Spa Maintenance - Jacuzzi J-300 series Montageanweisung Und Bedienung Und Wartung

I
Programming the Lock Modes
◄ ◄ ◄
Press Press
PRESS PRESS
▲
To activate and deactivate the lock modes, follow the steps below:
A. Press the Menu (
Menu. The LED screen will display "LOC. "
B. Press the Warmer (
LED screen will display the current status of the Lock Mode set-
ting, either L1, L2, L3 or OFF.
C. Press the Warmer (
D. Once the new setting appears of the display, press the Jets
Jets 1 ( ) button to confirm your selection. The display of the
LED screen will blink twice to indicate that the change has been
accepted. You must press the Jets 1 (
our selection or the current settings will remain active.
Note: If no button is pressed within 5 seconds of each selec-
tion the screen will revert back to the Main Menu and the cur-
rent settings will remain active.
I
Top Menu Lock
To prevent unauthorized use of the menu features, you can lock
the Menu access button. When the lock feature is activated, ac-
cess to the Primary Filtration, Secondary Filtration, CLEAR-
RAY, Economy and Lock programming menus is deactivated.
The temperature setting feature, jets pumps operation and light-
ing features are still accessible.
I
Programming the Top Menu Lock Feature
To activate the Top Menu locking feature, follow the steps be-
low:
A. Press and hold the Menu (
B. The LED screen will display "LOC. " The LOC display will al-
so blink twice to indicate that the change has been accepted.
C. When done the LED display will return to the temperature
display.
D. When the LOC feature is active, any time you press the
Menu ( ) button, the LED will display "LOC. "
To deactivate the Top Menu locking feature, follow the steps below:
A. Press and hold the Menu (
B. The LED screen will display "LOC. " The LOC display will al-
so blink twice to indicate that the change has been accepted.
C. You will now have access to the Menus.
◄ ◄ ◄
Press Press
PRESS PRESS
OR
OR
Press
PRESS
OR OR
OR
OR
) button five times to display the Lock
) button to enter the menu. The
) button to scroll through the modes.
) button to confirm y-
) button for 10 seconds.
) button for 10 seconds.

Spa maintenance

◄
Proper and regular maintenance of your spa will help it retain
Press
PRESS
its beauty and performance.
►
I
Cleaning the filters
Your Jacuzzi ®
two high-performance pleated filter cartridges located under
the filter cover.
The circulation pump drawing water through the skimmer bag
and filter cartridge filters fine debris. Large debris is filtered by
jets pump 1 drawing water through the skimmer bag and sec-
ond filter cartridge during an automated skimming/heating cy-
cle or when jets pump 1 is manually acrivated during spa use.
Combined, both filters provide unsurpassed water quality by
trapping surface oils and suspendend particles.
Dispenser for water sanitation
At authorized Jacuzzi dealers, you can purchase a dispenser
where you can place products for water sanitation).
This dispenser must be placed in the filtering cartridge (rec-
ognizable by the grille cover on the compartment) connected
to the circulation pump.
The dispenser must always be removed (while wearing latex
gloves) along with its cover during cleaning of the filter, and
is to be reinstalled when this operation is complete.
ALWAYS TURN POWER TO SPA BEFORE CLEANING
THE FILTER CARTRIDGES!
Refer to the filter cleaning/replacement procedure below:
B
A. Turn off power to spa.
B. Lift cover approx. 3/8" to unclip, then tilt forward to access
filter cartridges
C. Remove skimmer bag from clips, clean out, then clean out debris.
D. Rotate each filter cartridge handle counter clockwise to un-
thread from mating wall fitting.
30
Premium spa is equipped with a skimmer bag and
C
(Filter Cover Back View)
D