Herunterladen Inhalt Inhalt
Teilen
Diese Seite drucken
  1. Anleitungen
  2. Marken
  3. Hirschmann Anleitungen
  4. Switch
  5. RM CLI HiOS-2S RSPS
  6. Referenzhandbuch

Hirschmann RM CLI HiOS-2S RSPS Referenzhandbuch

Command line interface; rail switch power smart
Vorschau ausblenden
Inhaltsverzeichnis

Werbung

Quicklinks

Diese Anleitung herunterladen
Referenz-Handbuch
Command Line Interface (CLI)
Rail Switch Power Smart (HiOS-2S RSPS)
RM CLI HiOS-2S RSPS
Technische Unterstützung
Release 3.0 01/2014
https://hirschmann-support.belden.eu.com

Werbung

Inhaltsverzeichnis
loading

Verwandte Anleitungen für Hirschmann RM CLI HiOS-2S RSPS

Inhaltszusammenfassung für Hirschmann RM CLI HiOS-2S RSPS

  • Seite 1 Referenz-Handbuch Command Line Interface (CLI) Rail Switch Power Smart (HiOS-2S RSPS) RM CLI HiOS-2S RSPS Technische Unterstützung Release 3.0 01/2014 https://hirschmann-support.belden.eu.com...
  • Seite 2 Die beschriebenen Leistungsmerkmale sind nur dann verbindlich, wenn sie bei Vertragsschluss ausdrücklich vereinbart wurden. Diese Druckschrift wurde von Hirschmann Automation and Control GmbH nach bestem Wissen erstellt. Hirschmann behält sich das Recht vor, den Inhalt dieser Druckschrift ohne Ankündigung zu ändern. Hirschmann gibt keine Garantie oder Gewähr- leistung hinsichtlich der Richtigkeit oder Genauigkeit der Angaben in dieser Druckschrift.

