Maintenance; Warnings - Elite turbomuin Bedienungsanleitung

the procedure below:
1) Unscrew the nut on the cogset shaft using a 17
mm wrench (Fig. 26).
2) Remove the spacer and the freehub body from
the Turbo Muin shaft (Fig. 27).
3) Fully insert the Campagnolo ® cassette compa-
tible freehub body and replace the spacer (Fig. 28
and Fig. 29).
4) Tighten the cog set shaft nut using a 17 mm
wrench to a torque of 5 Nm (44in-lbs). Use a me-
dium-strength oil tolerant threadlocker to lock the
nut on the shaft.
• You can now mount your Campagnolo
speed cassette onto the freehub body without using
the spacers (L) (Fig. 30).
CAUTION!
Strictly follow the instructions provided by the cas-
sette manufacturer with regard to specific installa-
tion techniques, the need for additional spacers and
torque specifications.
NOTE: Please contact your dealer if you have que-
stions about installation or if you cannot install the
cassette. The warranty does not cover any DAMAGE
to the bicycle and/or Turbo Muin in the event of in-
correct installation.

MAINTENANCE

Turbo Muin does not require any specific scheduled
maintenance, however the following precautions
are recommended:
• wipe the trainer clean with a cloth after each trai-
ning session to prevent the accumulation of dust
and sweat;
• do not clean or degrease the bicycle chain while
the bike is mounted on Turbo Muin as solvents can
cause irreparable damage to the bearings or other
internal mechanical parts;
• Check that the quick release is properly secured
and fully working before every training session;
• the tension of the internal drive belt of every unit
is adjusted and checked by Elite's technical staff.
However, prolonged or intense use can result in
a decline in the tension causing a reduction in the
transmission of the rider's force to the resistance
system. In this case it might be necessary to increa-
se the tension of the drive belt, as explained below:
1) loosen the adjustment locking screw by one full
turn, so that you can then turn the adjusting nut
(Fig. 31).
2) Turn the adjusting nut half a turn to tighten the belt
correctly (Fig. 32).
NOTE: if the belt is still uneven after performing this
operation, repeat step 2) and retest.
3) Tighten the adjustment locking screw (under point
1) by one full turn to set the adjustment (Fig. 33).
• Turbo Muin becomes hot during use. Wait for it
to cool before touching the resistance unit covers.
• Use the Turbo Muin trainer as described in the
9/10/11 manual.
®
• Turbo Muin is not equipped with an emergency
brake.
• Turbo Muin has been designed and manufactu-
red to ensure maximum safety of the user and/or
third parties, but people, children and pets should
be kept away from the trainer during use as contact
with the moving parts of the trainer and the bicycle
may result in damage or injury.
• Never put your fingers or foreign objects of any
kind through the slots on Turbo Muin, as there will
be high risk of damage to the trainer and/or serious
physical injury.
• Before you start training, place the trainer in a
suitable location, away from any potentially dan-
gerous objects (furniture, tables, chairs...) so as to
avoid any risk of accidental or inadvertent contact.
• The Turbo Muin is to be used by only single rider
at a time.
• Always check the safety and stability of the bicycle
on Turbo Muin before training.
• No part of the product has any use beyond its
original application. The warranty will be void if the
unit has been opened or tampered with.
• Since the feet are made of soft non-slip material,
they may leave traces of rubber on the floor during
use.
• If the trainer needs to be shipped for technical
support and/or any other reason, it must be ship-
ped in its original box. Damage due to a failure to
use the original packaging is not covered by the
warranties.
Note: before shipping your trainer or any of its parts
for technical support, you must first consult Elite
or its distributor or your dealer. Any items received
without prior agreement will be rejected

WARNINGS

EN
17