Midi Data Format - Yamaha PLG150-AP Bedienungsanleitung

MIDI Data Format

1. Channel messages
1.1 Note on/note off
These messages convey keyboard performance data.
Range of note numbers received = C-2...G8
Velocity range = 1...127 (Velocity is received only for note-on)
When the Multi Part parameter "Rcv NOTE MESSAGE" = OFF, that part will
not receive these messages.
1.2 Control changes
These messages convey control operation information for volume or pan etc.
Their functions are differentiated by the control number (Ctrl#).
If the Multi Part parameter Rcv CONTROL CHANGE = OFF, that part will not
receive control changes.
1.2.1 Bank Select
This message selects the voice bank.
Control# Parameter
0 Bank Select MSB
32 Bank Select LSB
The Bank Select data will be processed only after a Program Change is received,
and then voice bank will change at that time. If you wish to change the voice
bank as well as the voice, you must transmit Bank Select and Program Change
messages as a set, in the following order: Bank Select MSB, LSB, and Program
Change.
1.2.2 Modulation
This message is used primarily to control the depth of vibrato, but the depth of
the following 6 types of effect can be controlled. The effect of this message can
be changed by the following parameters.
* Multi Part Parameter
l. MW PITCH CONTROL
2. MW FILTER CONTROL
3. MW AMPLITUDE CONTROL
4. MW LFO PMOD DEPTH
5. MW LFO FMOD DEPTH
6. MW LFO AMOD DEPTH
By default, an LFO Pitch Modulation (PMOD) effect will apply.
Control# Parameter
1 Modulation
If the Multi Part parameter Rcv MODULATION = OFF, that part will not receive
Modulation.
1.2.3 Portamento Time
This message controls the degree of Portamento (see 1.2.9).
Control# Parameter
5 Portamento Time
When Portamento is ON, this regulates the speed of the pitch change. A value of
0 is the shortest Portamento time, and 127 is the longest Portamento time.
1.2.4 Data Entry
This message sets the value of the parameter which was specified by RPN (see
1.2.18) and NRPN (see 1.2.17).
Control# Parameter
6 Data Entry MSB
38 Data Entry LSB
1.2.5 Main Volume
This message controls the volume of each part. (It is used to adjust the volume
balance between parts.)
Control# Parameter
7 Main Volume
When the Multi Part parameter Rcv VOLUME = OFF, that part will not receive
Main Volume. With a value of 0 there will be no sound, and a value of 127 will
produce the maximum volume.
This message is processed on the host device (e.g., MOTIF ES, MU128, etc.)
1.2.6 Panpot
This message controls the panning (stereo location) of each part.
Control# Parameter
10 Pan
When the Multi Part parameter Rcv PAN = OFF, that part will not receive Pan-
pot. 0 is left, 64 is center, and 127 is right.
This message is processed on the host device (e.g., MOTIF ES, MU128, etc.)
Data Range
0...127
(32:Preset,80:AP-XG/A,96:AP-XG/B)
0...127
Data Range
0...127
Data Range
0...127
Data Range
0...127
0...127
Data Range
0...127
Data Range
0...64...127
1.2.7 Expression
This message controls expression for each part. It is used to create volume
changes during a song.
Control# Parameter
1l Expression
If the Multi Part parameter Rcv EXPRESSION = OFF, that part will not receive
Expression.
This message is processed on the host device (e.g., MOTIF ES, MU128, etc.)
1.2.8 Holdl
This message controls sustain pedal on/off.
Control# Parameter
64 Hold1
When this is ON, currently-sounding notes will continue to sound even if note-
off messages are received. If the Multi Part parameter Rcv HOLD1 = OFF, that
part will not receive Holdl.
1.2.9 Portamento
This message controls Portamento pedal on/off.
Control# Parameter
65 Portamento
When ON, Portamento produces a smooth glide connecting two notes of differ-
ent pitch. The time over which the pitch changes is adjusted by Portamento Time
(see 1.2.3). When the Multi Part Parameter MONO/POLY MODE = MONO, the
tone will also change smoothly (legato) if Portamento = ON.
If the Multi Part parameter Rcv PORTAMENTO = OFF, that part will not receive
Portamento.
1.2.10 Sostenuto
This message controls sostenuto pedal on/off.
Control# Parameter
66 Sostenuto
If sostenuto is turned on while a note is sounding, that note will be sustained until
sostenuto is turned OFF.
If the Multi Part parameter Rcv SOSTENUTO = OFF, that part will not receive
Sostenuto.
1.2.11 Soft Pedal
This message controls soft pedal on/off.
Control# Parameter
67 Soft Pedal
When ON, the sound is soft.
If the Multi Part parameter Rcv SOFT PEDAL = OFF, that part will not receive
the Soft Pedal.
1.2.12 Harmonic Content
This message adjusts the resonance of the filter that is specified for the sound.
Control# Parameter
71 Harmonic Content
Since this is a relative change parameter, it specifies an increase or decrease rela-
tive to 64. Higher values will produce a more distinctive sound.
For some sounds, the effective range may be less than the possible range of set-
tings.
1.2.13 Release Time
This message adjusts the EG release time that was specified by the sound data.
Control# Parameter
72 Release Time
Since this is a relative change parameter, it specifies an increase or decrease rela-
tive to 64. Increasing this value will lengthen the release time that follows a note-
off.
PLG150-AP Owner's Manual / Bedienungsanleitung / Mode d'emploi
Data Range
0...127
Data Range
0...63, 64...127
(OFF, ON)
Data Range
0...63, 64...127
(OFF, ON)
Data Range
0...63, 64...127
(OFF, ON)
Data Range
0...63, 64...127
(OFF, ON)
Data Range
0...64...127
(-64...0...+63)
Data Range
0...64... 127
(-64...0...+63)
23