Network Settings - InoTec CLS 24.1 - Power Montageanleitung Und Bedienungsanleitung

CLS 24.1/SV Montage- und Betriebsanleitung
10.4.1
Nach Betätigung des Reset-Schalters am InoWeb-Modul
erscheint folgender Text im Terminalbildschirm:
Firmware
Applikation (InoWeb)
Aktuelle Netzwerkeinstellungen
Eigene IP Adresse (Beispiel)
Netzwerkmaske (Beispiel)
Gateway (Beispiel)
Baudrate für Setupdialog
Eingestellte Seriennummer
Feste Ethernet MAC Adresse
Timeout Setupdialog
Voll-/Halbduplex
10.4.1.1. Netzwerkeinstellungen
Um die Netzwerkeinstellungen zu ändern, muss inner-
halb der nächsten fünf Sekunden eine Taste betätigt
werden, ansonsten startet die Applikationssoftware. In
diesem Fall muss zur Programmierung ein erneuter Reset
durchgeführt werden.
m eingeben um Parameter zu
modifizieren
Masterpasswort eingeben
(Netsilicon)
Alle Parameter auf Vorgabe
Zurücksetzen? (y)es / (n)o
Yes = Parameter per
DHCP vom Server beziehen (Standard Einstellung)
Eigene IP Adresse (Beispiel)
Netzwerkmaske (Beispiel)
Adresse des Gateway ins (Beispiel)
Internet z.B. ISDN oder DSL- Router.
Masterpasswort ändern?
Baudrate für diesen Setupdialog
Seriennummer ändern / keine Eingabe
Timeout Setupdialog
Ethernetverbindung
zum Hub, Switch ....Sollte immer
"phy Default" sein = automatisch
42
NET+WORKS Version 6.0
Copyright (c) 2003, NETsilicon, Inc.
PLATFORM: connectme_lsk
APPLICATION: INOWeb APP
SetupDialog 1.3
-------------------------------------------------------------------
NETWORK INTERFACE PARAMETERS:
IP address on LAN is 192.168.100.200
LAN interface's subnet mask is 255.255.255.0
IP address of default gateway to other networks is 192.168.100.201
HARDWARE PARAMETERS:
Serial channels will use a baud rate of 9600
This board's serial number is N99999999
This board's MAC Address is 00:40:9D:27:A0:49
After board is reset, start-up code will wait 5 seconds
Default duplex setting for Ethernet connection: phy Default
--------------------------------------------------------------------
APPLIKATIONS PARAMETER:
Neues Password for WEB-Zugriff (max. 9 character)
Benutzername=WEBUSER Password:*******
Aktuelle Ortsangabe: Technical Training 2007
--------------------------------------------------------------------
Press any key in 5 seconds to change these settings.
Press A to Accept the settings, or M to Modify?m
Enter the root password: **********
Reset configuration to default values (Y/N)?
For each of the following questions, you can press <Return> to
select the value shown in brackets, or you can enter a new value.
NETWORK INTERFACE PARAMETERS:
Should this target obtain IP settings from the network?[N]
Static IP address [192.168.100.101]?
Subnet Mask IP address [255.255.255.0]?
Gateway address IP address [192.168.100.50]?
SECURITY PARAMETERS:
Would you like to update the Root Password?[N] n
HARDWARE PARAMETERS:
Set the baud rate of Serial channels[9600]?
The new baud rate is 9600
The baud rate will be changed on next power up
Please set the baud rate for your terminal accordingly
Each development board must have a unique serial number
Set the board's serial number[I00000003]?
How long (in seconds) should CPU delay before starting up[5]?
Normally the board will automatically negotiate with the network
hub(or switch) to determine the Ethernet duplex setting, however
some hubs do not support autonegotiation.
ernet driver can force the PHY to half duplex, force it to full
duplex, or allow the PHY to use its default setting (usually half
duplex).
Default Ethernet duplex setting (Full, Half, or phy Default)?[phy
Default]
Saving the changes in NV memory...Done.
CLS 24.1/SV Mounting and Operating Instructions
10.4.1
After activating the reset switch on the InoWeb module,
the following text appears in the terminal screen:

10.4.1.1. Network settings

To change the network settings, you must press any key
within five seconds otherwise the application software
starts. If this happens, you need to perform another reset
to start programming.
n
In this case, the Eth-
should always be "phy Default"= automatic
referring to the firmware
name of the software
Current network settings
own IP address (example)
subnet mask (example)
gateway (example)
baud rate for setup dialog
set serial number
firm Ethernet MAC address
timeout setup dialog
full/half duplex
enter m to
modify the settings.
enter master password
(Netsilicon)
reset all settings to
default values.
Reset? (y)es / (n)o
Yes = obtain settings
per DHCP from server (default setting)
own IP address (example)
subnet mask (example)
gateway address to (example)
the Internet e.g.
ISDN or DSL router.
change master password?
baud rate for this setup
change serial number /
no input
timeout setup dialog
Ethernet
connection to hub, switch ....