  • Seite 3: Inhaltsverzeichnis

    Ausführen von Kommandos C.2.1 Syntaxanalyse C.2.2 Kommandobaum C.2.3 Aufbau eines Kommandos Eigenschaften des CLI C.3.1 Eingabeprompt C.3.2 Tastaturkombinationen C.3.3 Eingabehilfen Beispiele IP-Adresse einstellen Konfiguration speichern Syntax des Kommandos „radius server auth add“ Wartung RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 4 2.1.3 appllists disable show 2.2.1 show appllists Authentication authlists 3.1.1 authlists add 3.1.2 authlists delete 3.1.3 authlists set-policy 3.1.4 authlists enable 3.1.5 authlists disable show 3.2.1 show authlists Auto Disable auto-disable 4.1.1 auto-disable reason RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 5 6.1.2 cli prompt 6.1.3 cli numlines 6.1.4 cli banner operation 6.1.5 cli banner text show 6.2.1 show cli global 6.2.2 show cli command-tree logging 6.3.1 logging cli-command show 6.4.1 show logging cli-command Clock clock RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 6 8.3.9 copy config nvm 8.3.10 copy config envm 8.3.11 copy config remote 8.3.12 copy sfp-white-list remote 8.3.13 copy sfp-white-list envm clear 8.4.1 clear config 8.4.2 clear factory 8.4.3 clear sfp-white-list show 8.5.1 show running-config xml RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 7 10.1.7 device-status trap 10.2 device-status 10.2.1 device-status link-alarm 10.3 show 10.3.1 show device-status monitor 10.3.2 show device-status state 10.3.3 show device-status trap 10.3.4 show device-status events 10.3.5 show device-status link-alarm 10.3.6 show device-status all RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 8 12.2.2 dhcp-server pool add 12.2.3 dhcp-server pool modify 12.2.4 dhcp-server pool mode 12.2.5 dhcp-server pool delete 12.3 show 12.3.1 show dhcp-server operation 12.3.2 show dhcp-server pool 12.3.3 show dhcp-server interface 12.3.4 show dhcp-server lease DoS Mitigation RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 9 14.3 show 14.3.1 show dot1x global 14.3.2 show dot1x auth-history 14.3.3 show dot1x detail 14.3.4 show dot1x summary 14.3.5 show dot1x clients 14.3.6 show dot1x statistics 14.4 clear 14.4.1 clear dot1x statistics port RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 10 15.3.6 show lacp actor 15.3.7 show lacp partner operational 15.3.8 show lacp partner admin 16.1 mac-filter 16.2 bridge 16.2.1 bridge aging-time 16.3 show 16.3.1 show mac-filter-table static 16.4 show 16.4.1 show bridge aging-time RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 11 19.2.1 copy httpscert remote 19.3 show 19.3.1 show https Integrated Authentification Server (IAS) 20.1 ias-users 20.1.1 ias-users add 20.1.2 ias-users delete 20.1.3 ias-users enable 20.1.4 ias-users disable 20.1.5 ias-users password 20.2 show 20.2.1 show ias-users RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 12 22.4.7 show igmp-snooping querier vlan all 22.4.8 show igmp-snooping querier vlan vlan-id 22.4.9 show igmp-snooping enhancements vlan 22.4.10show igmp-snooping enhancements unknown-filte- ring 22.4.11show igmp-snooping statistics global 22.4.12show igmp-snooping statistics interface 22.5 show 22.5.1 show mac-filter-table igmp-snooping RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 13 24.2 clear 24.2.1 clear port-statistics 24.3 show 24.3.1 show interface counters 24.3.2 show interface utilization 24.3.3 show interface statistics 24.3.4 show interface ether-stats Intern 25.1 help 25.2 logout 25.3 history 25.4 enable 25.5 configure RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 14 26.1.1 vlan association 26.2 show 26.2.1 show vlan association Internet Protocol Version 4 (IPv4) 27.1 network 27.1.1 network protocol 27.1.2 network parms 27.2 clear 27.2.1 clear arp-table-switch 27.3 show 27.3.1 show network parms RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 15 29.3.6 lldp tlv mac-phy-config-state 29.3.7 lldp tlv max-frame-size 29.3.8 lldp tlv mgmt-addr 29.3.9 lldp tlv port-desc 29.3.10lldp tlv port-vlan 29.3.11lldp tlv protocol 29.3.12lldp tlv sys-cap 29.3.13lldp tlv sys-desc 29.3.14lldp tlv sys-name 29.3.15lldp tlv vlan-name RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 16 31.1.13logging persistent filesize 31.1.14logging persistent severity-level 31.2 show 31.2.1 show logging buffered 31.2.2 show logging traplogs 31.2.3 show logging console 31.2.4 show logging persistent 31.2.5 show logging syslog 31.2.6 show logging host 31.3 copy RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 17 34.1.4 network management access modify 34.1.5 network management access operation 34.1.6 network management access status 34.2 show 34.2.1 show network management access global 34.2.2 show network management access rules Media Redundancy Protocol (MRP) RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 18 37.2.3 show mrp-ieee mmrp statistics global 37.2.4 show mrp-ieee mmrp statistics interface 37.2.5 show mrp-ieee mmrp service-requirement forward-all vlan 37.2.6 show mrp-ieee mmrp service-requirement forbidden vlan 37.3 mrp-ieee 37.3.1 mrp-ieee mmrp operation 37.3.2 mrp-ieee mmrp periodic-machine 37.4 clear RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 19 39.2.5 port-monitor condition link-flap count 39.2.6 port-monitor condition link-flap mode 39.2.7 port-monitor condition duplex-mismatch mode 39.2.8 port-monitor condition overload-detection traffic-type 39.2.9 port-monitor condition overload-detection threshold- type 39.2.10port-monitor condition overload-detection upper-th- reshold 39.2.11port-monitor condition overload-detection lower-th- reshold RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 20 41.1.2 ptp clock-mode 41.1.3 ptp sync-lower-bound 41.1.4 ptp sync-upper-bound 41.1.5 ptp management 41.1.6 ptp v2-transparent-clock syntonization 41.1.7 ptp v2-transparent-clock network-protocol 41.1.8 ptp v2-transparent-clock multi-domain 41.1.9 ptp v2-transparent-clock sync-local-clock 41.1.10ptp v2-transparent-clock delay-mechanism 41.1.11ptp v2-transparent-clock primary-domain RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 21 42.1.5 passwords min-numeric-chars 42.1.6 passwords min-special-chars 42.2 show 42.2.1 show passwords Radius 43.1 authorization 43.1.1 authorization network radius 43.2 radius 43.2.1 radius accounting mode 43.2.2 radius server attribute 4 43.2.3 radius server acct add RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 22 45.2.1 copy script envm 45.2.2 copy script remote 45.2.3 copy script nvm 45.2.4 copy script running-config nvm 45.2.5 copy script running-config envm 45.2.6 copy script running-config remote 45.3 show 45.3.1 show script envm RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 23 48.1.9 signal-contact trap 48.2 signal-contact 48.2.1 signal-contact link-alarm 48.3 show 48.3.1 show signal-contact Switched Monitoring (SMON) 49.1 monitor 49.1.1 monitor session 49.2 show 49.2.1 show monitor session 49.3 clear 49.3.1 clear monitor session RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 24 53.1.6 sntp client server add 53.1.7 sntp client server delete 53.1.8 sntp client server mode 53.1.9 sntp server operation 53.1.10sntp server port 53.1.11sntp server only-if-synchronized 53.1.12sntp server broadcast operation 53.1.13sntp server broadcast address RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 25 54.2.7 spanning-tree guard-tcn 54.2.8 spanning-tree cost 54.2.9 spanning-tree priority 54.3 show 54.3.1 show spanning-tree global 54.3.2 show spanning-tree mst 54.3.3 show spanning-tree port Secure Shell (SSH) 55.1 ssh 55.1.1 ssh server 55.1.2 ssh timeout RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 26 System 57.1 system 57.1.1 system name 57.1.2 system location 57.1.3 system contact 57.1.4 system pre-login-banner operation 57.1.5 system pre-login-banner text 57.2 temperature 57.2.1 temperature upper-limit 57.2.2 temperature lower-limit 57.3 show 57.3.1 show eventlog RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 27 60.1.3 users enable 60.1.4 users disable 60.1.5 users password 60.1.6 users snmpv3 authentication 60.1.7 users snmpv3 encryption 60.1.8 users access-role 60.1.9 users lock-status 60.1.10users password-policy-check 60.2 show 60.2.1 show users Virtual LAN (VLAN) 61.1 name RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 28 62.2.3 voice vlan none 62.2.4 voice vlan untagged 62.2.5 voice vlan disable 62.2.6 voice vlan auth 62.2.7 voice vlan data priority 62.3 show 62.3.1 show voice vlan global 62.3.2 show voice vlan interface RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 29: Sicherheitshinweise

