Midi Data Format - Yamaha YC Benutzerhandbuch

DATA LIST

MIDI Data Format

(1) TRANSMIT FLOW
MIDI <-+--[SW1]--+---------NOTE OFF
OUT |
| +---------NOTE ON
| |
| +---------CONTROL CHANGE
| | SUSTAIN
| | ASSIGNABLE CONTROLLER BnH,(01H...76H)
| |
| +--[SW3]--BANK SELECT MSB
| | BANK SELECT LSB
| |
| +--[SW4]--PROGRAM CHANGE
| |
| +---------PITCH BEND CHANGE
|
+-------------------SYSTEM REALTIME MESSAGE
| ACTIVE SENSING
|
+--[SW2]--+---------SYSTEM EXCLUSIVE MESSAGE
| |
| +---------<BULK DUMP>
| | F0H 43H 0nH 7FH 1CH bhH blH 09H ahH amH
| | alH ddH....ddH ccH F7H
| |
| +---------<PARAMETER CHANGE>
| F0H 43H 1nH 7FH 1CH 09H ahH amH alH
| ddH...ddH F7H
|
+-------------------SYSTEM EXCLUSIVE MESSAGE
IDENTITY REPLY
F0H 7EH 7FH 06H 02H 43H 00H 41H ddH ddH
mmH 00H 00H 7FH F7H
dd: Device family number/code
YC61: 5CH 06H
mm: version
mm=(version no.-1.0)*10
e.g.)version 1.0 mm=(1.0-1.0)*10=0
[SW1] MIDI Transmit Channel
Complies with Zone Transmit Channel when the Master Keyboard Mode SW is set to
on.
Complies with MIDI Transmit Channel in any other case.
[SW2] SYSTEM MIDI Device Number
When set to "all," transmitted via "1."
[SW3] SYSTEM Bank Select Switch
[SW4] SYSTEM Program Change Switch
(2) RECEIVE FLOW
MIDI >-+--[SW1]--+---------NOTE OFF
| |
| |---------NOTE ON/OFF
| |
| +---------CONTROL CHANGE
| | MODULATION
| | PEDAL WAH
| | CHANNEL VOLUME
| | EXPRESSION
| | SUSTAIN
| | SOSTENUTO
| | SOFT
| | PORTAMENTO CONTROL
| |
| +--[SW3]--BANK SELECT MSB
| | BANK SELECT LSB
| |
| +---------CHANNEL MODE MESSAGE
| | ALL SOUND OFF
| | RESET ALL CONTROLLERS BnH,79H
| | ALL NOTE OFF
| | OMNI MODE OFF
| | OMNI MODE ON
| |
| +--[SW4]--PROGRAM CHANGE
| |
| +---------PITCH BEND CHANGE
|
+-------------------SYSTEM REALTIME MESSAGE
| ACTIVE SENSING
|
+--[SW2]--+---------SYSTEM EXCLUSIVE MESSAGE
| |
| +---------<BULK DUMP>
| | F0H 43H 0nH 7FH 1CH bhH blH 09H ahH amH
| | alH ddH...ddH ccH F7H
| |
| +---------<PARAMETER CHANGE>
| | F0H 43H 1nH 7FH 1CH 09H ahH amH alH
| | ddH...ddH F7H
| |
| +---------<BULK DUMP REQUEST>
| | F0H 43H 2nH 7FH 1CH 09H ahH amH alH F7H
| |
| +---------<PARAMETER REQUEST>
| F0H 43H 3nH 7FH 1CH 09H ahH amH alH F7H
62 YC61 Owner's Manual
8nH
9nH
BnH,40H
BnH,00H
BnH,20H
CnH
EnH
FEH
version 1.5 mm=(1.5-1.0)*10=5
8nH
9nH
BnH,01H
BnH,04H
BnH,07H
BnH,0BH
BnH,40H
BnH,42H
BnH,43H
BnH,54H
BnH,00H
BnH,20H
BnH,78H
BnH,7BH
BnH,7CH
BnH,7DH
CnH
EnH
FEH
|
+-------------------SYSTEM EXCLUSIVE MESSAGE
IDENTITY REQUEST F0H 7EH 0nH 06H 01H F7H
[SW1] Complies with MIDI Receive Channel.
[SW2] SYSTEM MIDI Device Number
