Jacuzzi J-300 series Montageanweisung Und Bedienung Und Wartung Seite 28

A. (For Models J385)
Two minutes after power is applied to the spa, an automatic pri-
mary filtration cycles begins. The circulation pump is activated
and set to run for 8 hours a day (factory default). The circula-
tion pump draws water through the skimmer bag and one of t-
wo filter cartridges to effectively remove small debris in your s-
pa. During the primary filtration cycle, the circulation pump and
CLEARRAY are activated. The factory default setting is PF2.
This setting is programmable.
Note: The circulation pump also supplies heated water to the
spa when the heater turns on. Any time the circulation pump
runs outside of a programmed cycle (except for PF0 and PF6),
that run time will reduce the length of the next cycle.
To remove larger debris missed by the primary filtration system,
the control system can activate a secondary filtration system.
These cycles utilize Jets Pump 1 and the second filter cartridge
to quickly "skim" the water of large debris and minimize their
"bath-tub ring" effect.
B. For Models J315
Your new spa includes a 24-hour primary filtration system, which
filters the water continuously (factory default). The circulation
pump draws water through the skimmer bag and one of the t-
wo filter cartridges to effectively remove small debris in your s-
pa. The factory default setting is PF6. This setting should not be
altered. Running the circulation pump less than the factory rec-
ommended time will result in issues with water quality mainte-
nance.
Note: The 24-hour primary filtration system also supplies
heated water to the spa when the heater turns on.
To remove larger debris missed by the 24-hour primary filtration
system, you can program a secondary filtration system. The sec-
ondary filtration cycles use Jets Pump 1 and the second filter
cartridge to quickly "skim" the water of large debris and minimize
their "bath-tub ring" effect.
I
Programming the Primary Filtration Cycle
To make changes to the primary filtration cycle, follow the steps
below.
Press Press
PRESS PRESS
◄ ◄
PRESS PRESS
Press Press
A. Press the Menu (
settings. The LED screen will display "PF. "
B. Press the Warmer (
the system for changes. The LED will display the last cycle pro-
grammed and will blink once to indicate the system is ready to
accept changes.
C. Press the Warmer (
through the cycles, PF0 to PF8.
Press Press Press
PRESS PRESS PRESS
◄ ◄
◄
PRESS PRESS PRESS
Press Press Press
) Button once to access the program
) or Cooler ( ) button to prepare
) or Cooler ( ) button to scroll
D. Once a cycle is selected, press the Jets Pump 1 (
ton to confirm the selection. You must press the Jets Pump 1
( ) button to confirm your selection or the current settings
will remain active.
E. The display will show the new cycle selected and it will blink
twice to indicate that the change has been accepted.
Note: If no button is pressed within 5 seconds of each se-
lection the screen will revert back to the Main Menu and the
current settings will remain active.
I
Programming the Change Filter Timer
Included within the Primary Filtration Menu, is the Change
Filter feature. To make changes to the change filter timer or to
reset it, follow the steps below.
Press
PRESS
A. Press the Menu (
Filtration Menu. The LED screen will display "PF. "
B. Press the Warmer (
mary Filtration cycles. After the last cycle, "PF8, " the LED screen
will display the number of days remaining or zero.
Note: If you press the Warmer button after the number of days
remaining you will revert back to the "PF" menu. You will need
to repeat step B to re-enter the menu.
C. Press the Jets 1 (
Timer. The display on the LED screen will blink once to indicate
that the system is ready to accept changes.
D. Pressing the Warmer (
add or subtract days in increments of 10 days. The range is
from 0 to 180 days.
E. Once you select the number of days, press the Jets 1 (
button to confirm the selection. The display of the LED screen will
blink twice to indicate that the changes have been accepted. You
must press the Jets 1 (
the current settings will remain active.
F. When the countdown timer reaches "0, " the LED display will
flash between "CF" and the water temperature. At this time the
filters must be replaced or cleaned and the timer reset.
Note: If no button is pressed within 5 seconds of each selection
the screen will revert back to the Main Menu and the current set-
tings will remain active.
I
Secondary Filtration Menu
The jets pump 1 activates during the secondary filtration to
provide additional skimming. The spa is programmed with a
default setting of SF0 but can be programmed to any of the cy-
cle settings listed below. These cycles schedule the jets pump
1 to run for a preset amount of time per day, in addition to nor-
mal operation.
Note: During the secondary filtration the jets pump 1, circu-
lation pump and CLEARRAY are activated.
28
Press
PRESS
Press
PRESS
OR
OR
) button once to enter the Primary
) button to scroll through the Pri-
) button to access the Change Filter
) or Cooler ( ) button will
) button to confirm your selection or
) but-
)