Werbung
Verfügbare Sprachen
Verfügbare Sprachen
6.
To adjust the spray pattern, turn the nozzle cap (1)
on the round spray nozzle (16) clockwise.
11.8 Setting the round or mist spray pattern (Fig.
13)
• To set a round spray, turn the nozzle cap (1) on the
round spraying valve (16) anti-clockwise.
• To set the mist spray function, turn the nozzle cap (1)
on the round jet nozzle (16) clockwise.
12. Transport
Note
To prevent damage to the container (13) during trans-
port, always lift the pressure sprayer and do not drag it
across the floor.
Transport during use
Note
Ensure that pressure sprayer is always upright. Only
then can the pressure sprayer function properly.
1.
Hang the pressure sprayer over your shoulder us-
ing the carrying strap (12).
Transport after use
1.
Press the handle (15) down through the recess and
turn the handle (15) clockwise as far as it will go.
2.
Pull the safety valve (14) up as far as it will go to
release the residual pressure in the container (13).
3.
Hang the spray wand (5) with the holding device
(19) into the holder (20).
4.
Carry the pressure sprayer by the handle (15) or
using the carrying strap (12).
13. Cleaning (Fig. 10)
• Empty the container after each use.
• We recommend that you clean the product directly
after every use.
• Clean the product at regular intervals using a damp
cloth and a little soft soap. Do not use any cleaning
products or solvents; they could attack the plastic
parts of the product.
• Always wear suitable personal protective equip-
ment.
13.1 Cleaning the nozzle (16, 17)
Note
Do not blow the nozzles clear with your mouth if they
are blocked.
24 | GB
• Unscrew the nozzle.
• Clean the nozzle under running water.
• To clean a blocked nozzle, use a needle to pierce
the nozzle.
13.2 Cleaning the pressure sprayer
1.
Place the product on a level, even surface.
2.
To release the residual pressure in the container
(13), pull the safety valve (14) upwards as far as
it will go.
3.
Only then open the container (13) by turning the
screw connection (21) anti-clockwise.
4.
Pull the pump (11) out of the container (13) using
the handle (15).
5.
Remove the spray wand (5) as described in8.1
Assembly.
6.
Rinse the pressure sprayer and the lines with wa-
ter.
7.
Clean the surfaces with a damp cloth.
8.
Dry the product with a cloth after cleaning.
13.3 Cleaning the suction hose (6)
1.
Place the product on a level, even surface.
2.
To release the residual pressure in the container
(13), pull the safety valve (14) upwards as far as
it will go.
3.
Loosen the union nut (7).
4.
Pull the suction hose (6) out of the container (13).
5.
Remove the dirt filter from the suction hose (6) and
clean the dirt filter and the suction hose (6) under
running water.
6.
Fit the dirt filter onto the suction hose (6).
7.
Push the suction hose (6) into the container (13).
8.
Screw on the union nut (7) hand-tight.
14. Storage
Note
Never leave the pressure sprayer with a full, pressur-
ised container unattended for long periods of time.
1.
Release any residual pressure in the container af-
ter use. To do this, pull up the knob of the safety
valve until you no longer hear any hissing.
2.
Remove any residual spray agent from the con-
tainer and lines.
3.
Clean the appliance thoroughly and allow it to dry
before storing it for the winter. This prevents dam-
age caused by frost.
www.scheppach.com
Werbung