[SW3] SYSTEM Bank Select Switch
[SW4] SYSTEM Program Change Switch
(3) TRANSMIT/RECEIVE DATA
(3-1) CHANNEL VOICE MESSAGES
(3-1-1) NOTE OFF
STATUS 1000nnnn(9nH)
NOTE No. 0kkkkkkk
VELOCITY 0vvvvvvv
(3-1-2) NOTE ON/OFF
STATUS 1000nnnn(8nH)
NOTE No. 0kkkkkkk
VELOCITY NOTE ON 0vvvvvvv(v≠0)
NOTE OFF 0vvvvvvv(v=0)
(3-1-3) CONTROL CHANGE
STATUS 1011nnnn(BnH)
CONTROL NUMBER 0ccccccc
CONTROL VALUE 0vvvvvvv
*TRANSMITTED CONTROL NUMBER
c=0 BANK SELECT MSB
c=32 BANK SELECT LSB
c=64 SUSTAIN
c=1...119 ASSIGNABLE CONTROLLER
*RECEIVED CONTROL NUMBER
c=0 BANK SELECT MSB
c=32 BANK SELECT LSB
c=1 MODULATION
c=4 PEDAL WAH
c=7 CHANNEL VOLUME
c=11 EXPRESSION
c=64 SUSTAIN
c=66 SOSTENUTO
c=67 SOFT
c=84 PORTAMENTO CONTROL
*1 Relation between BANK SELECT and PROGRAM is as follows:
CATEGORY MSB
Live Set Page 1 63
: :
Live Set Page 20 63
*2 The default CONTROL NUMBERs of ASSIGNABLE CONTROLLER are as
follows:
MODULATION
FOOT CONTROLLER 1
FOOT CONTROLLER 2
FOOT SWITCH Live Set Inc
*3 When Sustain is set to something other than "FC3A (HalfOn),"
operating the foot switch transmits only values of 0 (off) or
127 (on).
Bank Select will be actually executed when a Program Change message is received.
Bank Select and Program Change numbers that are not supported by this instrument
will be ignored.
(3-1-4) PROGRAM CHANGE
STATUS 1100nnnn(CnH)
PROGRAM NUMBER 00000ppp
(3-1-5) PITCH BEND CHANGE
STATUS 1110nnnn(EnH)
LSB 0vvvvvvv
MSB 0vvvvvvv
Transmitted with a resolution of 7 bits.
(3-2) CHANNEL MODE MESSAGES
STATUS 1011nnnn(BnH)
CONTROL NUMBER 0ccccccc
CONTROL VALUE 0vvvvvvv
(3-2-1) ALL SOUND OFF (CONTROL NUMBER = 78H, DATA VALUE = 0)
All the sounds currently being played, including channel messages such as note-on
of a certain channel, are muted this message is received.
(3-2-2) RESET ALL CONTROLLERS (CONTROL NUMBER = 79H, DATA VALUE = 0)
Resets the values set for the following controllers.
PITCH BEND CHANGE 0 (center)
MODULATION 0 (minimum)
PEDAL WAH 0 (minimum)
EXPRESSION 127 (maximum)
SUSTAIN 0 (off)
SOSTENUTO 0 (off)
SOFT 0 (off)
PORTAMENTO CONTROL Clear the reserved note number
n=0-15 CHANNEL NUMBER
k=0(C-2)-127(G8)
v=64 Transmit
n=0-15 CHANNEL NUMBER
k=0(C-2)-127(G8)
n=0-15 CHANNEL NUMBER
;v=0-127 *1
;v=0-127 *1
;v=0-127 *3
;v=0-127 *2
;v=0-127 *1
;v=0-127 *1
;v=0-127
;v=0-127
;v=0-127
;v=0-127
;v=0-127
;v=0-63:OFF, 64-127:ON
;v=0-127
;v=0-127
LSB PROGRAM No.
0 0..7
:
19 0..7
1
11
4
n=0-15 CHANNEL NUMBER
p=0-7
n=0-15 CHANNEL NUMBER
PITCH BEND CHANGE LSB
PITCH BEND CHANGE MSB
n=0-15 CHANNEL NUMBER
c=CONTROL NUMBER
v=DATA VALUE