Scheppach HC24V Originalbetriebsanleitung Seite 19

ATTENTION
Signal word to indicate a potentially hazard-
ous situation which, if not avoided, could re-
sult in product or property damage.
1 Introduction
Manufacturer:
Scheppach GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Note:
In accordance with the applicable product liability laws,
the manufacturer of this product assumes no liability for
damage to the product or caused by the product arising
from:
• Improper handling
• Failure to comply with the operating manual
• Repairs carried out by third parties, unauthorised spe-
cialists
• Installing and replacing non-original spare parts
• Improper use
• Failures of the electrical system due to failure to ob-
serve the national electrical requirements and regula-
tions.
Note:
The operating manual is part of the product and contain
important information for safe, proper and economical op-
eration. Please also observe the applicable national regu-
lations. Read all operating and safety instructions careful-
ly before use and only use the product as described.
Keep the manual and pass it on when you give the prod-
uct to someone else.
2 Proper use
The compressor is used to generate compressed air for
pneumatically powered tools that can be operated with an
air rate of up to 180 l/min. (e.g. tyre inflators, air blow
guns, paint spray guns). Due to the limited air output it is
not possible to use the compressor to drive tools with very
high air consumption (for example orbital sanders, die
grinders and hammer screwdrivers).
The compressor may only be operated in a dry and well
ventilated indoor space.
The product may only be used in the intended manner.
Any use beyond this is improper. The user, not the manu-
facturer, is responsible for damages or injuries of any type
resulting from this.
An element of the intended use is also the observance of
the safety instructions, as well as the assembly instruc-
tions and operating information in the operating manual.
Persons who operate and maintain the product must be
familiar with the manual and must be informed about po-
tential dangers.
The liability of the manufacturer and resulting damages
are excluded in the event of modifications of the product.
The product may only be operated with original parts and
original accessories from the manufacturer.
The safety, operating and maintenance specifications of
the manufacturer, as well as the dimensions specified in
the technical data, must be observed.
Please note that our products were not designed with the
intention of use for commercial or industrial purposes. We
assume no guarantee if the product is used in commercial
or industrial applications, or for equivalent work.
3 Product description (Fig. 1-9)
1. On/off switch
2. Transport handle
2a. Screw
2b. Holder
3. Pressure regulator
3a. Manometer
4. Quick coupling
5. Safety valve
5a. Drain nut
6. Pressure vessel
6a. Drain plug
(condensation water)
7. Foot
7a. Screw
7b. Washer (large)
7c. Washer (small)
7d. Spring washer
7e. Nut
8. Compressed air accessory set 13 pcs.*
(not shown)
* = may not be included in the scope of delivery!
4 Scope of delivery (Fig. 1, 2)
Item Quantity Designation
2a. 4 x
7. 3 x
7a. 3 x
7b. 3 x
7c. 3 x
7d. 3 x
7e. 3 x
8. 1 x
1 x
1 x
* = may not be included in the scope of delivery!
5 Unpacking
WARNING
The product and the packaging material are not
children's toys!
Do not let children play with plastic bags, films or
small parts! There is a danger of choking or suffo-
cating!
• Open the packaging and carefully remove the product.
• Remove the packaging material, as well as the pack-
aging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the product and accessory parts for transport
damage. Immediately report any damage to the trans-
port company that delivered the Product. Later claims
will not be recognised.
www.scheppach.com
Screw
Foot
Screw
Washer (large)
Washer (small)
Spring washer
Nut
Compressed air accessory set 13 pcs.*
(not shown)
Compressor
Operating manual
GB | 19