Remote Control - Grundig PA 5 - Turnit Serviceanleitung

Allgemeiner Teil / General Section
DISPLAY
Display
The display indicates
– when receiving FM stereo stations
Q R
– during station search, during fast
cassette winding, during CD search
function.
B
– during CD play and cassette playback
forward.
A
– during cassette playback reverse.
– when the source TAPE is selected
∫
– indicates the TAPE reverse mode:
å
The tape stops at the end of each side.
∂
Playback (+ recording) of both cassette
sides; after which the tape stops at the
end of the second side.
∫
Continuous playback of both cassette
sides.
– lights up during the recording function,
rec
blinks during record pause.
– If the unit is optimally tuned to a radio
station.
– when the source CD is selected
;
– when the system is in CD or TAPE PAUSE
mode.
– when the sound is muted
MHz – for FM reception the frequencies are
indicated in MHz
########### – In this part of the display all relevant
messages are displayed.
– indicates the output signal
After selecting TUNER
S T to start the station search (AUTO TUNING) or
to advance the frequency step by step
(MANUAL TUNING).
1 / 2 to scroll through the station memory.
to switch the display indication between the
station name (RDS, or another name you
assign), RDS time, RADIOTEXT and station
frequency.
When pressing longer, the EDIT mode will be
entered in which station names can be given
with the following keys:
+ / – to go to a next/previous position on the
display (cursor)
3 / 4 to go through the alphabet,
0-9 and space symbol.
CANCEL - to clear the last name.
MEMORY to store a set station at the lowest respective
memory location. When pressing this key
longer, the AUTO STORE function will be
started.
CANCEL to delete individual memory locations or, if
desired, the entire memory contents (press more
than 10 seconds).
MODE to select the tuner mode function: then press
+ / – to select the desired waveband: FM
STEREO ™ FM MONO
Press 3 / 4 to select ANTENNA or CABLE.
Select CABLE to switch on the FM antenna
attenuator for reducing radio disturbance if your
system is connected to broadband cable, and
the reception signal is too strong.
9 PTY to enter the programme type mode.
then press + / – to call up the different
programme types.
1 - 28
rec
Changing the batteries
If the range of your infrared remote control seems to
decrease, or if certain individual functions can no longer
be carried out, you should replace the batteries. Two
mignon 1.5 Volt LR03 size AAA are required.
To change the batteries, open the compartment on the
back of the remote control. Ensure that the batteries are
inserted properly (note the markings in the compartment).
And in the interest of the environment: Remember that
batteries must always be disposed of properly.

REMOTE CONTROL

After selecting CD
to start playback or to switch the player to
2/PAUSE
PAUSE
to stop playback
9
to change the information on the display
between: the elapsed track time, the
remaining track time, the remaining disc time
and the total disc time.
to start forward or backward search. or to
S T
skip to next or previous tracks.
MEMORY
to call up the programming mode or to save
individual tracks.
press more than 2 seconds to review the
tracks in the programme.
CANCEL to omit individual tracks from the programme,
press more than 2 seconds (in STOP mode)
to delete the complete programme.
MODE to select the SHUFFLE and REPEAT mode:
then press + / – to switch the shuffle mode
on and off: SHUFFLE ON ™ SHUFFLE OFF
then press 3 / 4 to switch the repeat mode on
and off: REPEAT ON ™ REPEAT OFF.
REMOTE CONTROL
General functions
switches the unit to STAND BY.
y
+ / – adjusts the volume
mutes the speakers
SOURCE SELECTION
CD
selects the CD player.
kHz
TUNER selects the TUNER (radio).
MHz
TAPE selects the TAPE (cassette deck)
AUX selects the AUX (auxiliary) input.
DISPLAY to move the display up or down.
when pressed for more than 5 seconds it
changes the brightness of the display from 'nor-
mal brightness' to '50% brightness' to 'display off'.
MODE when pressed for more than 5 seconds it
switches the RF transmission on and off.
The display indicates ROOM B ON or ROOM B OFF.
Note: When the control unit is not placed on
top of the sound unit (placed in separate
places), it is not possible to switch the RF
transmission off (it is always on).
Sound functions
BASS to call up the BASS adjustment mode
then press + / – (within 2 seconds) to adjust
the bass tones
TREBLE to call up the TREBLE adjustment mode
then press + / – (within 2 seconds) to adjust
the high tones
MEMORY to store user sound presets at the lowest
memory location
POWER
switches POWER SOUND (Loudness)
SOUND on and off.
SOUND to scroll through the sound presets:FLAT,
CONTROL VOCAL, DISCO, JAZZ, USER1 and USER 2.
Note: FLAT, VOCAL, DISCO and JAZZ are pre-
defined presets.
CANCEL to delete user sound presets (when they are
selected).
After selecting TAPE
to start cassette playback in normal direction
2/PAUSE
and to switch the cassette deck to PAUSE.
to start cassette playback in reverse direction.
1
to stop all cassette functions.
9
S T When the unit is in STOP mode: fast forward or
backward.
When pressed during playback: MUSIC
SEARCH forward (to the beginning of the next
track) or backward (to the beginning of the
current track) Maximum 15 tracks can be
skipped.
to switch the display indication between the
COUNTER (tape counter) and TIME (real time in
minutes and seconds).
RECORD
press more than 2 seconds to start the
recording function.
CD COPY press more than 2 seconds to start the CD-
COPY function (recording from CD to cassette).
MEMORY to store a tape position in the memory. Pressing
again will clear the stored tape position.
CANCEL to set the tape counter to zero: 0000.
MODE to select the Dolby NR and reverse selection
mode:
then press + / – to switch Dolby Noise
Reductions system on or off: DOLBY ON ™
DOLBY OFF
Press 3 / 4 to select the desired reverse mode:
REVERSE OFF å ™ AUTOREVERSE ∂ ™
CONT. PLAY ∫
REVERSE OFF å – the tape stops at the end
of each side.
AUTOREVERSE ∂
– playback (+ recording) of
both cassette sides; after which the tape stops
at the end of the second side.
CONT. PLAY ∫ – continuous playback of
.
both cassette sides.
PA 5 - Turnit
GRUNDIG Service