nemaxx P6 Bedienungsanleitung Seite 16

The remaining pe��ets in the burner hopper wi��
continue to burn after the stove has coo�ed down
and the error code has been removed.
Otherwise, the stove must be restarted for
norma� operation.
3. Fuse: A fuse on the rear of the device
protects the stove from power surges.
PELLET STOVE CLEANING SCHEDULE
DAILY CLEANING
Step 1: Shut down the stove and �et it coo�
comp�ete�y.
Step 2: Grab your ash vacuum to remove ash
and debris from the 昀椀re pot and surrounding
area, as we�� as any pi�es of ash or debris that
you see.
Step 3: Lift up and remove 昀椀re pot – be certain
this area is c�ear of debris. Vacuum under the 昀椀re
pot, taking specia� care to vacuum the airway
under the 昀椀re pot.
Step 4: Grab your c�eaning too� and move to the
昀椀re pot. Scrape any debris out of the 昀椀re pot,
making sure that a�� of the ho�es in the 昀椀re pot
are free from any bui�dup.
Step 5: Wipe down the g�ass. Never c�ean the
g�ass with coo� water or c�eaner when the g�ass
is sti�� warm, since this can cause the g�ass to
crack. The method we recommend requires a
damp paper towe� or c�oth. Dab it on to coo�ed
ashes and then wipe down the g�ass starting
from the top.
Step 6: Certain mode�s have ash drawers. �t is a
good idea to empty it every time you c�ean your
stove. You can use an ash vacuum to c�ean the
ashes out of the drawer.
Step 7: The c�eaning rods shou�d be used dai�y
after the stove has coo�ed down. These are
c�eaning inside of the exhaust where ash and
debris can bui�d up. When too much bui�dup
occurs, your stove wi�� not have the proper
amount of airf�ow.
WEEKLY CLEANING
Step 1: Recommend �etting the stove run out of
pe��ets so the hopper is empty. Vacuum out the
hopper. C�ean any dust out of the hopper and
inspect your auger.
Step 2: �f equipped, remove the ash drawer and
vacuum out the drawer. Then brush and scrape
away any s�ag and bui�d up. Make sure the area
under the drawer is a�so c�ean.
Step 3: �nspect Auger chute. �f you notice any
bui�d-up of creosote or pe��et dust, c�ean the
chute with a wire brush.
EVERY OTHER WEEK
Go outside, and visua��y inspect the termination
cap on the exhaust. Make sure anima�s are not
trying to make it their home and check for any
bui�dup of ash on the grate.
AT LEAST ONCE A MONTH
Step 1: Use a c�eaning brush to c�ear out the air
in�et, �ocated beneath the 昀椀re pot going towards
the back of the stove; exact p�acement and size
wi�� vary from mode� to mode�.
Step 2: There are four exhaust ports at the top
of the burn chamber. Use a c�eaning brush to
c�ear out the air exhaust ports in your burn
chamber. Verifying they are c�ear wi�� ensure
optima� air f�ow in the chamber.
EVERY TWO (2) TONS OF PELLETS, OR
EVERY OTHER MONTH
�nspect the c�ean out tee. Remove any ash that
has bui�t up and resea� the connection if
necessary.
ANNUALLY
• �t is important to remove the combustion fan,
use a wire brush on creosote, and vacuum
debris. This is important for under the fan
and on the fan itse�f. When you remove the
combustion fan, if the gasket is torn you can
remove the gasket and use red RTV high
temperature si�icone to make a new gasket
for the fan.
• You may need to remove the pipe from the
back of your stove and use a wire brush and
vacuum to c�ean that as we��.
• �t may be necessary to hire a chimney
sweep to c�ean out your venting system
regu�ar�y. You must take specia� care with
e�bows as they can bui�d up creosote more
than straight pipes.
• �t is a�so a good idea to c�ean your in�et duct
year�y as we��. �t is �ocated behind the right
hand side pane�.
There is an air in�et cover that must be removed,
and the airway shou�d be c�eaned. �f the gasket
gets torn or damaged a new one can be made
with red RTV.
EN
16