Jacuzzi J-470 Montageanweisung Und Bedienung Und Wartung Seite 79

5
2
17
6
8
16
12
Adjusting I-VOL Level
This function defines the maximum volume when the system
is turned on (under all circumstances the volume when the
system is turned on will always be equal to 20 even if it was,
for example, 20 and I-VOL 30 when it was turned off).
Keep the EQ (5) pushbutton pressed down for approximately 2
seconds and press repeatedly until "I-VOL" appears on the
display. Use the volume (3) pushbutton to select the desired
value (from 0 to 45) that will be automatically defined;
Note: Unit returns to volume mode if volume control is not ope-
rated for 3 seconds.
Adjusting Area
In Radio mode, press and hold the EQ button (5) for about 2
seconds, then repeatedly press until display reads "AREA USA"
or "AREA EUR". Press VOL Up/Down button (3) to choose desi-
red setting, then press and hold the BND button (8) for 2
seconds to confirm selection.
Note: Unit returns to volume mode if volume control is not ope-
rated for 3 seconds.
Open/Close Front Panel
Press firmly on the release button (15), then open front panel
(16) by gently lifting upward on bottom edge. To close front
panel, gently flip panel down, then press firmly on panel direc-
tly above release button (15) until you hear an audible "click".
Keep front panel closed at all the times to prevent water intru-
sion, except when changing discs.
CAUTION: Never insert wet discs into unit or CD player will
be damage!
7
3
4
9
1
10
11
13
14
15
J-1000™ AUDIO SYSTEM RADIO OPERATION
Press MODE button (4) to select Radio mode. Station frequency
is indicated on display.
To Select Band: Press BAND button (8) repeatedly to scroll
through radio mode as follows: FM1 --> FM2 --> FM3 --> AM1
--> AM2 -->FM1. Each radio band stores up to 6 independent
stations, for a total of 18 FM and 12 AM presets.
To Program Station Presets in Radio mode: Press and hold SH but-
ton (9) until display reads "SHIFT". Immediately afterwards, press
and hold the Tune up/down button (2) for 2 seconds, then repea-
tedly press to select preset 1 to 6. At desired preset, press the ENT
button (9) to store current frequency into selected preset.
Note: When power to spa is shut off for any reason, all station
presets are reset.
Automatically Setting Station Presets
Press and hold the AS/ PS button (6) for approximately 2
seconds until you hear a beep that confirms the memory func-
tion is engaged. The unit will search for six strong stations and
automatically store them on the current band. All 18 FM and 12
AM presets can be set sequentially by selecting the next band
and continuing the operation during auto programming.
Seek/Manual Tune
Press TUN up/down button (2) once to activate manual tuning
mode, then press TUN up or down repeatedly to manually
increase or decrease displayed frequency. Press and hold either
TUN up or down button (2) for at least 2 seconds to activate auto
tuning mode. The unit will automatically search and stop at the
next higher or lower station with sufficient signal strength.
Preset Scan Function
Press AS/PS button (6) once to enter scan mode. Each preset
station in the current band will play for 5 seconds while the pre-
set number is flashes on the display (17). At the desired station,
press AS/PS button (6) a second time.
Accessing Preset Stations
Press and hold ENT/SH button (9) until display reads "SHIFT".
Repeatedly press TUN up or down button (2) to choose preset
1-6, then press ENT/SH button (9) to confirm selection.
J-1000™ AUDIO SYSTEM CD PLAYER OPERATION
Insert, Play, and Eject a CD
Open front panel (16) by pressing firmly on release button (15)
and lifting panel upward from bottom edge. Gently insert CD into
slot (14) with label facing up. The CD will be drawn inside by the
motorized mechanism.
DO NOT FORCE! Close front panel by folding down, then press
firmly on panel directly above release latch (15) until you hear
an audible "click". Keep front panel closed at all the times to pre-
vent water intrusion, except when changing discs. CD playback
will automatically begin after CD is loaded. A "S-CDP" icon on
the display indicates that a disc is inside the mechanism.
79