Ravelli HR 160 SNELLA PLUS Bedienungs- Und Wartungshandbuch Seite 72

Thermo-kaminöfen

Inhaltsverzeichnis

Verfügbare Sprachen

Rev.1 26/03/2018

Pag.72

PHASE

FINAL CLEANING

SWITCH ON

WAITING FOR FLAME

FLAME PRESENT

WORKING

Air/water MODULATION

ECO STOP

T ON / T OFF

FAN WAITING START

FAN WAITING

RE-START

FAN WAITING

RE-START

WAITING SWITCH ON

RE-START

WAITING SWITCH ON

RE-START

HOT SMOKE

Water STAND-BY

OFF

Switching on or Waiting

Flame

Switching on or Waiting

PELLETS FINISHED

Flame

PELLETS FINISHED

EXCESS LOAD

! IMPORTANT

9. Description of alarms

Description of alarms

9. Description of alarms

SIGNALLING

• The pellet tank is empty

ALARM 06

• The gear motor is not loading pellets

PELLETS

USED UP

• Not enough pellets loaded

• No voltage during working

ALARM 01

phase

BLACK - OUT

• The pellet tank is empty

ALARM 05

• Pellet calibration and suction

in switch on phase inadequate

SWITCH ON

• The switch on resistor is

faulty or not in position.

• The pellet tank is empty

ALARM 11

FLAME

• Pellet calibration and suction

ANOMALY

in switch on phase inadequate

ALARM 12 RO-

• The smoke extractor rotations have an

TATION ANOMALY

efficiency loss of 15% due

OF EXTRACTOR

to fan obstruction

• Smoke extractor encoder not working or not properly

connected

ALARM 04

• No power to smoke

EXTRACTOR

extractor

• The smoke extractor is blocked

• The combustion chamber is dirty

ALARM 08

DEPRESSION

• The flue is blocked

• The vacuum meter is malfunctioning

menus

• P1 - P4 multi-function

menus

• P1 displays the temperature

Use and maintenance manual

Fig.37

• P1 displays the temperature

Fig.37

• P4 display power

DESCRIPTION

The stove is in the switch off phase and the cooling phase has not terminated

The spark plug pre-heating phase has started and the pellets start to fall into the grate

The pellets ignite and take advantage of the heat in the intake air that passes through the incande-

scent resistor duct

The pellets ignite and take advantage of the heat in the intake air that passes through the incande-

scent resistor duct

The flame is visible in the grate

The stove has terminated the switching on phase: it is possible to change the working power

The set room temperature/set boiler water temperature has been reached.

Comfort Climate activated, set room temperature reached (air) or the set boiler water temperature has

been reached (water). The stove is off

Comfort Climate activated, set room temperature reached (air) or the set boiler water temperature has

been reached (water). The stove is off

The room probe was shut off or an external thermostat was connected

The stove is in the cooling phase: having reached this condition, it starts automatically

The stove is in the cooling phase: having reached this condition, it automatically re-starts

The phase has activated for hot re-start. Functioning is similar to the SWITCH ON phase

The maximum threshold was reached: to cool, the stove goes to minimum until there is less smoke

The water temperature has reached 85 °C. The stove passes automatically to

STAND-BY mode to guarantee protection of the hydraulic circuit.

The water temperature has reached 85 °C. The stove passes automatically to

STAND-BY mode to guarantee protection of the hydraulic circuit.

The stove is off

When the request to switch on in ECO-STOP status overlaps with a condition of

automatic switch off (using the TIMER), the stove switches on to ensure total cleaning of the

When the request to switch on in ECO-STOP status overlaps with a condition of

basket before passing to FINAL CLEANING

automatic switch off (using the TIMER), the stove switches on to ensure total cleaning of the

basket before passing to FINAL CLEANING

When the pellet setting (set pellets +5) is near the continuous load condition.

IF THE "HOT SMOKE" SIGNAL IS DISPLAYED, IT MEANS THERE ARE

COMBUSTION PROBLEMS. YOU MUST CONTACT YOUR LOCAL TECHNICAL SUPPORT

IF THE "HOT SMOKE" SIGNAL IS DISPLAYED, IT MEANS THERE ARE

CENTRE FOR AN INSPECTION.

COMBUSTION PROBLEMS. YOU MUST CONTACT YOUR LOCAL TECHNICAL SUPPORT

CENTRE FOR AN INSPECTION.

User and Maintenance Manual HYDRO models

Unscrew the protection plug and press

the button to reset the thermostat.

Unscrew the protection plug and press

the button to reset the thermostat.

REASON

: enables scrolling through the icons in the various

and changes.

: enables setting the value of the

HR 160 SNELLA PLUS

desired room temperature

: enables setting the value of the

from "EXT" to "MAN".

desired room temperature

: enables power regulation from Min to Max.

from "EXT" to "MAN".

: enables power regulation from Min to Max.

Example of alarm and solution method.

THERMAL SAFETY ALARM

Example of alarm and solution method.

THERMAL SAFETY ALARM

Fig.38

SOLUTION

• Check there are pellets inside the tank

• Empty the tank and check nothing fell in

that could block the correct functioning

of the screw

• Regulate the pellet setting

• If the problem persists, contact your local Technical Support Centre.

• Press the switch off key and switch on

stove again

• If the problem persists, contact your local technical support centre

• Check there are pellets inside the tank

• Contact your local Technical Support Centre

• Check there are pellets inside the tank

• Contact your local Technical Support Centre

• Carry out as indicated in the specific cleaning booklet

for the stove

• Check the flue is free and clean

• Contact your local Technical Support Centre

15/06/11

Page 28

Inhaltsverzeichnis

Kapitel

Inhaltsverzeichnis

Ravelli HR 160 SNELLA PLUS Bedienungs- Und Wartungshandbuch Seite 72

Kapitel

Fehlerbehebung

Verwandte Produkte für Ravelli HR 160 SNELLA PLUS

Ravelli HR 160 SNELLA PLUS Bedienungs- Und Wartungshandbuch Seite 72

Verfügbare Sprachen

Kapitel

Fehlerbehebung

Verwandte Anleitungen für Ravelli HR 160 SNELLA PLUS

Verwandte Produkte für Ravelli HR 160 SNELLA PLUS

Inhaltsverzeichnis