Jacuzzi J-300 series Montageanweisung Und Bedienung Und Wartung Seite 29

No filtration
10 minutes of filtration every 12 hrs
10 minutes of filtration every 8 hrs
10 minutes of filtration every 6 hrs
I
Programming the Secondary Filtration Cycle
To make changes to the Secondary Filter Cycle, follow the
steps below.
Press Press
PRESS PRESS
A. Press the Menu (
ondary Filtration Cycle Menu. The LED screen will display "SF. "
B. Press the Warmer (
changes. The LED will display the last cycle programmed and
will blink once to indicate the system is ready to accept
changes.
C. Press the Warmer (
through the cycles, SF0 to SF3.
D. Once a cycle is selected, press the Jets 1 (
button to confirm the selection. You must press the Jets
1 ( ) button to confirm your selection or the current
settings will remain active.
E. The display will show the new cycle selected and it will
blink twice to indicate that the change has been accepted.
Note: If no button is pressed within 5 seconds of each se-
lection the screen will revert back to the Main Menu and the
current settings will remain active.
I
Economy Menu
In Economy mode, the heater only activates after a Secondary
Filtration cycle has finished. The heater will run for a maximum
of 30 minutes. The heater can turn off prior to the 30 minutes
if the programmed water temperature is reached. The Sec-
ondary Filtration program determines the number of cycles
(from 1 to 4) that the heater will be allowed to activate. For ex-
ample, if you have programmed the SF3 setting (10 minutes of
filtration every 6 hours), then the heater will run, for a maximum
of 30 minutes, after the end of each of the 10-minute second-
ary filtration cycle, for up to four times per day. Reference the
chart that follows.
CYCLE RUN TIME
No filtration
10 minutes of filtration
every 12 hrs
10 minutes of filtration
every 8 hrs
10 minutes of filtration
every 6 hrs
Press
PRESS
Press
PRESS
OR
OR
Will return to Will return to
"SF" menu
"SF" menu
) button twice to display the Sec-
) button to prepare the system for
) or Cooler ( ) button to scroll
HEATER RUN TIME
Maximum of a half hour per day
Maximum of a half hour every 12 hrs
(after secondary cycle ends)
Maximum of a half hour every 8 hrs
(after secondary cycle ends)
Maximum of a half hour every 6 hrs
(after secondary cycle ends)
I
Programming the Economy Mode
To activate the Economy Mode, follow the steps below.
◄
Press
▲
PRESS
Press
PRESS
OR
OR
A. Press the Menu (
conomy Menu. The LED screen will display "ECO. "
B. Press the Warmer (
LED screen will display the current status of the Economy
Mode setting, either ON or OFF.
C. Press the Warmer (
tings.
D. Once the new setting appears of the display, press the Jets
Jets 1 ( ) button to confirm your selection. The display of
the LED screen will blink twice to indicate that the change has
been accepted. You must press the Jets 1 (
firm your selection or the current settings will remain active.
Note: If no button is pressed within 5 seconds of each se-
lection the screen will revert back to the Main Menu and the
current settings will remain active.
)
I
Lock Menu
The Lock menu gives you the option to lock specific features
of the spa. There are three locking modes, L1, L2 and L3.
Note: When a lock mode is active, the LED display will flash be-
tween the lock mode and temperature.
L1 lock mode: The jets pumps and heater are deactivated. This
mode can be used when replacing or cleaning the spa filters.
Note: The spa should not be left in this lock mode for an ex-
tended period of time. Especially in colder climate or when
freezing conditions exist.
L2 lock mode: The jets pumps, adjust temperature and
CLEARRAY buttons are deactivated. This mode can be used
to prevent unauthorized use of the spa.
L3 lock mode: The temperature and CLEARRAY buttons are
deactivated. This mode can be used to prevent unauthorized
temperature adjustments.
29
◄ ◄
Press Press
PRESS PRESS
) button four times to display the E-
) button to enter the menu. The
) button to scroll through the set-
) button to con-
◄
▼
►