Assembly; Function - Scheppach MTP900 Original Bedienungsanleitung

Measured acoustic power level L
K uncertainty: 3 dB(A)
Measured acoustic power level L
K uncertainty: 2 dB(A)
Guaranteed acoustic power level L
vibration value a
hw
K uncertainty: 1.5 m/s
ATTENTION: The value of vibration emitted during
product usage may differ from the declared value
depending on the circumstances.
Safety measures to protect the operator are based
on an estimate of exposure under normal conditions
of use (taking into account all operating cycles such
as the time when the tool is shut off, when operating
empty or in use).

7. Assembly

1. Mount the external parts of the tine (12.1) on the
internal parts (12.2), and attach side discs (11) to
each end, fi xing them together with (C) M8x45. (Fig.
3)
2. Place tilling tines (12) on the tine shaft (D) on both
sides of the transmission box. Line up the holes in
the tine frame sleeves and tine shaft. Insert M10x45
screws (E) through the holes in tine frames and tine
shaft from one side, then lock nuts from the other
side. Tighten down. 3 pairs tilling tines (12) can be
adjusted according to the operator's tilling width to
372/612/852 mm respectively. (Fig. 4)
3. Loosen the screw, washer and nut (F) from shift
lever (7), install shift lever (7) in the proper position
and then tighten down. (Fig. 5)
M F D E / A T / C H D E / A T / C H
4. Mount the wheels (10) on both sides of the wheel
bracket (9) with M8x20 screws and washers (G).
(Fig. 6)
5. Wheel bracket (9) with notched plate (H) is welded
on the connecting rack. Fix connecting rack to the
chassis with M8x60 screws (J), bushes and nuts.
(Fig. 7)
6. Attach the tine shield extension (13) to the tine
shield with M5x12 screws (K) and nuts. (Fig. 8)
7. Put the handlebar (5) in the groove (L) between
the two fi xing plates and secure it with the handlebar
adjustment star knob (6). (Fig. 9)
8. Fix the tool kit (3) on the crosspiece between the
handles (M) with M5x25 screws (N). (Fig. 10)
9. Use cable clips (O) to secure the clutch control
cable and throttle control cable (P) in place on the
handlebars. Make sure the control cables are routed
properly. (Fig. 11)
: 84 dB(A)
pA
: 93 dB(A)
wA
: 95 dB(A)
wA
: 6.103 m/s
2
2
10. Insert the depth regular rod (8) in the groove
(Q) at the rear of the connecting rack (9), with the
pointed end downward and the notched side inward.
The depth regulator rod (8) can be put into differ-
ent grooves and secured with (Ø 10mm) clevis pin
(R) and (Ø 2.5mm) cotter pin (S) to adjust the tilling
depth. When the proper position is obtained, screw
the adjusting bar (T) M12 to make the depth regula-
tor rod (8) fastened. (Fig. 12)
Adding motor oil
m ATTENTION! OIL HAS BEEN DRAINED FOR
SHIPPING.
Failure to fi ll engine sump with oil before starting
engine will result in permanent damage and void
engine warranty (see Engine operator´s manual ).

8. Function

Engine Stop Switch (1)
It cuts out power to the machine at the end of work-
ing or when a problem occurs.
Tine clutch control (4)
Push down to engage tines into forward; releasing
returns machine to neutral.
Throttle lever (2)
lt controls engine speed. Moving the throttle lever in
the directions shown makes the engine run faster or
slower. (Fig. 1.2)
Speed shift lever (7)
lt controls different speeds forward and reverse as
shown on the selector. (Fig. 1.1)
Side discs (11)
They help to keep the machine going straight, pro-
vide a clear edge to the tiled zone, stop soil being
fl ung out to cover vegetable crops and also prevent
damage to the roots of plants.
Transport Wheel (9)
Set the wheel down when transporting the tiller. Tilt
the machine back until the tines clear the ground.
Push or pull the unit to the next location.
Handlebar (5)
Driving position is comfortable with the controls po-
sitioned ergonomically. The handlebars are adjust-
able in height and sideways. Special silent-blocks
absorb the vibrations produced by the machine
when in operation.
Handlebar adjustment star knob (6)
To regulate the height and lateral adjustment of the
handlebar, loosen star knob, adjust handlebar to the
desired position, and then fasten the star knob.
Crosspiece between the handles (3)
Serve a dual purpose. lt bears the tool kit at hand
and keeps the operator a safe distance from the
tines.
23 І 40 23 І 40