Settings 2 Menus - Jacuzzi J-470 Montageanweisung Und Bedienung Und Wartung

Settings 2 menus

Programming Instructions for Settings 2 Menus
The "Settings 2" screen allows you to program the Primary Fil-
ter mode, Secondary Filter mode and access the "Settings 3"
Submenus.
From the "Settings 1" Menu, press button B.
SETTINGS 1
A
Heating
UV Light
1
Filter
B
2
set filter or UV timer
The "Settings 2" Menu will appear.
SETTINGS 2
A
Primary
Secondary
2
B
3
Note: You can return to the factory default filtration modes by
pressing the Splash button on the Quad Keypad while in the
Settings 2 Main Menu at any time.
Primary Filter Cycle: Press button A to access the Pri-
mary filtration submenus.
Secondary Filter Cycle: Press button C to access the
Secondary filtration submenus.
3
Settings 3 Menu: Press button B to access the "Set-
tings 3" Submenus.
Previous: Press button D to go to the previous menu.
I
Programming the Primary Filter Cycle
To program the Primary Filter cycle press button A. This cycle
is mainly used to alter the pre-programmed 12-hour running
period of the circulation pump. The 12-hour cycle is from
12:00 AM to 12:00 PM. (If you would like to leave the circu-
lation pump as is, then skip this section). Upon entering the
Primary submenu the "Start Time" will be selected.
PRIMARY
Start Time
Start Time
1PM
Select
Duration
3
Press to Save
C
ENERGY EFFICIENT
0 Days
OFF
D
Press to
C
OFF
OFF
D
Press to
reset to default
I
Press the Left or Right button on the Quad Keypad to choo-
se the hour you want the circulation pump to start running.
Note: If you are using a standard 12-hour period, you will
see the hour displayed as "1PM." For the 24-hour period it will
read "1300."
I
Now you will need to adjust the "Duration" of the cycle.
Press the Down button to select "Duration." Press the Left or
Right button on the Quad Keypad to make adjustments in in-
crements of 1 hour. Press the Splash button on the Quad Key-
pad to save hour and duration selections and return to the Set-
tings 2 Main Menu.
PRIMARY
Start Time
Duration Duration 12hr
3
Press to Save
Summer Logic:
In warm weather, the water temperature in the spa may exceed the
set temperature. This condition may occur due to heat transferen-
ce from the filter/circulation pump and jets pumps. If the water
temperature is higher than 35°C and rises two degrees above the
set temperature, a "Summer Logic" condition occurs that deactiva-
tes the filter/circulation pump and CLEARRAY™. This safety featu-
re cannot be altered! The filter/circulation pump and CLEARRAY™
will remain off until the water temperature cools to the set tempe-
rature (except between 9am-11am when the filter/circulation
pump runs for it's mandatory 2 hour cycle.) To help prevent a
"Summer Logic" condition, it may be necessary to reduce fil-
ter/circulation pump cycles run times in warm weather.
Programming the Secondary Filter Cycle
To program the Secondary Filter cycle, press button C. This
cycle will activate the main jet pump to run for additional fil-
tration when programmed. If you choose not to use this fea-
ture, please skip this section.
SETTINGS 2
Primary
Secondary
OFF
2
3
Press to
reset to default
When you enter the Secondary Filter Cycle submenu, the
"Day Settings" will be selected. From this menu, you can set
the day, time, and duration. Press the Splash button on the
Quad Keypad to confirm selection.
You can choose the day (s) you would like to run a secondary
filter cycle. Press the Up or Down button on the Quad Keypad
to scroll through and change the days you would like the fil-
tration to run. Press the Left or Right button to turn "ON" (
) or "OFF" the filtration for that day.
69
Select
SECONDARY
Day Settings Day Settings
Start Time
Duration
3
Press to Enter
Select