nemaxx P6 Bedienungsanleitung Seite 12

Press to increase the temperature which
the stove is intended to heat the room to. This
va�ue is disp�ayed in the top right of the Mu�ti
function Disp�ay screen as ## 0°C.
Press to decrease the temperature which
the stove is intended to heat the room to. This
va�ue is disp�ayed in the top Right of the Mu�ti
function Disp�ay screen as ## °C.
Press and ho�d whi�e the stove is in
'We�come to Use' to manua��y turn the auger
motor to prime the Auger with pe��ets when
needed.
�n the settings menus, tap to switch
between on-screen options.
Pressing the rate se�ect wi�� togg�e between
four con昀椀gurab�e heating presets. The current�y
set preset is avai�ab�e in the top midd�e of the
mu�ti function disp�ay screen as P#.
• P1 [High Power] Settings
• P2 [Medium-P�us Power] Settings
• P3 [Medium Power] Settings
• P4 [Low Power] Settings
Press and ho�d the Settings button for 2
seconds to enter the set up menu.
Press the settings button at anytime to exit the
set up menu.
• Eco Mode: There are two ECO Setting swich
can be se�ected which wi�� conserve wood
pe��ets whi�e maintaining the desired
temperature. Pressing the ECO button wi��
a��ow you to togg�e whether a speci昀椀c eco
setting is enab�ed, or to turn o昀昀 the feature
entire�y.
▶ ECO1: The stove shuts o昀昀 when the
desired temperature has been reached.
The stove wi�� turn back once the room
coo�s to a factory set temperature.
▶ ECO2: The stove turns to Minimum
power preset P4 when the desired
temperature has been reached. The
stove wi�� turn on to higher power
Settings once the room coo�s to a
factory set temperature.
• Preset con昀椀gurations: There are four
se�ectab�e con昀椀gurations which adjust the
Speeds of the combustion fan and the room
air circu�ation fan. Pressing the preset
con昀椀guration button wi�� a��ow you to togg�e
whether a speci昀椀c preset con昀椀guration is
enab�ed, or to turn o昀昀 the feature entire�y.
• P1 [High Power] Settings
• P2 [Medium-P�usPower] Settings
• P3 [Medium Power] Settings
• P4 [Low Power] Settings
MANUAL STOVE OPERATION
TO ADJUST THE AUGER (PELLET DROP RATE)
Cyc�e using the Rate Se�ect button between
settings P1, P2, P3, P4. Rates are out�ined
be�ow:
P1: [High] pe��et drop rate
P2: [Medium-P�us] pe��et drop rate
P3: [Medium] pe��et drop rate
P4: [Low] pe��et drop rate
Note: �f necessary, press and ho�d the "Time"
button for 2-5 seconds to get the auger to spin.
TO ADJUST THE FANS
1. Press and ho�d the Settings button for 2
seconds.
2. Press the Con昀椀rm button to cyc�e to each of
the Pe��et Drop Rate Settings.
3. Adjust the "S" for Venting Fan and "F" for
b�ower fan Settings using the Up and Down
Se�ectors buttons.
4. Use the Time button to switch between "S"
and "F".
Note: the �ower the setting, the s�ower the fan.
On�y change settings by a few numbers at a
time.
5. Press the Settings button to go back to home
screen.
TO CHANGE THE TIME (RUNS ON 24-HOUR
CLOCK
1. Press and ho�d the Settings button for 2
seconds.
2. Press the Con昀椀rm button to cyc�e to modify
C�ock.
3. Use the Time button to switch between
hours and minutes.
4. Use the Up and Down Se�ector buttons to
change the current se�ection.
5. Press the Settings button to go back to
home.
TO PROGRAM AUTOMATIC ON/OFF
1. Press and ho�d the Settings button for 2
seconds.
2. Cyc�e through the Settings using the
Con昀椀rm button unti� days of the week are
visib�e.
3. Use the Time button to change between
days.
4. Use the Up and Down Se�ector Buttons to
adjust if you want the stove ON/OFF each
day.
Note: Ta�� box is for ON; Short box is for OFF.
EN
12