Description Of Machine And Its Components; User Manual; Assembling The Machine; Machine Assembly Procedure - Vari Hurricane F-550 Bedienungsanleitung

Engine
Model
Maximum engine RPMs (set)
Maximum engine incline / short-term
Fuel tank capacity
Fuel
Engine oil capacity
Oil rating
Spark plug
Table 5: Basic engine information

2.3.2 Description of machine and its components

The F-550 brush cutter frame (on Pic. 3 ) is made of a welded steel frame
components are attached to. The handlebars are mounted to the frame with screw connections
six positions. All control elements (
The handle 12 is used to firmly grasp and direct the machine during operation. A wheel drive clutch lever
side of the handlebars, which controls the motion of the machine forward. On the right side is a tool drive clutch lever
a safety lock to prevent accidental operation
handles in an emergency, both of the control levers return to the default position and the engine is disengaged from transmitting force. The
blade drive is equipped with an automatic braking device, which stops the blade
by the throttle lever 4 . Motion is secured by wheels
shifting of force to the wheel via a belt-driven clutch (the machine moves forward without jerking) . The wheel and blade drive transmission
part are covered by plastic housing
plastic cover 9 connected by screws to the frame. Pressed on the shaft at the front of the frame is a blade holder with blade
blade is fixed and sharp at the ends. The main deck comprises a cover
for the front, spans further than the blade to prevent injury to the operator from flying parts of the mowed area. The deck is riveted from
several parts and screwed to the frame. A plastic shroud is fastened between the wheels. During operation, the machine is guided by a
swivel, height-adjustable spur

2.4 User manual

2.4.1 Assembling the machine


Assembly and operating instructions are available from your retailer as a component of pre-sales service!
Handling points when removing the machine from the box (see Pic. 1 ): ahead of the engine behind the square tube
plate, at the back of the machine frame tube

2.4.1.1 Machine assembly procedure

Use the following procedure when assembling: ( We recommend that another person be present to assist you during assembly )
According to Pic. 1 - remove the bag with manuals
1)
handlebars. Hold the machine at the front
2) According to Pic. 3 - remove the screw connections
around and place them on the tube at the rear frame (select one of the three holes in the handlebars to set their height and one
of the two holes in the frame tube). Tighten the screw joints securely by hand. Control lever cables must not be crossed – this
reduces their life!
3) Remove the tie straps from the bag with manuals and attach the control lever cables at the top of the handlebar tube bend.
Only 2 tie straps are required for fastening.
According to Pic. 2 - remove the paper insert (
4)
onto the handlebars so the rear frame rests on a mat, and secure the machine from tilting back forward. Remove 2 M8 screw
connections ( 1 and
the spur arm so that the holes in the spur arm are concentric with the holes in the machine frame. You will feel light cushioning.
Insert the screws

2.4.2 Commissioning


The machine may be supplied without engine fluids (depending on various national regulations)!

First, carefully read the engine operating manual
More information about the engine including replacement part numbers can be found at www.honda-engines-eu.com
53
54 More information about the engine including replacement part numbers can be found at www.briggsandstratton.com
More information about the engine including replacement part numbers can be found at www.honda-engines-eu.com
55
56 Short-term = within one minute
57 Measured according to the Society of Automotive Engineer (SAE) standard J1349
Measured according to the Society of Automotive Engineer (SAE) standard J1349
58
59 Vzhledem ke stále se zvyšujícímu podíliu BIOsložkek v palivu používejte stabilizátor paliva.
Automatic brake is an active protective element that increases the safety of the machine.
60
61 Original engine manual and Czech translation is included in the machine packaging.
22
Unit F-550 , F-550G
- HONDA GCV190A N2G7
min -1
56 ∠ 20° / 30°
l (liter) 0,91 57
gasoline
l (liter) 0,55
SAE / API
- NGK BPR6ES
1 , 2 and 4 ) for safe control of the machine are ergonomically distributed along the handlebars.
16 , which turns the work tool (blade) drive on or off. If the operator releases the
15
9 and 10 . The brake, blade drive clutch, and belt gears in front are also covered from above by a
5 , which is attached to the front of the machine frame.
4 .
5 and back
3 ) holding the cover. Hook the tab
3 through the holes and attach the nuts
F-550B
53 B&S 850Series TM
3200 ± 100
15° / 30°
1,13
oct.No. 91-95
0,59
SAE 30 or 10W30 / SJ or SH
CHAMPION QC12YC
11 from formed sheet metal, which all essential machine
60 in the event of an emergency. Motor speed is controlled
with arrows pattern, which are driven by a worm-gear unit. It provides smooth
made from hot-dip galvanized (HDG) sheet metal, which except
8
2 , spur arm 3 and unfold the paper insert
4 handling points, and remove it from the box.
3 from both sides of the frame tube, remove the handlebars, turn them
in Pic. 1 ) from the front of the main deck cover, tilt the machine backwards
6
2 on the spur arm
1 . Tighten the screw connection.
61 ! This will help prevent any engine damage.
F-550 INOX
122R02-0122-B1 54 HONDA GSV190A N2G7SD
20° / 30°
0,91 58
59
0,55
NGK BPR6ES
3 and their height may be adjusted into
2
5 into the machine frame groove
F-550
55
is located on the left
1 equipped with
7 . The
5 on the engine
7 underneath the
4 . Lower