    Nehmen Sie eine Maschine, die mittels Datenübertragung gesteuert wird, erst in Betrieb, wenn Sie alle Geräte zur Datenübertragung vollständig kon- figuriert haben. Das Nicht-Beachten dieser Anweisung kann zu Tod, schwerer Körperverletzung oder Materialschäden führen. RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 30 Sicherheitshinweise RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 31: Über Dieses Handbuch

    Die Netzmanagement-Software Industrial HiVision bietet Ihnen weitere Mög- lichkeiten zur komfortablen Konfiguration und Überwachung:  ActiveX-Control für SCADA-Integration  Autotopologie-Erkennung  Browser-Interface  Client/Server-Struktur  Ereignisbehandlung  Ereignislogbuch  Gleichzeitige Konfiguration mehrerer Geräte  Grafische Benutzeroberfläche mit Netz-Layout  SNMP/OPC-Gateway. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 32: Legende

    Die in diesem Handbuch verwendeten Auszeichnungen haben folgende Bedeutungen:  Aufzählung  Arbeitsschritt  Zwischenüberschrift Link Querverweis mit Verknüpfung Anmerkung: Eine Anmerkung betont eine wichtige Tatsache oder lenkt Ihre Aufmerksamkeit auf eine Abhängigkeit. ASCII-Darstellung in der grafischen Benutzeroberfläche Courier RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 33: A Einführung

    Einführung A Einführung RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 34: A.1 Command Line Interface

    Sie über Wissen zu den Grundlagen und den Einsatz von Rail Switch Power Smart Geräten. Das Referenz-Handbuch "Command Line Interface" gibt Ihnen Schritt für Schritt Informationen zum Verwenden des Command Line Interface (CLI) und dessen Befehlen. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 35: B Zugang Zum Cli

    Zugang zum CLI B Zugang zum CLI RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 36: B.1 Datenverbindung Vorbereiten

    Informationen zum Konfigurieren Ihres HiOS-2S RSPS-Gerätes finden Sie im Anwender-Handbuch „Konfiguration“. Einen Zugang zur Benutzeroberfläche des Command Line Interface erhalten Sie mit Hilfe des Freeware-Programms PuTTY. Dieses Programm finden Sie auf der Produkt-CD.  Installieren Sie PuTTY auf Ihrem Rechner. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 37: Cli Über Ssh (Secure Shell)

