Batavus X4 Betriebsanleitung Seite 9

and set the brightness in the same way. To exit,
press the Reset button.
Switching the display for different information
13.
and sequences (Zoom1/Zoom2)
Press the Zoom1 or Zoom2 button to switch the
display.
Display during training
A)
The values are continuously re-calculated and
displayed in accordance with the time. All current
training data are displayed together with the time
and the room temperature.
Display in Stop mode
B)
The values calculated during training are displayed
graphically. The time, room temperature and the
training data entered previously are displayed.
Note on the LOOP function
The actual number of watts and the distance
covered are shown in Display 1. The distance
point (round) where you are currently located will
blink. If a distance was specified (in Display 2), the
display is in increments of 1 kilometer. Without a
preset value, the point changes every 800 meters.
Storing personal data (Save)
14.
Personal data for six people can be stored in
the Stop function on a USB memory stick by
pressing the Save button. Every USB stick stores
a maximum of 30 records (preset values for items
such as time, distance or calories) per person.
The number is shown in Display 1, e.g., Sav 13.
The corresponding data are shown on the right-
hand display. At 30 saves, the first data saved are
automatically erased and the number 30 displayed.
Press the Reset button to return to the last training
mode.
Stored values 1-30 (Recall)
15.
The last record used for the user is shown in
Display 1 when the Recall button is pressed in Stop
mode. Press the button again to select other records
(counting downward). Press the Reset button to
switch the display to the training program.
Sleep function
16.
If you are not training and no button has been
pressed, the control panel automatically goes
into Sleep mode after four minutes. The day
of the week, the date and the name Batavus (in
marquee mode) are shown on Display 1. The room
temperature and the time of day are shown on
Display 2.
TRAINING PREPARATION
The unit is not plugged in.
A.
First insert the connector for the transformer
1.
cord into the receptacle on the back of the unit.
Then insert the large plug into a power outlet.
A long signal tone sounds, and all segments
2.
of both displays are shown briefly for testing
purposes.
The control panel then displays the name
3.
Batavus and a control number for a few seconds
O W N E R ' S M A N U A L
before switching to the input mode. The year will
blink. See the "Calendar/Time" section for the
input sequence.
The unit is in Sleep mode (already plugged in).
B.
The temperature, etc., is being displayed.
1.
Press the Rest button to switch to input mode.
2.
Press the Plus/Minus buttons to select a
3.
program.
The input sequence is explained in the program
descriptions.
ENTERING THE CALENDAR DATA
AND TIME OF DAY
Calendar:
Possible inputs:
Month Day
01-12 01-31
The day of the week is calculated and displayed
automatically using the date you enter.
MON Monday
TUE Tuesday
WED Wednesday
THU Thursday
FRI Friday
SAT Saturday
SUN Sunday
The control panel must be in the input mode.
1.
The year is blinking on Display 1.
•
Press the Plus/Minus buttons to make a
selection.
•
Press the Mode button.
The day of the month will blink.
•
Press the Plus/Minus buttons to make a
selection.
The month number will blink.
•
Press the Plus/Minus buttons to make a
selection.
•
Press the Mode button.
The hour will blink on Display 2.
•
Press the Plus/Minus buttons to make a
selection.
•
Press the Mode button.
The minutes will blink.
•
Press the Plus/Minus buttons to make a
selection.
•
Press the Mode button.
If there is no USB stick inserted for the user
data, you may now select one training program.
If a USB stick is inserted, the user data are now
entered. The users U1 -- U6 are displayed briefly
in accordance with the selected USB stick. Then,
the 8-digit number for the user name will blink.
G B
•
B A T AV U S
Year
00-50
9