Residual Risks; Assembly - Scheppach Hc24X Originalbetriebsanleitung

WARNING
The product is not designed for use in potentially explo-
sive atmospheres. Use in such environments is only
permitted if suitable additional measures are taken to
ensure safety. Please consult a specialist or refer to the
relevant regulations before using the product in a poten-
tially explosive atmosphere.
• The product shall not be operated by persons (includ-
ing children) with reduced physical, sensory or mental
abilities or who have inadequate experience or knowl-
edge.
• Cleaning and user maintenance must not be carried
out by children.
• Keep the product away from rain and moisture. Water
penetrating the product increases the risk of an elec-
tric shock.
• Avoid using the product at temperatures below +5°C.
• Do not leave the product unattended.
CAUTION
Operate the product for a short time only. Long, uninter-
rupted operation of more than 10 min. overheats the
product. Switch off the product immediately and let it
cool down for at least 10 mins
DANGER
Danger of injury!
Do not allow the items to be inflated above the pressure
intended for them. These can burst and lead to injuries
and/or material damage.
• Do not exceed the permissible power range of the
compressor. Do not inflate truck, tractor or other large
tyres.
• Do not work on materials that are or could be poten-
tially flammable or explosive.
• Never misuse the product.
• Always keep the product clean, dry and free from oil
or grease. Remove dust after each use and before
storage.
• Never use petrol or other flammable liquids to clean
the product! Vapours remaining in the product can be
ignited by sparks and cause the product to explode.
• Remain attentive at all times! Always pay attention
to what you are doing and always use common
sense. Never use the product if you are unable to
concentrate or feel unwell.
• Avoid over-stressing the piping system by using flexi-
ble hose connections to prevent kinking.
• In case of pressures above 7 bar, it is recommended
to equip supply hoses with a safety cable (e. g. a wire
rope).
• Do not touch the hot components of the product!
• Ensure that all hoses and fixtures are suitable for the
maximum permissible working pressure of the com-
pressor.

Residual risks

The product has been built according to state-of-the-
art and the recognised technical safety rules.
However, individual residual risks can arise during
operation.
• Health hazard due to electrical power, with the use of
improper electrical connection cables.
• Furthermore, despite all precautions having been met,
some non-obvious residual risks may still remain.
• Residual risks can be minimised if the "Safety Instruc-
tions" and the "Intended Use" together with the operat-
ing instructions as a whole are observed.
• Prevent the product being unintentionally started up.
• Keep your hands away from the working area when
the product is in operation.
• Comply with the stipulated maintenance and safety in-
structions in the operating instructions.
WARNING
This power tool generates an electromagnetic field
during operation. This field can impair active or passive
medical implants under certain circumstances. In order
to prevent the risk of serious or deadly injuries, we rec-
ommend that persons with medical implants consult
with their physician and the manufacturer of the medical
implant prior to operating the power tool.
8

Assembly

ATTENTION
Always make sure the product is fully assembled
before commissioning!
WARNING
Danger of injury!
Do not insert the mains plug into the socket until you
are ready to use the product.
Required tool:
• 2x 10 mm open-ended spanner/socket spanner*
• Open-ended spanner/socket spanner, size 13 mm*
• Open-ended spanner/socket spanner, size 17 mm*
* = may not be included in the scope of delivery!
8.1 Fitting the wheels (6) (Fig. 3)
1. Place a pad on the floor to avoid damage to the prod-
uct.
2. Tip the product slightly onto its side.
3. Fit one wheel (6) into the assembly holes provided on
the base frame.
4. Fit the wheel (6) to the base frame using a screw (6a)
and secure it with a spring washer (6b) and a nut (6c).
Use an 13mm and an 17mm open-ended spanner/
socket spanner.
5. Repeat the process on the opposite side.
8.2 Fitting the foot (7) (Fig. 4)
1. Place the product on a level, even surface.
www.scheppach.com GB | 23