Storage And Transport; Repair & Ordering Spare Parts; Service Information - Scheppach Acs4000 Originalbetriebsanleitung

27. Hold a cloth in front of the connection thread
(14). Turn the pressure control (3) to position 1
for 5 seconds. This preserves the device. Turn the
pressure control (3) to position 0 (off).
28. Unplug the mains plug from the socket.
Cleaning the inlet valve (Fig. 8)
NOTE: If problems with the paint suction cannot be
eliminated, clean the inlet valve 26 or replace it if nec-
essary.
1. Disconnect the suction hose (2) the device.
2. Remove the inlet valve (26) using an open-end-
ed spanner.
3. Remove the O-ring (25), ball (24), washer (23) and
spring (22) (see Fig. 7).
4. Clean the parts thoroughly using suitable cleaning
agents. Replace them if necessary.
5. Grease the O-ring (25).
6. Insert the parts of the intake filter (26) (see Fig. 7).
7. Turn the inlet valve (26) back into the device.
Tighten using an open-ended spanner.
Cleaning the connection thread
If a poor spray pattern persists after cleaning the noz-
zle, clean the connection thread (14).
1. Remove the high-pressure hose (12) from the con-
nection thread (14) using an open-ended spanner.
Counter the nut of the connection thread (14) with
a second open-ended spanner.
2. Loosen the fastening screw (27) with a Phillips
screwdriver (not supplied).
3. Loosen the Allen screw (28) with a 2 mm Allen
key (not supplied).
4. Remove the connection thread (14) using an
open-ended spanner.
5. Clean the connection thread (14) using suitable
cleaning agents. Replace it if necessary.
6. Screw the connection thread (14) back into the de-
vice and tighten it using an open-ended spanner.
7. Turn the fastening screw (27) with a Phillips
screwdriver to tighten again.
8. Turn the Allen screw (28) with a 2 mm Allen key
to tighten again.

14. Storage and transport

Store the product and its accessories in a dark, dry and
frost-free place that is inaccessible to children.
The optimum storage temperature lies between 5 and
30 ˚C.
Store the product in its original packaging. Cover the
product to protect it from dust or moisture. Store the
operating manual with the product.
15. Repair & ordering spare parts
After repairs or maintenance, make sure that all safe-
ty-related parts are installed and are in perfect con-
dition. All parts which may cause injury must be kept
where they are inaccessible to children or others.
Attention: According to the German Product Liability
Act, no liability is accepted for damage caused by im-
proper repairs or by not using original spare parts.
Such work should be performed by a customer service
centre or an authorised specialist. The same applies to
accessory parts.
Spare parts and accessories can be obtained from our
Service Centre. To do this, scan the QR code on the
front page.
Connections and repairs
Connections and repair work on the electrical equip-
ment may only be carried out by electricians.
Please provide the following information in the event
of any queries:
• Type of current for the motor
• Machine data - type plate
• Motor data - type plate
Important note in the case of repairs:
When returning the product for repair, for safety rea-
sons, ensure that it is free of paint when it is sent to the
service centre.
15.1 Ordering spare parts
Please provide the following information when order-
ing spare parts:
• Model designation
• Item number
• Type plate data

15.2 Service information

With this product, it is necessary to note that the fol-
lowing parts are subject to natural or usage-related
wear, or that the following parts are required as con-
sumables.
Wearing parts*: High-pressure hose, HEA filter, noz-
zle, paint spray gun
www.scheppach.com GB | 35