     Im Eingabefeld Host Name (or IP address) tragen Sie die IP-Ad- resse Ihres Gerätes ein. Die IP-Adresse (a.b.c.d) besteht aus 4 Dezimalzahlen im Wert von 0 bis 255. Die 4 Dezimalzahlen sind durch einen Punkt getrennt. RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 38 Sicherheitsabfrage für den Fingerabdruck  Überprüfen Sie den Fingerabdruck. Das hilft Ihnen dabei, sich vor unlieb- samen Gästen zu schützen.  Stimmt der Fingerabdruck mit dem des Geräteschlüssels überein, dann klicken Sie „Ja“. RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 39  Geben Sie das Passwort ein. Im Lieferzustand ist das Passwort private. Drücken Sie die Eingabetaste. Das Gerät bietet Ihnen die Möglichkeit, den Benutzernamen und das Passwort später im Command Line Interface zu ändern. Beachten Sie die Schreibweise in Groß-/Kleinbuchstaben. RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 40 B.2 CLI über SSH (Secure Shell) Das Gerät zeigt den Start-Bildschirm des CLI an. Anmerkung: Ändern Sie das Passwort gleich bei der 1. Inbetriebnahme. Copyright (c) 2011-2014 Hirschmann Automation and Control GmbH All rights reserved RSPS Release HiOS-2S-3.0 (Build date 2014-02-20 20:20)

  • Seite 41: B.3 Cli Über Den V.24-Port

    Pinbelegung der V.24-Schnittstelle und des DB9-Steckers Einstellungen VT 100 Terminal Speed 9.600 Baud Data 8 bit Stopbit 1 bit Handshake Parity none Stellen Sie die seriellen Konfigurationsparameter des Terminal-Emulations- programmes wie folgt ein: RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 42 VT100 und drücken Sie eine Taste.  Alternativ erstellen Sie die serielle Datenverbindung zum Gerät über V.24 mit PuTTY (siehe Abbildung 7). Drücken Sie die Eingabetaste. Abb. 7: Serielle Datenverbindung über V.24 mit PuTTY RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 43 Zugang zum CLI B.3 CLI über den V.24-Port Nach erfolgreichem Aufbau der Datenverbindung zeigt das Gerät ein Fenster für die Eingabe des Benutzernamens an. Copyright (c) 2011-2014 Hirschmann Automation and Control GmbH All rights reserved RSPS Release HiOS-2S-3.0 (Build date 2014-02-20 20:20)
  • Seite 44 Abb. 9: CLI-Bildschirm nach dem Einloggen Anmerkung: Sie haben die Möglichkeit, die V.24-Schnittstelle als Terminal- /CLI-Schnittstelle zu konfigurieren. Drücken Sie mehrfach eine beliebige Taste Ihrer Terminal-Tastatur, bis Ihnen der Login-Bildschirm den CLI-Modus signalisiert. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 45: B.4 Cli-Zugang Über Telnet

     Schreiben Sie in das Feld „Öffnen:“ den Befehl telnet <IP-Adresse des Gerätes> Abb. 10: Telnet-Verbindung zum HiOS-2S RSPS über Windows-Eingabefenster herstellen  Eingabeaufforderung  Starten Sie mit Start>Programme>Zubehör>Eingabeaufforderung den DOS-Kommandozeileninterpreter auf Ihrem Rechner. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 46: B.4.2 Telnet-Verbindung Über Putty

