Grundig PA 5 - Turnit Serviceanleitung Seite 30

Allgemeiner Teil / General Section
Selecting tuner
– The first time you select tuner, it automatically switches to FM
STEREO ) and the display indicates 87,50 MHz.
– Your unit is provided with the function 'LAST STATION MEMORY',
which means that the station that was playing when the set was
switched off will be selected again when the tuner is switched back
on.
Selecting the FM STEREO/MONO
• To select the waveband, press MODE and within 2 seconds the +
/ – keys.
You can select the wavebands: FM - STEREO and FM - MONO.
– The display shows the selected band.
– If you have selected FM - STEREO, your unit is in stereo reception
mode, which means that as soon as a stereo signal of sufficient
strength is detected, ' ' appears in the display. If stereo reception
is disturbed, ' ' disappears. In this way, disturbing background
noise is suppressed.
• If noise-free stereo reception is not possible, you can switch your
unit to MONO reception. In this case, select FM - MONO.
The muting function is always switched off for MONO reception,
allowing the unit to receive even very weak broadcast signals.
Adapting the antenna (antenna/cable)
If you receive broadcasts via broad band cable of a public or private
cable service, there may be high signal inputs at your antenna
terminal, which may in turn cause reception disturbances.
• If this is the case, press the MODE key and within 2 seconds 3 or
4 to switch on the input attenuator. CABLE appears on the display.
This reduces the antenna input sensitivity, thus reducing
disturbances. This setting is automatically stored.
Station memory
59 memory locations are available for storing stations.
• Tune to the station you want to store with the station search function
or manually.
• Press MEMORY.
– The station is stored at the next available memory location.
– The tuner software first checks the station memory for available
memory locations. If all the locations are occupied, MEM FULL
appears on the display for approx. 1.5 seconds.
– Assigning a station frequency to two different memory locations is
not possible. The selected station is stored at the lowest available
memory location, meaning that you do not need to enter a number
for memory locations.
– Every time the settings STEREO/MONO and ANTENNA/CABLE
are changed, they are automatically stored.
Storing stations
• If you want to store a station, press MEMORY.
– The first station which is stored is assigned to memory location 1,
the second station to memory location 2 and so on.
• If you want to move a stored station to another memory location,
press MEMORY.
– The station is always assigned to the first available memory
location.
• Pressing the key again assigns a station to the next available
memory location.
Example: You want to move your favourite station from memory
location '6' to memory location '1'.
• Select memory location '1'.
• Press CANCEL once.
– This deletes, or clears, memory location '1'. You can also press
MEMORY to move the station on location '1' to the next available
free memory location.
• Now select position '6', your favourite station, and then press
MEMORY. Your station is now stored on memory location '1'.
1 - 30
RADIO
RDS Radio Data System
Your tuner is an RDS tuner.
RDS (Radio Data System) stands for a new generation of radios that
provides the listener/user with more comfort and better reception in the
short term, but also opens up completely new information options for
MHz
the future. RDS-equipped receivers identify the tuned station (if it
transmits 'RDS signals') and indicate the name of the programme in the
display (e.g. BAYERN 3, SDR 3).
If you are tuned to an RDS station, the name of the station will be
indicated after a short time.
For more information, please see page 13.
Automatic station search
• To activate automatic station search (AUTO TUNING), press S
or T until the frequency display begins 'to run'; then release the
key.
– The search stops as soon as a station with sufficient reception
quality is found and tuned to precisely.
The
– Every time you begin a search, the unit automatically switches to
FM - STEREO.
– The frequency of the received station is indicated in MHz (FM).
– If the search stops, the 'AUTO COMPARE' function first verifies
whether the station which has been found is already stored in the
station memory. If this is the case, the memory location of the
station is displayed, as well as the name of the station, if it already
exists.
– Stations which are received with a weak field strength may be
skipped.
These can be tuned to manually.
• If desired, you can also interrupt the search by pressing S or
T.
Manual station search (manual tuning)
• Briefly press the S or T key to tune in the corresponding
direction in individual steps (25kHz).
• If you keep the key depressed, you can rapidly scan large
frequency ranges. When you release the key, AUTO TUNING is
automatically switched to. Muting is active during AUTO TUNING.
• If you briefly press one of the S or T keys, manual tuning is
automatically switched to.
RADIO
AUTO STORE function
This tuner is equipped with a comfortable way to store all stations
automatically.
• Press and hold down MEMORY until the frequency on the display
starts running and AS appears.
– The AUTO STORE function is started.
– The tuner will start searching from the actual frequency and stores,
MHz
first of all, all RDS stations that are not yet stored in the memory.
– Then it searches for the strongest non-RDS station and finally the
weak ones.
– This function ensures you that all stations with an acceptable
reception quality are stored in your station memory.
MHz • You can interrupt the AUTO STORE function by pressing MEMORY
again.
Calling up a stored station
• When you want to call up a stored station, press 1 or 2. The
stations are called up in ascending or descending order.
– The display shows the selected memory location number on the left,
and the unit switches to this memory location.
It is not possible to select a memory location which has not (yet)
been assigned to a station.
Example: Memory location 6 is not assigned to a station.
If you are situated at memory location number 5 and press once 2 the
unit will jump to memory location 7 (provided this location has been
assigned to a station).
Deleting a memory location
• If you want to delete a memory location to which a station is
assigned, first call up its number.
• Press 1 or 2 until you reach the station you want to delete.
• Press CANCEL.
– The memory location is deleted, and the memory location number
does not light up on the display anymore.
• Hold CANCEL down for 5 seconds if you want to delete all the
memory locations, for example after you move to another location.
– 'ERASE ?' appears briefly on the display.
• Keep the key depressed for an additional 5 seconds until the
display shows '87.5 MHz'. The station memory is deleted.
• If you now press one of the 1 or 2 keys, 'FREE' is shown on the
display.
• If you release the CANCEL key before these 5 seconds have elapsed,
the erase function of all memorized stations is not carried out.
indication lights up.
GRUNDIG Service
PA 5 - Turnit