickback or
disc breakage more likely.
b) Avoid the area in front of or behind
the rotating cutting disc. If the cutting disc
is moving away from you at the point of con-
straint in the workpiece, then, in the event of
a kickback, the electrical power tool and the
rotating disc may be thrown towards you.
c) If the cutting disc jams or you stop
work for a while, switch the device
off and hold it until the disc comes to
a complete stop. Never attempt to
pull the still rotating cutting disc out of
the cut as this could cause kickback.
Determine and rectify the reason for the jamming.
d) Do not switch on the device if the cut-
ting disc is in the workpiece. Allow
the cutting disc to reach full speed be-
fore carefully continuing with the cut.
Otherwise the disc could snag, jump out of the
workpiece or cause a kickback.
e) Support boards or workpieces whilst
cutting to reduce the risk of kickback
caused by a jammed cutting disc. Large
workpieces may bend under their own weight.
The workpiece must be supported to both sides
of the cutting disc and particularly near the
cutting disc and at the workpiece edge.
f) Be particularly careful when pocket
cutting in existing walls or other areas
where you cannot see what you are cut-
ting into. The cutting disc plunged into the surface
could cut through gas or water pipes, electricity
cables or other objects and cause kickback.
Special safety advice for
Q
abrading using sandpaper
Do not use over-sized sanding sheets.
Follow the manufacturer's recommen-
dations for sanding sheet size. Sanding
sheets that project beyond the backing pad
could cause injury in addition to jamming,
tearing of the sheet or kickback.
12 GB/IE
Special safety
Q
advice for polishing
Do not use the polishing bonnet if it
has any loose parts, in particular the
fastening cords. Tuck the fastening cords
away or trim them. Loose fastening cords rotat-
ing with the attachment could catch your fingers
or become trapped in the workpiece.
Special safety advice for
Q
working with wire brushes
a) Bear in mind that wire brushes lose
pieces of wire during normal use. Do
not overload the wires by applying too
much pressure. Flying pieces of wire can very
easily penetrate thin clothing and / or skin.
b) use a guard, if recommended, but make
sure that the wire brush does not come
into contact with the guard. The diameters
of disc brushes and cup brushes can increase
due to contact pressure and centripetal forces.
Device-specific safety
instructions for small drill
PMGS 12 B2 and mains
adapter-PMGS 12 B2-1
When you use the drill /
grinder wear the following
protective equipment: safety glasses
and protective gloves.
CAuTION! The tool continues to rotate
after it has been switched off!
Avoid contact with rapidly rotating
drill / grinder components.
workpiece. Use clamps or a vice to grip the
workpiece firmly. This is much safer than holding
it in your hand.
self by placing your hands near or in
front of the device or the workpiece
surface. A slip can result in injury.
Securely support the
Never support your-

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis