Using The Induction Hob/Wok; Prolonged Disuse; Instructions For Cleaning; Reminders For Cleaning - Bartscher Snack Serie Installations-, Gebrauchs- Und Wartungsanleitung

• In the event of an appliance fault or malfunction, shut the
gas shut-off valve and/or switch the appliance off at the main
switch installed upline.
• Clean the appliance following the instructions given in Chap-
ter " INSTRUCTIONS FOR CLEANING".
• Do not store f ammable materials in close proximity to the
appliance. FIRE HAZARD.
• Children should be supervised to ensure that they do not
play with the appliance.
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabili-
ties, or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
• Do not obstruct any air vents or drains present on the ap-
pliance.
• Do not tamper with appliance components.
• Do not use the appliance without the f lters.
• Under no circumstances should the induction cooker be
switched on if the glass ceramic hob is cracked or broken.
This could be dangerous.
• With the transmission of heat from pots, the glass ceramic
hob becomes extremely hot and must therefore never be tou-
ched after cooking (risk of burns).
• Do not place metal items ( utensils, knives, etc.) near the
cooking zones since these can heat up very quickly.
• During use, take care when wearing rings, watches and simi-
lar items since these can become extremely hot if too close
to the cooking zone.
• Users must be informed of the potential risks for individuals
f tted with a heart pacemaker or metallic prosthesis.

9 USING THE INDUCTION HOB/WOK

REMINDERS FOR USE
• The appliance is designed for cooking foods contained in
pots and pans.
• Use f at-bottomed pans.On the wok must be use the specif c
pans.
• Do not leave the hotplates switched on with no pan or an
empty pan in place.
• Do not pour cold liquids onto the hot hotplate.
• The induction hob (made of glass ceramic) is ready for use,
no pre-heating is required.
• Do not use multi-layered pots with aluminium core open
along the edge.
• The induction heating system will not function with unsuitable
materials. These are : chrome-nickel stainless steel, alumi-
nium, copper, brass, glass, stoneware.
• Pots with a diameter smaller than approx. 12cm are not de-
tected by the system and the appliance will therefore not
switch on.
• Use pots with a maximum diameter of 28cm for maximum
heating eff ciency.
• Do not leave the hotplates switched on with no pan or an
empty pan in place.
• Take care when moving pots on the hob. Dropping items on
the glass ceramic hob may cause irreparable damage.
• Position pots in the centre of cooking zones .
• Only use pots and pans speci f cally designed for induction
cookers and beware of those which are very cheap.
SWITCHING ON AND OFF
The control knob for switching on the radiant hotplates has the
following positions:
0 Off
1 Minimum temperature
2 ÷5 Intermediate temperatures
6 Minimum temperatures

10 PROLONGED DISUSE

Before any prolonged disuse of the appliance, proceed as fol-
lows:
• Clean the appliance thoroughly.
• Rub stainless steel surfaces with a cloth soaked in V aseline
oil to create a protective f lm.
• Leave lids open.
• Shut off taps and main switches upline of appliances.
Following prolonged disuse, proceed as follows:
• Inspect the appliance thoroughly before using it again.
• Allow electric appliances to operate at the lowest temperatu-
re for at least 60 minutes.

INSTRUCTIONS FOR CLEANING

REMINDERS FOR CLEANING

The manufacturer will not be liable for any damage or in-
jury resulting from failure to observe the following rules
• Disconnect the appliance electric supply , if present, before
carrying out any operation.
• Clean the satin f nish stainless steel exterior surfaces, the
cooking wells and the surface of the hotplates every day.
• At least twice a year, have an authorized technician clean the
internal parts of the appliance.
• Do not use direct or high pressure water jets to clean the
appliance.
• Do not use corrosive products to clean the f oor beneath the
appliance.
SATIN FINISH STAINLESS STEEL SURFACES
• Clean the surfaces with a cloth or sponge using water and
proprietary non-abrasive detergents. Follow the direction of
the satin f nish lines. Rinse repeatedly and dry thoroughly.
• Do not use pan scourers or other iron items.
• Do not use chemical products containing chlorine.
• Do not use sharp objects which might scratch and damage
the surfaces.
11 FILTERS
AIR FILTERS
• To avoid breakage and damaging the application, check and
clean the f lter regurarly.The f lter is outside the appliance.
• To clean the f lter remove it from its seat: if the f lter is greasy,
wash it with a degreasing soap, rinse and dry. When the pro-
cedure is concluded ref t the f lter in its seat. When the f lter is
deteriorated it must be renewed.

INSTRUCTIONS FOR MAINTENANCE

REMINDERS FOR THE MAINTENANCE TECHNICIAN

The manufacturer will not be liable for any damage or in-
jury resulting from failure to observe the following rules
• Read this manual carefully. It provides important information
for safe installation, use and maintenance of the appliance.
• Installation, conversion to a dif f erent type of gas and applian-
ce maintenance must be carried out by quali f ed technicians
authorized by the manufacturer , in compliance with current
safety standards and the instructions in this manual.
19