Siemens SINUMERIK 840D sl Bedienhandbuch Seite 14

Inhaltsverzeichnis
10.4.2 Abspanen (CYCLE951)........................................................................................................478
10.4.3 Einstich (CYCLE930)...........................................................................................................482
10.4.4 Freistich Form E und F (CYCLE940)...................................................................................487
10.4.5 Freistich Gewinde (CYCLE940)...........................................................................................493
10.4.6 Gewindedrehen (CYCLE99) - nur G-Code..........................................................................500
10.4.7 Gewindekette (CYCLE98)....................................................................................................528
10.4.8 Abstich (CYCLE92)..............................................................................................................537
10.5 Konturdrehen - Fräs-/Drehmaschine....................................................................................541
10.5.1 Allgemeines..........................................................................................................................541
10.5.2 Darstellung der Kontur.........................................................................................................542
10.5.3 Neue Kontur anlegen...........................................................................................................544
10.5.4 Konturelemente erstellen.....................................................................................................545
10.5.5 Kontur ändern......................................................................................................................551
10.5.6 Konturaufruf (CYCLE62)......................................................................................................552
10.5.7 Abspanen (CYCLE952)........................................................................................................553
10.5.8 Abspanen Rest (CYCLE952)...............................................................................................567
10.5.9 Stechen (CYCLE952)...........................................................................................................571
10.5.10 Stechen Rest (CYCLE952)..................................................................................................581
10.5.11 Stechdrehen (CYCLE952)...................................................................................................585
10.5.12 Stechdrehen Rest (CYCLE952)...........................................................................................596
10.6 Weitere Zyklen und Funktionen...........................................................................................600
10.6.1 Schwenken Ebene/Werkzeug (CYCLE800).........................................................................600
10.6.2 Schwenken Werkzeug (CYCLE800)....................................................................................610
10.6.2.1 Schwenken Werkzeug/Anstellen von Fräswerkzeugen - nur bei G-Code-Programm
(CYCLE800).........................................................................................................................610
10.6.3 Ausrichten von Drehwerkzeugen (CYCLE800) - Fräs-/Drehmaschine................................611
10.6.4 High Speed Settings (CYCLE832).......................................................................................616
10.6.5 Unterprogramme..................................................................................................................620
10.7 Weitere Zyklen und Funktionen ShopMill.............................................................................622
10.7.1 Transformationen.................................................................................................................622
10.7.2 Verschiebung.......................................................................................................................623
10.7.3 Rotation................................................................................................................................624
10.7.4 Skalierung............................................................................................................................625
10.7.5 Spiegelung...........................................................................................................................625
10.7.6 Zylindermanteltransformation...............................................................................................626
10.7.7 Gerade oder kreisförmige Bearbeitungen............................................................................629
10.7.8 Gerade programmieren........................................................................................................631
10.7.9 Kreis mit bekanntem Mittelpunkt programmieren.................................................................632
10.7.10 Kreis mit bekanntem Radius programmieren.......................................................................633
10.7.11 Helix.....................................................................................................................................634
10.7.12 Polarkoordinaten..................................................................................................................635
10.7.13 Gerade polar........................................................................................................................636
10.7.14 Kreis polar............................................................................................................................637
10.7.15 Hindernis..............................................................................................................................638
11 Mehrkanalansicht.....................................................................................................................................641
11.1 Mehrkanalansicht.................................................................................................................641
11.2 Mehrkanalansicht im Bedienbereich "Maschine".................................................................641
11.3 Mehrkanalansicht bei großen Bedientafeln..........................................................................643
14
Bedienhandbuch, 05/2017, A5E40868956
Fräsen