    <IP-Adresse des Gerätes> Abb. 11: Telnet-Verbindung zum HiOS-2S RSPS über DOS-Kommandozeile her- stellen B.4.2 Telnet-Verbindung über PuTTY  Starten Sie das Programm PuTTY auf Ihrem Rechner. PuTTY meldet sich mit dem Anmeldebildschirm. RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 47 255. Die 4 Dezimalzahlen sind durch einen Punkt getrennt.  Um den Verbindungstyp auszuwählen, klicken Sie unter Connection type den Punkt Telnet an.  Klicken Sie auf „Open“, um die Datenverbindung zu Ihrem Gerät aufzu- bauen. RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 48 Drücken Sie die Eingabetaste. Das Gerät bietet Ihnen die Möglichkeit, den Benutzernamen und das Passwort später im Command Line Interface zu ändern. Beachten Sie die Schreibweise in Groß-/Kleinbuchstaben. Das Gerät zeigt den Start-Bildschirm des CLI an. RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 49 Zugang zum CLI B.4 CLI-Zugang über Telnet Copyright (c) 2011-2014 Hirschmann Automation and Control GmbH All rights reserved RSPS Release HiOS-2S-3.0 (Build date 2014-02-20 20:20) System Name RSPS-ECE555F5D460 Management IP : 10.115.45.105 Subnet Mask 255.255.224.0 Base MAC EC:E5:55:F5:D4:60 System Time...
  • Seite 50 Zugang zum CLI B.4 CLI-Zugang über Telnet RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 51: C Bedienung Des Cli

    Bedienung des CLI C Bedienung des CLI RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 52: Modus-Basierte Kommando-Hierarchie

    Eine Ausnahme bilden die User-Exec-Modus Kommandos. Das CLI bietet Ihnen die Möglichkeit, diese Kommandos sowohl im User-Exec-Modus als auch im Privileged-Exec-Modus auszuführen. Die folgende Abbildung zeigt die Modi des Command Line Interface. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 53: Bedienung Des Cli

    Das CLI unterstützt, abhängig von der Berechtigungsstufe (User Level), die folgenden Modi:  User-Exec-Modus Nach der Anmeldung im CLI befinden Sie sich im User Exec Modus. Der User Exec Modus enthält einen begrenzten Umfang an Kommandos. Kommando-Prompt: (RSPS) > RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 54 (RSPS) (interface 2/1)#  Eine Portreihe an einem Interface Kommando-Prompt: (RSPS) (interface <interface range> )# Beispiel: Beim Wechsel vom Global-Config-Modus in den Interface- Range-Modus ändert sich das Kommando-Prompt wie folgt: (RSPS) (config)#interface 1/2-1/4 (RSPS) ((Interface)1/2-1/4)# RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 55 Um den VLAN-Modus zu beenden ben Sie den Befehl vlan und in den Privileged-Exec-Modus database ein. zurückzukehren, geben Sie exit ein oder drücken Sie Ctrl-Z. (RSPS) #vlan database (RSPS) (Vlan)# (RSPS) (Vlan)#exit (RSPS) # Tab. 1: Kommando-Modi RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 56 Modus zurückzukehren, geben Sie exit ein. Um zum Privileged-Exec- {all|<slot/port>|<interfa- Modus zurückzukehren, drücken Sie ce range> |<interface Ctrl-Z. list>|<complex range>}ein. (RSPS) (config)#interface (RSPS) (interface <slot/port> slot/port)#exit (RSPS) (interface (RSPS) # slot/port)# Tab. 1: Kommando-Modi RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 57 Exit this session. ping Send ICMP echo packets to a specified IP address. show Display device options and settings. telnet Establish a telnet connection to a remote host. (RSPS)> Abb. 15: Kommandos im User-Exec-Modus RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 58: C.2 Ausführen Von Kommandos

    Kommando komplett definiert und damit ausführbar ist. Das CLI prüft die Eingaben. Wenn ein Befehl und die Parameter korrekt und vollstän- dig sind, ist der Befehl durch Betätigen der Eingabetaste ausführbar. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 59: C.2.3 Aufbau Eines Kommandos

    Dieses Handbuch stellt die Befehle und Parameter in der Schriftart Cou- rier dar. Verwenden Sie Befehle und Parameter wie im Handbuch ab- gebildet (siehe Tabelle Parameter  Die Reihenfolge der Parameter ist für die korrekte Syntax eines Kom- mandos relevant. RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 60 Benutzerdefinierter Text mit einer Länge im angegebenen Bereich, z.B. maximal 32 Zeichen. character string Verwenden Sie zwei Anführungszeichen, um Zeichenketten zu kennzeichnen, zum Beispiel “System Name mit Leerzeichen”. Tab. 3: Parameterwerte im Command Line Interface RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 61 „Systemname mit Leerzeichen”. Leerzeichen sind keine gültigen benut- zerdefinierten Strings. Ein Leerzeichen in einem Parameter geben Sie in- nerhalb von Anführungszeichen ein. Beispiel: *(RSPS)#cli prompt Device name Error: Invalid command 'name' *(RSPS)#cli prompt 'Device name' *(Device name)# RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 62: Beispiele Für Kommandos

