nemaxx P6 Bedienungsanleitung Seite 8

• Paper products, cardboard, or partic�e-
board;
• Garbage;
• Anima� remains or manure;
• Lawn c�ippings or yard waste;
• Waste petro�eum products;
• Coa�;
• Construction or demo�ition debris;
• Rai�road ties or pressure-treated wood;
• Materia�s containing asbestos, p�astic,
rubber (inc�uding tires)
• Petro�eum products such as paints, paint
thinners, aspha�t products
BURN�NG THESE MATER�ALS MAY
RESULT �N RELEASE OF TOX�C FUMES OR
RENDER THE HEATER �NEFFECT�VE AND
CAUSE SMOKE
Do not store wood pe��et fue� or other 昀椀re
starting materia�s on f�oor protector, underneath
stovepipe, or anywhere within minimum
c�earances from combustib�e surfaces speci昀椀ed
on page 7.
Wood pe��et fue� shou�d be stored in a dry, we��
venti�ated area.
CAUT�ON: DO NOT store unused pe��ets
in the stove for future use as they may
co��ect moisture. Using wet or damp pe��ets
may resu�t in ignition di昀케cu�ty, incomp�ete
combustion, and the potentia� for a hopper
昀椀re.
OPERATING PRECAUTIONS
WARN�NG: HOT WH�LE �N OPERAT�ON. DO
NOT TOUCH THE STOVE. KEEP CH�LDREN,
CLOTH�NG AND FURN�TURE AWAY. CONTACT
MAY CAUSE SK�N BURNS.
CAUT�ON: ENSURE THAT THE F�RE POT
AND THE PAN UNDERNEATH ARE CLEAN AND
�N THE PROPER OPERAT�NG POS�T�ON
BEFORE US�NG THE STOVE.
WARN�NG: NEVER USE GASOL�NE,
GASOL�NE-TYPE LANTERN FUEL, KEROSENE,
CHARCOAL L�GHTER FLU�D, OR S�M�LAR
L�QU�DS TO START OR 'FRESHEN UP' A F�RE
�N TH�S HEATER. KEEP ALL SUCH L�QU�DS
WELL AWAY FROM THE HEATER WH�LE �T �S
.
�N USE
PAINT CURING
To a��ow the paint to bond durab�y to the stove,
start by running the stove on P1 Maximum
Power for at �east 60 minutes.
Provide cross venti�ation to e�iminate odors or
smoke cause by this curing process.
OPERATING PROCEDURE: TURN ON
STOVE
NOTE: �f the disp�ay screen indicates that
the stove is "Switching O昀昀" the stove can not be
interrupted. The Disp�ay Message wi�� high�ight
to indicate that the state wi�� not be changed.
On�y once the "Switching O昀昀" cyc�e has 昀椀nished
and the exchanger has coo�ed can the stove be
turned back on again.
1. P�ug power cord into socket on the rear
bottom of stove and press the red ON/OFF
togg�e switch above it to ON. See Figure 16.
NOTE: TO PREVENT STOVE FROM BE�NG
OPERATED, TURN OFF RED POWER SW�TCH
ON BOTTOM, REAR OF STOVE.
2. Make sure that sea�s on the ash drawer and
door are in good condition. �f the stove has
never been run before, add a handfu� of
pe��ets direct�y to the 昀椀re pot. C�ose the ash
drawer and doors secure�y, and check that
a�� side pane�s are a�� proper�y insta��ed.
NOTE: DO NOT USE GRATES, �RONS, OR
ANY OTHER METHODS OF SUPPORT�NG
WOOD PELLET FUEL. ONLY THE F�RE POT
SPEC�F�C TO YOUR MODEL OF STOVE MAY
BE USED.
3. Open the hopper. Ensure that there area
su昀케cient number of pe��ets to satisfy your
heating requirements. C�ose the hopper.
4. Depress the power button
The stove wi�� begin to automatica��y pro-
gress through the fo��owing stages:
• C�eaning Cyc�e: The 昀椀re pot draws dust, ash,
& remnants out.
• Feeding Cyc�e: Pe��ets wi�� be transported
from the Pe��et Hopper into the 昀椀re pot by the
auger. This can take 5 to 15 minutes
depending on the mode� of stove.
• Lighting Cyc�e: The e�ectrica��y powered hot
surface igniter wi�� run the entire �ighting
cyc�e and for a coup�e minutes after the
stove reaches stabi�izing and begin
combustion of the pe��ets in the 昀椀re pot. The
heater wi�� remain in the Lighting Cyc�e unti�
the exhaust smoke reaches a designated
temperature.
EN
for 3 seconds.
8