Herunterladen Inhalt Inhalt Diese Seite drucken

General Safety Advice For Electrical Power Tools; Workplace Safety; Electrical Safety - Parkside PMGS 12 C3 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

Modellbau- und gravierset
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 79
Evaluated acceleration, typical:
Hand / arm vibration: 0.817 m / s
Uncertainty K = 1.5 m / s
Note: The vibration level specified in these instruc-
tions was measured in accordance with an EN 60745
standardised measurement process and can be used
to compare equipment. The vibration emission value
specified can also serve as a preliminary assessment
of the exposure.
The vibration level will change according to the
application of the electrical tool and in some cases
may exceed the value specified in these instructions.
Regularly using the electric tool in such a way may
make it easy to underestimate the vibration.
Try to keep the vibration loads
as low as possible. Measures to reduce the vibration
load are, e.g. wearing gloves and limiting the work-
ing time. Wherein all states of operation must be in-
cluded (e.g. times when the power tool is switched
off and times where the power tool is switched on but
running without load).
Mains adapter PMGS 12 C3-1:
INPuT:
Rated voltage:
230 V∼ 50 Hz
OuTPuT:
Nominal voltage:
12 V
Nominal current:
1 A
Protection class:
II /
Protection type:
IP20
Certified acc. to:
EN 61558-1:2006 / A1:2009,
EN 61558-2-6:2009
General safety advice for
electrical power tools
all safety warnings
and all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and / or serious injury.
Keep all the safety advice and instructions
in a safe place for future reference!
Introduction / General safety advice for electrical power tools
2
2
Read
The term "electrical tool" used in the safety advice
refers to electrical tools powered by mains electricity
(by means of a mains lead) and electrical tools pow-
ered by rechargeable batteries (without a mains lead).

1. Workplace safety

a) Keep your working area clean and well
lit. Untidy or poorly lit working areas can lead
to accidents.
b) Do not work with the device in poten-
tially explosive environments in which
there are inflammable liquids, gases or
dusts. Electrical power tools create sparks,
which can ignite dusts or fumes.
c) Keep children and other people away
while you are operating the electrical
tool. Distractions can cause you to lose con-
trol of the device.

2. Electrical safety

a) The mains plug on the power tool (or
on the power supply) must fit the mains
socket. Never modify the plug in any
way. Never use adapter plugs with
earthed power tools. Unmodified plugs
and the correct sockets reduce the risk of elec-
tric shock.
b) Avoid touching earthed surfaces such
as pipes, radiators, ovens and refrig-
erators with any part of your body.
There is an increased risk of electric shock if
your body is earthed.
c) Keep the device away from rain or
moisture. Water entering an electrical device
increases the risk of electric shock.
d) Do not use the mains lead for any pur-
pose for which it was not intended, e.g.
to carry the device, to hang up the de-
vice or to pull the mains plug out of
the mains socket. Keep the mains lead
away from heat, oil, sharp edges or
moving parts of the device. Damaged or
tangled mains leads increase the risk of elec-
tric shock.
GB
7

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis