Siemens SINUMERIK 840D sl Bedienhandbuch Seite 13

9.18.2 Programmierung..................................................................................................................318
9.18.3 Ergebnisse/Simulationstest..................................................................................................329
9.18.4 G-Code-Bearbeitungsprogramm..........................................................................................331
10 Technologische Funktionen programmieren (Zyklen)..............................................................................335
10.1 Bohren..................................................................................................................................335
10.1.1 Allgemeines..........................................................................................................................335
10.1.2 Zentrieren (CYCLE81).........................................................................................................336
10.1.3 Bohren (CYCLE82)..............................................................................................................338
10.1.4 Reiben (CYCLE85)..............................................................................................................341
10.1.5 Tieflochbohren 1 (CYCLE83)...............................................................................................343
10.1.6 Tieflochbohren 2 (CYCLE830).............................................................................................347
10.1.7 Ausdrehen (CYCLE86)........................................................................................................358
10.1.8 Gewindebohren (CYCLE84, 840)........................................................................................360
10.1.9 Bohrgewindefräsen (CYCLE78)...........................................................................................367
10.1.10 Positionen und Positionsmuster...........................................................................................371
10.1.11 Beliebige Positionen (CYCLE802).......................................................................................372
10.1.12 Positionsmuster Reihe (HOLES1)........................................................................................376
10.1.13 Positionsmuster Gitter oder Rahmen (CYCLE801)..............................................................377
10.1.14 Positionsmuster Kreis oder Teilkreis (HOLES2)..................................................................379
10.1.15 Positionen ein- und ausblenden...........................................................................................382
10.1.16 Positionen wiederholen........................................................................................................383
10.2 Fräsen..................................................................................................................................384
10.2.1 Planfräsen (CYCLE61).........................................................................................................384
10.2.2 Rechtecktasche (POCKET3)...............................................................................................387
10.2.3 Kreistasche (POCKET4)......................................................................................................393
10.2.4 Rechteckzapfen (CYCLE76)................................................................................................401
10.2.5 Kreiszapfen (CYCLE77).......................................................................................................405
10.2.6 Mehrkant (CYCLE79)...........................................................................................................409
10.2.7 Längsnut (SLOT1)................................................................................................................413
10.2.8 Kreisnut (SLOT2).................................................................................................................420
10.2.9 Offene Nut (CYCLE899)......................................................................................................426
10.2.10 Langloch (LONGHOLE) - nur für G-Code Programme........................................................434
10.2.11 Gewindefräsen (CYCLE70)..................................................................................................436
10.2.12 Gravur (CYCLE60)...............................................................................................................440
10.3 Konturfräsen.........................................................................................................................445
10.3.1 Allgemeines..........................................................................................................................445
10.3.2 Darstellung der Kontur.........................................................................................................446
10.3.3 Neue Kontur anlegen...........................................................................................................447
10.3.4 Konturelemente erstellen.....................................................................................................449
10.3.5 Kontur ändern......................................................................................................................454
10.3.6 Konturaufruf (CYCLE62) - nur bei G-Code-Programm........................................................455
10.3.7 Bahnfräsen (CYCLE72).......................................................................................................456
10.3.8 Konturtasche/Konturzapfen (CYCLE63/64).........................................................................460
10.3.9 Konturtasche vorbohren (CYCLE64)...................................................................................462
10.3.10 Konturtasche fräsen (CYCLE63)..........................................................................................465
10.3.11 Konturtasche Restmaterial (CYCLE63)...............................................................................470
10.3.12 Konturzapfen fräsen (CYCLE63).........................................................................................472
10.3.13 Konturzapfen Restmaterial (CYCLE63)...............................................................................476
10.4 Drehen - Fräs-/Drehmaschine..............................................................................................478
10.4.1 Allgemeines..........................................................................................................................478
Fräsen
Bedienhandbuch, 05/2017, A5E40868956
Inhaltsverzeichnis
13