Technical Data; Manufacturer's Terms Of Warranty - Truma Trumatic S 3002 K Gebrauchsanweisung

consumption of all devices
installed by the system
manufacturer.
For vehicles we recommend
the Truma caravan regulator
and the Duomatic Plus gas
pressure regulator kit for the
two-bottle system. Truma
regulators have been special-
ly developed for the harsh
stress conditions in caravans
and vehicles. As well as a
safety valve that provides
protection against overpres-
sure, they also have a pres-
sure gauge that can be used
to check the tightness of the
gas system. The pressure
control equipment should be
operated with a de-icing sys-
tem (Eis-Ex) at temperatures
around 0°C and below.
Regulator connecting hoses
that meet national regulations
must always be used in the
respective country for which
the equipment is destined.
These hoses must be
checked regularly for brittle-
ness. Winter-proof special
hoses must always be used if
the equipment is operated
during the winter.
Pressure control de-
vices and hoses must
be replaced with new ones
no more than 10 years after
their date of manufacture.
This is the responsibility of
the operator.
8

Technical data

determined in accordance
with EN 624 or Truma test
conditions
Type of gas:
Liquid gas (propane/butane)
Operating pressure:
30 mbar (28 mbar for butane/
37 mbar for propane) or
50 mbar (see data plate)
Rated thermal output:
3400 W
Gas consumption:
30 – 280 g/h
Operating voltage:
12 V
Power consumption
(12 V):
0,3 – 1,0 A
(incl. Trumavent fan TEB)
Declaration of conformity:
The Trumatic S 3002 K has
been approved by the DVGW
and complies with the EC
guidelines (90/396/EWG) for
gas appliances as well as
with the associated EC guide-
lines. The product ID No. for
EU countries is:
CE-0085AP0325.
ABG test mark:
S 255
EEC Type Approval:
e1 022603
The right to effect technical
modifications is reserved!
Manufacturer's
terms of warranty
1. Case of warranty
The manufacturer grants a
warranty for malfunctions in
the appliance which are
based on material or produc-
tion faults. In addition to this,
the statutory warranty claims
against the seller remain
valid.
A claim under warranty shall
not pertain:
– for parts subject to wear
and in cases of natural
wear and tear,
– as a result of not original
Truma parts being used in
the appliance and as a re-
sult of unsuitable gas pres-
sure regulators being used,
– as a consequence of failure
to respect Truma instruc-
tions for installation and
use,
– as a consequence of
improper handling,
– as a consequence of im-
proper transport packing,
not arranged by Truma.
2. Scope of warranty
The warranty is valid for mal-
functions as stated under
item 1, which occur within
24 months after conclusion
of the purchase agreement
between the seller and the
final consumer. The manufac-
turers will make good such
defects by subsequent fulfil-
ment, i.e. at their discretion
either by repair or replace-
ment. In the event of manu-
facturers providing service
under warranty, the term of
the warranty shall not re-
commence anew with regard
to the repaired or replaced
parts; rather, the old warranty
period shall continue to run.
More extensive claims, in
particular claims for compen-
satory damages by pur-
chasers or third parties, shall
be excluded. This does not
affect the rules of the product
liability law.
The manufacturer shall bear
the cost of employing the
Truma customer service for
the removal of a malfunction
under warranty – in particular
transportation costs, travel-
ling expenses, job and mater-
ial costs, as long as the
service is carried out in Ger-
many. The warranty does not
cover customer service work
in other countries.
Additional costs based on
complicated removal and in-
stallation conditions of the
appliance (e.g. removal of
furniture or parts of the vehi-
cle body) do not come under
warranty.
3. Raising the case of
warranty
The manufacturer's address
is: Truma Gerätetechnik
GmbH & Co. KG, Wernher-
von-Braun Strasse 12,
D-85640 Putzbrunn. In Ger-
many, always notify the
Truma service centre if prob-
lems are encountered; in
other countries the relevant
service partners should be
contacted (see list of ad-
dresses). Any complaints are
to be described in detail. In
addition, the properly com-
pleted guarantee certificate is
to be presented, or the facto-
ry number of the unit and the
date of purchase given.
In order for the manufactur-
ers to be able to determine
whether an incident subject
to guarantee has occurred,
the end user must, at his own
risk, bring the device to the
manufacturers or send it to
them. If there is damage to
heaters (heat exchangers),
the gas pressure regulator
must also be sent back to the
factory.
In instances of the device be-
ing sent to the works, dis-
patch is to be effected by
freight transport. In cases un-
der guarantee, the works
shall bear the transport costs
or the costs of delivery and
return. If the damage is
deemed not to be a warranty
case, the manufacturer shall
notify the customer and shall
specify repair costs which
shall not be borne by the
manufacturer; in this case,
the customer shall also bear
the shipping costs.