Werbung
Verfügbare Sprachen
Verfügbare Sprachen
- Do not use electric tools in a damp or wet environ-
ment. There is a risk of electric shock!
- Make sure that the work area is well-illuminated.
- Do not use power tools where there is a risk of
fire or explosion.
3.
Protect yourself from electric shock
- Avoid physical contact with earthed parts (e. g.
pipes, radiators, electric ranges, cooling units).
4.
Keep away from children!
- Do not allow other persons to touch the tool and
cable, keep them away from your work area.
5.
Securely store unused power tools
- Unused power tools should be stored in a dry, ele-
vated or closed location out of the reach of children.
6.
Do not overload your power tool
- They work better and more safely in the specified
output range.
7.
Wear suitable clothing
- Do not wear wide clothing or jewellery, which can
become entangled in moving parts.
- Rubber gloves and anti-slip footwear are recom-
mended when working outdoors.
- Tie long hair back in a hair net.
8.
Do not use the cable for purposes for which it is
not intended
- Do not use the cable to pull the plug out of the outlet.
Protect the cable from heat, oil and sharp edges.
9.
Take care of your tools
- Keep your compressor clean in order to work well
and safely.
- Follow the maintenance instructions.
- Check the connection cable of the electric tool
regularly and have it replaced by a recognised
specialist when damaged.
- Check extension cables regularly and replace
them when damaged.
10. Pull the connector out of the socket
- When the power tool is not in use or prior to main-
tenance and when replacing tools such as saw
blades, drills, cutters.
11. Avoid inadvertent starting
- Make sure that the switch is switched off when
plugging the plug into an outlet.
12. Use extension cables for outdoors
- Only use approved and appropriately identified
extension cables for use outdoors.
- Only use cable reels in the unrolled state.
13. Always remain attentive
- Pay attention to what you are doing. Remain sen-
sible when working. Do not use the power tool
when you are distracted.
24 | GB
14. Check the power tool for potential damage
- Protective devices or other parts with minor dam-
age must be carefully inspected to ensure that they
function correctly and as intended prior to contin-
ued use of the power tool.
- Check whether the moving parts function fault-
lessly and do not jam or whether parts are dam-
aged. All parts must be correctly mounted and all
conditions must be fulfilled to ensure fault-free
operation of the power tool.
- Damaged protective devices and parts must be
properly repaired or replaced by a recognised
specialist workshop, insofar as nothing different
is specified in the operating manual.
- Damaged switches must be replaced at a cus-
tomer service workshop.
- Do not use any faulty or damaged connection
cables.
- Do not use any power tool on which the switch
cannot be switched on and off.
15. Have your power tool repaired by a qualified elec-
trician
- This power tool conforms to the applicable safety
regulations. Repairs may only be performed by an
electrician using original spare parts. Otherwise
accidents can occur.
16. Attention!
- For your own safety, only use accessories and
additional equipment that are indicated in the
operating manual or have been recommended or
indicated by the manufacturer. Use of other tools
or accessories that those recommended in the
operating manual or in the catalogue could rep-
resent a personal danger to you.
17. Noise
- Wear hearing protection when using the com-
pressor.
18. Replacing the connection line
- If the connection line is damaged, it must be re-
placed by the manufacturer or an electrician to
avoid danger. There is a risk of electric shock.
19. Inflating tyres
- Check the tyre pressure immediately after filling
using a suitable pressure gauge, e.g. at a petrol
station.
20. Street-legal compressors in construction site op-
eration
- Ensure that all hoses and fixtures are suitable for
the maximum permissible working pressure of the
compressor.
www.scheppach.com
Werbung