    „radius server auth modify“ ist die Befehlsbezeichnung. Der Parameter <1..8> (RADIUS server index) ist notwendig. Der Werte- bereich des Parameters liegt bei 1 bis 8 (ganze Zahl). Die Parameter [name], [port], [msgauth], [primary], [status], [secret] und [encrypted] sind optional. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 63: C.3 Eigenschaften Des Cli

     (RSPS) ((Interface)1/2-1/4)# Interface-Range-Modus / Eine Portreihe an einem Interface  (RSPS) ((Interface)1/2,1/4,1/5)# Interface-Range-Modus / Eine Auflistung von einzelnen Ports  (RSPS) ((Interface)1/1-1/2,1/4-1/6)# Interface-Range-Modus / Eine Auflistung von Portreihen und einzel- nen Ports RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 64: Stern, Rautezeichen Und Ausrufezeichen

    Das Gerätbietet Ihnen die Möglichkeit, das Eingabeprompt zu ändern. Das CLI unterstützt die folgenden Wildcards: Wildcard Description Systemdatum. Systemzeit. IP-Adresse des Gerätes. MAC-Adresse des Gerätes. Produktname des Gerätes. Tab. 5: Verwendung von Wildcards im CLI-Eingabeprompt RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 65: C.3.2 Tastaturkombinationen

    Zeile erneut schreiben oder Inhalte einfügen CTRL + N Zur nächsten Zeile im Speicher wechseln CTRL + Z Zum Ursprung wechseln CTRL + G Laufende tcpdump-Ausgabe abbrechen Tab. 6: Tastenkombinationen im Command Line Interface RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 66 ..return to root command prompt Ctrl-G ..aborts running tcpdump session Tab, <SPACE> command-line completion Exit ..go to next lower command prompt ..list choices (RSPS) # Abb. 16: Auflisten der Tastenkombinationen mit dem Help-Kommando RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 67: C.3.3 Eingabehilfen

    CLI den Befehl bis zum Beginn der Mehrdeutigkeit zu „log“. (RSPS) (Config)#log Nach dem erneuten Betätigen der Taste "Tab" oder "Leerzeichen" gibt Ihnen das CLI die Auswahlliste (logging, logout) aus. (RSPS) (Config)#log logging logout RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 68: Mögliche Befehle/Parameter

    Durch Eingabe des dargestellten Befehls erhalten Sie eine Liste der ver- fügbaren Parameter zum Befehl show. Durch die Eingabe des Befehls ohne Leerzeichen vor dem Fragezeichen zeigt das Gerät den Hilfetext zum Befehl selbst: !*#(RSPS)(Config)#show? show Display device options and settings. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 69: D Beispiele

    Beispiele D Beispiele RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 70: D.1 Ip-Adresse Einstellen

    Sie sich nun im Privileged-Exec-Modus befinden. (RSPS) >enable (RSPS) #?  Geben Sie ein Fragezeichen ? ein, um sich die in diesem Modus ver- fügbaren Kommandos auflisten zu lassen. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 71: Befehl Finden, Vervollständigen Und Ausführen

    Leerzeichen ein. Das CLI ergänzt den Befehl automatisch zu net- work parms.  Geben Sie nach dem network parms ein Fragezeichen ein, um die weitere Verzweigung des Kommandos anzeigen zu lassen. (RSPS) #network parms ? <a.b.c.d> IP address. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 72: Nach Dem Network Parms Geben Sie Die Gewünschte Ip-Adresse

    (RSPS) #show network parms ? <cr> Press Enter to execute the command.  Geben Sie danach network und parms ein, um Ihre aktuellen Net- zeinstellungen auflisten zu lassen. Führen Sie den Befehl aus durch Betätigen der Eingabetaste. RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 73 Beispiele D.1 IP-Adresse einstellen *(RSPS)#show network parms IPv4 Network ------------ Local IP address......10.115.10.100 Subnetmask........255.255.255.0 Gateway address......10.0.1.1 Burned in MAC address.......ec:e5:55:01:55:60 Protocol........none Management VLAN ID......1 Management VLAN priority....0 Management IP-DSCP value....0 *(RSPS)# RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 74: D.2 Konfiguration Speichern

