Scheppach HC26Si Originalbetriebsanleitung Seite 25

• Check the product and accessory parts for transport
damage. In the event of complaints the carrier must
be informed immediately. Later claims will not be
recognised.
• If possible, keep the packaging until the expiry of the
warranty period.
• Familiarise yourself with the product by means of the
operating manual before using for the first time.
• With accessories as well as wearing parts and re-
placement parts use only original parts. Spare parts
can be obtained from your specialist dealer.
• When ordering please provide our article number as
well as type and year of manufacture for the product.
m WARNING!
The product and the packaging material are not
children's toys! Do not let children play with plas-
tic bags, films or small parts! There is a danger of
choking or suffocating!
9. Before commissioning
• Before connecting, make certain that the data on the
type plate matches with the mains power data.
• Check the product for transport damage. Report
any damage immediately to the transport company
which was used to deliver the compressor.
• Install the compressor near the point of consump-
tion.
• Long air lines and supply cables (extension cable)
should be avoided.
• Ensure that the intake air is dry and dust-free.
• Do not install the compressor in a damp or wet room.
• Operate the compressor only in suitable areas (well
ventilated, ambient temperature +5°C to 40°C).
There must be no dust, acids, vapours, explosive
gases or inflammable gases in the room.
• The compressor is designed to be used in dry rooms.
It must not be used in areas where splashed water
is present.
• The compressor may only be used outdoor briefly
when the ambient conditions are dry.
• The compressor must always be kept dry and must
not be left outdoors after work is complete.
10. Assembly and operation
m Attention!
Always make sure the product is fully assembled
before commissioning!
You require the following for assembly:
1x socket spanner 12 mm, open-end spanner 13 mm
and 17 mm. (not included in the scope of delivery)
10.1 Fitting the transport handle (Fig. 3)
• Fit the supplied transport handle (1) as shown.
10.2 Fitting the wheels (fig. 4)
• Fit the wheels (10) provided as shown.
10.3 Fitting the foot (Fig. 5)
• Fit the foot (12) provided as shown in.
10.4 Mains power connection
• The compressor is equipped with a mains cable
with an earthed plug. This can be connected to any
220‒240 V~ 50 Hz protective contact socket, with
fuse protection of at least 16 A.
• Before you use the machine, make sure that the
mains voltage is the same as the operating voltage
and the machine power on the rating plate.
• Long supply lines, as well as extensions, cable
drums etc. cause voltage drop and can prevent the
motor from starting.
• At low temperatures below +5 °C, sluggishness may
make starting difficult or impossible.
10.5 On/Off switch (fig. 1)
• Pull the on/off switch (3) upwards to switch on the
compressor.
• Press the on/off switch (3) down to switch off.
10.6 Adjusting the pressure (fig. 1)
• The pressure at the manometer (5) is adjusted with
the pressure regulator (6).
• The adjusted pressure can be drawn from the quick
coupling (8).
10.7 Setting the pressure switch (fig. 1)
• The pressure switch (2) is set at the factory.
Cut-in pressure approx. 6 bar
Cut-out pressure approx. 8 bar
10.8 Fitting the compressed air hose (fig. 1)
• Connect the plug-in nipple of the compressed air
hose (not included in the scope of delivery) to one
of the quick-connect couplers (8). Then connect
the compressed air tool to the quick coupling of the
compressed air hose.
www.scheppach.com GB | 25