Recall Function; Count Target Alarm; Preset The Target Zone - Mettler Toledo xpress XTC Bedienungsanleitung

16

RECALL FUNCTION

The XTC can subtract some data via the key
Weight Data
3 0 0 0 00 0 2 0 0
u u u
>0< lb kg g Net CN APW B/G T
Weight Data
3 0 0 0 3 5 0 0 0
u u u
>0< lb kg g Net CN APW B/G T
Weight Data
3 0 0 0 0 5 0 0 0
u u u
>0< lb kg g Net CN APW B/G T
Weight Data
3 0 0 0 0 0 0 0 0
u u
>0< lb kg g Net CN APW B/G T
Weight Data
3 0 0 0 9 9 9 5
u u
>0< lb kg g Net ID APW B/G T
Weight Data
3 0 0 0
u u u
>0< lb kg g Net CN APW B/G T
Weight Data
3 0 0 0 00 0 2 0 0
u u u
>0< lb kg g Net CN APW B/G T

COUNT TARGET ALARM

A target zone (>/<) can be preset via keyboard. If the target alarm is enabled in the Setup Mode, the
scale will beep continually when the piece count is within or outside of this range depending on the soft
switch setting. If the target zone has been preset, the under cursor "< " will be lit when the piece count is
below the Under value. When the piece count is above the Over value, the over cursor ">" will be lit. If
both, the Over and Under values are 0, the target alarm will be disabled.

PRESET THE TARGET ZONE

Weight Data
u n d E r ?
>0< lb kg g Net CN APW B/G T
Weight Data
u n d E r ?
>0< lb kg g Net CN APW B/G T
Weight Data
O U E r ?
>0< lb kg g Net CN APW B/G T
Weight Data
O U E r ?
>0< lb kg g Net CN APW B/G T
Weight Data
3 0 0 0 00 0 2 0 0
u u u
>0< lb kg g Net CN APW B/G T
Note: Both Over and Under values equal to 0 will disable the Target Alarm function.
Count
1 5 0 0
u
M < > PCS
PT %Accy
Count
1 5 0 0
u
PT %Accy M < > PCS
Count
1 5 0 0
u
PT %Accy M < > PCS
Count
1 5 0 0
u u
M < > PCS
PT %Accy
Count
1 5 0 0
u u
PT %Accy M < > PCS
Count
8 1 5 0 0
u
M < > PCS
PT %Accy
Count
1 5 0 0
u
M < > PCS
PT %Accy
Count
1 2 0 0
u u
M < > PCS
PT %Accy
Count
1 8 0 0
u u
M < > PCS
PT %Accy
Count
1 2 5 0
u u
M < > PCS
PT %Accy
Count
1 8 3 0
u u
PT %Accy M < > PCS
Count
1 5 0 0
u u
PT %Accy M < > PCS
. The default data is APW when the scale powers up.
The scale is in the count or weight mode. (Weight window
shows the weight value.)
Press the key . The B/G cursor will light and the Data
window will display gross weight (e.g. 3.5 lb).
Press the key and the T cursor will light. If the current tare
is a push-button tare, the Data display will show the tare
value. If the tare is a keyboard tare or no tare exists, it will
be 0.0000.
Press the key and the PT cursor will light. The Data
display will show the tare that was input via the keyboard. If
the tare is a push-button tare or no tare exists, it will show
0.0000.
Press the key , the %Accy cursor is lit, the Data display
will show the counting accuracy percentage.
Press the key , the ID cursor is lit, the Data display will
show the value of the item No..
Press the key and the APW cursor will light. The Data
display will show the APW.
In count or weight mode, press and hold the key
about three seconds, then release the key. The scale will
enter into target zone setting mode.
Press the key to accept the displayed value, or enter a
new value and then press
After entering the Under value, the display will show prompts
as the illustrated.
Press the key to accept the displayed value, or enter a
new value and then press
After entering the Over value, the scale will return to the
previous mode automatically.
STANDARD COUNTING SCALE
to accept it.
to accept it.
for