     Führen Sie den Befehl aus durch Betätigen der Eingabetaste. (RSPS)>enable !*(RSPS)#s? save Save configuration. script CLI Script File. serviceshell Enter system mode. show Display device options and settings. !*(RSPS)#save? [profile] Save configuration to profile. <cr> Press Enter to execute the command. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 75: Syntax Des Kommandos „Radius Server Auth Add

    2 ip 10.115.40.50 name radius- server2  radius server auth add 3 ip 10.115.50.60 port 1813  radius server auth add 4 ip 10.115.60.70 name radius- server4 port 1814 RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 76 Beispiele D.3 Syntax des Kommandos „radius server auth add“ RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 77: E Wartung

    Wartung E Wartung Hirschmann arbeitet ständig an der Verbesserung und Weiterentwicklung der Software. Prüfen Sie regelmäßig, ob ein neuerer Stand der Software Ih- nen weitere Vorteile bietet. Informationen und Downloads von Software fin- den Sie auf den Produktseiten der Hirschmann-Website.

  • Seite 78: E.1 Service-Shell

     Um die Service-Shell-Funktion zu starten, geben Sie im Privileged-Exec- Modus serviceshell oder ser und ein Leerzeichen ein und drücken die Eingabetaste.  Um die Service-Shell-Funktion zu beenden, geben Sie exit ein und drücken die Eingabetaste. RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 79 Reset the device (cold start). save Save configuration. serviceshell Enter system mode. Set device parameters. show Display device options and settings. traceroute Trace route to a specified host. !(RSPS) #serviceshell -> exit Au revoir! !*(RSPS) # RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 80: Service-Shell Permanent Deaktivieren

    Leerzeichen ein und drü- cken die Eingabetaste. Der Vorgang ist irreversibel. !(RSPS) >enable !(RSPS) #serviceshell? [deactivate] Disable the service shell access permanently (Cannot be undone). <cr> Press Enter to execute the command. !(RSPS) #serviceshell deactivate RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 81: Kommandoreferenz

    Kommandoreferenz Kommandoreferenz RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 82: Acd Detection Mode

    'active' is sending once ARP or NDP probes into the network. passive-only Configure passive detection. The device lis- tens passively on the network if another de- vice with an already locally configured ip address appears. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 83: Address-Conflict Detection-Ongoing

    Maximum number of frequent address protections.  Mode: Global Config Mode  Privilege Level: Operator  Format: address-conflict max-protection <P-1> Parameter Value Meaning 0..100 Maximun number of frequent address protec- tions (default 3). RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 84: Address-Conflict Protect-Interval

    Privilege Level: Guest  Format: show address-conflict global 1.2.2 show address-conflict detected Displays the last detected address conflict.  Mode: command is in all modes available  Privilege Level: Guest  Format: show address-conflict detected RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 85: Show Address-Conflict Fault-State

    ACD Detection Mode 1.2 show 1.2.3 show address-conflict fault-state Displays the current conflict status.  Mode: command is in all modes available  Privilege Level: Guest  Format: show address-conflict fault-state RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 86: Application

    Deactivate a login application list.  Mode: Global Config Mode  Privilege Level: Administrator  Format: appllists disable <P-1> Parameter Value Meaning string <application> Name of an application list. show Display device options and settings. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 87: Show Appllists

    Application 2.2 show 2.2.1 show appllists Display ordered methods for application lists.  Mode: command is in all modes available  Privilege Level: Administrator  Format: show appllists RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 88: Authentication

    [<P-5>] [<P-6>] Parameter Value Meaning string <authlist_name> Name of an authentication list. reject Authentication is rejected / not allowed local Authentication by local user DB radius Authentication by RADIUS server Authentication by IAS server RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 89: Authlists Enable

    Deactivate a login authentication list.  Mode: Global Config Mode  Privilege Level: Administrator  Format: authlists disable <P-1> Parameter Value Meaning string <authlist_name> Name of an authentication list. show Display device options and settings. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 90: Show Authlists

    Authentication 3.2 show 3.2.1 show authlists Display ordered methods for authentication lists.  Mode: command is in all modes available  Privilege Level: Administrator  Format: show authlists RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 91: Auto Disable

    Timer value in seconds after a deactivated port is activated again. Possible values are: 30-4294967295. A value of 0 disables the timer.  Mode: Interface Range Mode  Privilege Level: Operator  Format: auto-disable timer <P-1> RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 92: Auto-Disable Reset

