Commissioning; Troubleshooting - Bartscher Snack Serie Installations-, Gebrauchs- Und Wartungsanleitung

• Identify the speci f c appliance model. The model number is
detailed on the packing and on the appliance data plate.
• The appliance must be installed in a well-ventilated room.
• Do not obstruct any air vents or drains present on the ap-
pliance.
• Do not tamper with appliance components.
• To avoid breakage and damaging the application, check and
clean the f lter regurarly.

12 COMMISSIONING

Following installation, conversion to a dif ferent type of gas or
any maintenance operations, check appliance operation. In the
event of any malfunction, consult the next Paragraph "T rou-
bleshooting".
12.1 ELECTRICAL APPLIANCES
Switch on the appliance observing the following procedure :
• Remove any pans from the cooking zones.
• Ensure the cooking zones are switched off.
• Power-up the appliance by means of the main switch on the
appliance: the green indicator lights f ash once (after which
they must not switch on or f ash)
• Switch on and increase the cooking level of the zones: the
green indicator light for zones must f ash steadily, indicating
the absence of pans.
• Place a pan of water on each cooking zone: the green indica-
tor light remains steadily illuminated.
• Select the maximum power setting: after a few minutes the
fan switches on.
• Check the current values of each phase.

13 TROUBLESHOOTING

FAULT CAUSE
Insuff cient he- Unsuitable pans
ating of cooking
zone
Continuous he- Defective
ating of cooking parts
zone at maxi-
mum power
Cooking zone Defective pot de-
operates without tection sensor
pan. Small metal
items heat up
The appliance Fuses blown or
does not switch interruption
on power supply
The fuses Generator short-
blow when the circuit
appliance is
switched on
The cooking Pan diameter
zone does not smaller
heat 12cm
Defective gene-
rator
If the red and green indicator lights are off:
• Check the fuses
• Power supply main switch disconnected
• Insuff cient voltage or incorrect electric connection of the ap-
pliance
20
CORRECTIVE MEASURE
Use suitable pans
knob Check/replace the part
Replace the generator
Check connections
of
Replace the generator
Use suitable pans
than
Replace the generator
If the red and green indicator lights work:
• Check and count the green indicator light f ashes. Each long
f ash is followed by a certain number of short
number is the code of the malfunction message detailed in
the following table:
ERROR MESSAGE
1 High voltage
2 No power at in-
ductor
3 G e n e r a t o r
overheating
4 Cooking zone
temperature too
high or too low
5 Defective control
unit
6 Internal tempera-
ture too high
7 Cooking zone
temperature sen-
sor malfunction
8 Faulty power sup-
ply
9 External Tempe-
rature
10 Communication
error
11 Initialization error
12 Failure in mains
current
13 Power supply
connection error
f ashes. This
CAUSE CORRECTI-
VE MEASURE
Unsuitable pans, Use suitable
wrong or defecti- pans, check
ve inductor the inductor
Faulty inductor Connect
connection inductor
perly
Air vents blocked, C h e c k / c l e a r
fan not working, the vents, cle-
f lter clogged, an the fan and
faulty temperatu- check fan rota-
re sensor tion, clean the
f lter
Empty pan, de- Remove
fective temperatu- pan, switch off
re sensor the applian-
ce and let the
cooking zone
cool down be-
fore switching
on again
Faulty connection Check
or defective knob n e c t i o n .
parts Check/replace
the part
Air vents blocked, C h e c k / c l e a r
fan not working, the vents, cle-
f lter clogged, an the fan and
faulty temperatu- check fan rota-
re sensor, close tion, clean the
proximity to exter- f lter, remove
nal heat sources the external
heat source
Sensor short- Check/replace
circuit the part
Power supply or Check the po-
synchronization wer supply
failure
Cooking zone Check/repla-
temperature too ce the part
high or too low ,
defective tempe-
rature sensor
LIN or CAN-Bus Disconnect
fault, no con- from power
nection between supply
keypad and gene- check connec-
rator tions
Error during ini- Wait approx.
tialization of har- 30 seconds for
dware the appliance
to reset
Incorrect control Connect
unit connection control unit to
the correct at-
tachment
Failure while me- Check mains
asuring the mains connection
current
Power supply vol- Check
tage too high or power supply
too low connection
the
pro-
the
con-
and
the
the