Installation Modes; Size And Speci Cations Of The Room In Hich To Install The Air Conditioner; Choosing The Position Of The Unit; Unit Assembly - Olimpia splendid UNICO AIR Handbuch Für Installation, Gebrauch Und Wartung

2
2.1

INSTALLATION MODES

To obtain the best results and optimum performance follo the instructions for correct installation provided in this manual. Failure
to follo the instructions and appl the rules indicated ma cause malfunction of the appliance and relieves the manufacturer
OLIMPIA SPLENDID of an form of guarantee and liabilit for damages to persons animals or propert .
The electrical system must comply with the regulations and rating data in the technical sheet, with good grounding.
Before installing the air conditioner it is essential to make an accurate calculation of the heat load in summer (and cold load in
inter for models ith heating pump) at the site of installation.
The more accurate this calculation is made the better the air conditioner ill be able to do its ob.
When executing the calculations refer directl to the prevailing standards.
For particularl important applications
The user should tr to limit high heat loads as much as possible as follo s: glass doors and indo s exposed to man hours of
sunlight should be tted on the inside ith curtains or even better on the outside ith coverings such as Venetian blinds veran-
dahs refractive lm etc.). The air-conditioned room must remain closed as long as possible.
Halogen spotlights or other electrical equipment
irons hot plates for cooking etc.).
2.2

CHOOSING THE POSITION OF THE UNIT

The position for installing the unit to obtain best performance and avoid breakdo ns or hazards must have the follo ing requisites
( g. 3):
- The height of the unit's lo er edge from the oor should be at least 100 mm if xed to the all in the lo est position.
- If xed to the all in the highest position it should be at least 80 mm from the ceiling.
- The all on hich the inside unit is installed must be sturd and able to ithstand its eight.
- It must be possible to leave room around the unit for an maintenance operations that ma be necessar .
- Nothing should be in the a of the air that needs to circulate both on the top air-intake (curtains plants furniture) and at the
front here the air exits. This could cause air s irls that ould inhibit the orking ef cienc of the unit.
The air conditioner must be installed on a wall that communicates with the outside.
CAUTION: after determining the best place for installation as described above, check for the absence of other structures
or systems (beams, piers, pipes, wires, etc.) at the points where the holes are to be drilled, which would prevent drilling
the holes required to install the unit.
Check again to make sure there are no obstacles to air circulation through the holes to be drilled due to plants and their
leaves, slats or panelling, blinds, gratings or grids too dense, etc.).
WARNINGS ( g. 4):
- it should not be placed under curtains;
- do not spra
- it should not be installed in a position here the air o can directl strike people in the hereabouts.
- never force the opening of the air o
- do not place bottles cans clothing o ers or an other ob ect that ma damage the internal organs on the air aspiration
grill or an thing that ma even partiall obstruct the grill itself;
- it should not be directl over another appliance (television set radio refrigerator etc.) or over a source of heat.
2.3

UNIT ASSEMBLY

2.3.1

Warning

The maximum length allo ed for pipes is 1 m. The pipes must be smooth on the inside. Pipes cannot be curved or bent.
It is necessar to use the grilles provided or grilles hich keep the same features.
2.3.2 Drilling the wall
Install the unit b drilling t o holes diameter either 162 mm in the all as indicated in the drilling template.The UNICO unit ma
be installed in lieu of a UNICO unit
condensate drainage. In this case in order not to penalize performance remove the insulating material from the air outlet pipe.
Drill the all using the proper tools to facilitate our ob and prevent excess damage or disturbance to our client. The best tools
for drilling large holes in
depending on the diameter of the hole to be drilled.
INSTALLATION
e recommend contacting expert heating engineers.
ith high po er consumption should not be used in the room (toasters steam
ater or other liquids of an kind directl on the unit;
ap;
ithout changing the position of the existing holes
alls are special drills called core borers
ith the exception of the small hole for
ith ver high t isting torque and ad ustable rotating speed
2
29
UNICO AIR