     Format: show auto-disable brief 4.3.2 show auto-disable reasons Display summary of Auto Disable error reasons  Mode: command is in all modes available  Privilege Level: Guest  Format: show auto-disable reasons RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 93: Class Of Service

    Class Of Service 5.1 classofservice Class Of Service classofservice Class of service configuration. 5.1.1 classofservice ip-dscp-mapping ip-dscp-mapping configuration  Mode: Global Config Mode  Privilege Level: Operator  Format: classofservice ip-dscp-mapping <P-1> <P-2> <P-3> RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 94 Class Of Service 5.1 classofservice RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 95 Class Of Service 5.1 classofservice Parameter Value Meaning af11 af12 af13 af21 af22 af23 af31 af32 af33 af41 af42 af43 RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 96: Classofservice Dot1P-Mapping

    Sets the class of service trust mode to un- trusted dot1p Sets the class of service trust mode to dot1p. ip-dscp Sets the class of service trust mode to IP DSCP. cos-queue COS queue configuration RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 97: Cos-Queue Strict

    Enter a number in the given range. show Display device options and settings. 5.4.1 show classofservice ip-dscp-mapping Show ip-dscp-mapping configuration.  Mode: command is in all modes available  Privilege Level: Guest  Format: show classofservice ip-dscp-mapping RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 98: Show Classofservice Dot1P-Mapping

    Mode: command is in all modes available  Privilege Level: Guest  Format: show classofservice trust 5.4.4 show cos-queue Show cosqueue parameters  Mode: command is in all modes available  Privilege Level: Guest  Format: show cos-queue RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 99: Cli

    Set the number of lines for 'more'.  Mode: command is in all modes available  Privilege Level: Guest  Format: cli numlines <P-1> Parameter Value Meaning 0..250 Screen size for 'more' (23 = default, 0 = un- limited). RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 100: Cli Banner Operation

    Privilege Level: Guest  Format: show cli global 6.2.2 show cli command-tree Show a list of all commands.  Mode: command is in all modes available  Privilege Level: Guest  Format: show cli command-tree RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 101: Logging

    Display device options and settings. 6.4.1 show logging cli-command Show the CLI command logging preferences.  Mode: command is in all modes available  Privilege Level: Guest  Format: show logging cli-command RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 102: Clock

    Meaning string Edit the timezone acronym (max 4 charac- ters). 7.1.4 clock summer-time mode Configure summer-time mode parameters.  Mode: Global Config Mode  Privilege Level: Administrator  Format: clock summer-time mode <P-1> RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 103: Clock Summer-Time Recurring Start

    Sunday Monday Tuesday Wednesday Thursday Friday Saturday none January February March April June July August September October November December string <hh:mm> Present time in hh:mm format (00:00- 23:59). RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 104: Clock Summer-Time Recurring End

    <hh:mm> Present time in hh:mm format (00:00- 23:59). 7.1.7 clock summer-time zone Edit timezone acronym for summer-time (max. 4 characters).  Mode: Global Config Mode  Privilege Level: Administrator  Format: clock summer-time zone <P-1> RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 105: Show

    Display device options and settings. 7.2.1 show clock Display the current time information.  Mode: command is in all modes available  Privilege Level: Guest  Format: show clock [summer-time] [summer-time]: Display summer-time parameters. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 106: Configure

    Privilege Level: Operator  Format: no config watchdog admin-state 8.2.2 config watchdog timeout Configure the Configuration Undo timeout (unit: seconds).  Mode: Global Config Mode  Privilege Level: Operator  Format: config watchdog timeout <P-1> RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 107: Config Encryption Password Set

    Format: no config envm auto-update 8.2.6 config envm config-save Allow the configuration to be saved to this memory device.  Mode: Global Config Mode  Privilege Level: Operator  Format: config envm config-save <P-1> RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 108: Config Envm Load-Priority

    Format: config profile delete <P-1> num <P-2> profile <P- 3> num: Select the index of the profile to delete. profile: Select the name of the profile to delete. Parameter Value Meaning non-volative memory envm external non-volative memory device RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 109: Config Fingerprint Verify

    Privilege Level: Operator  Format: copy sysinfo system envm [filename <P-1>] [filename]: Enter filename (filename xyz.html) on external non-volative memory device. Parameter Value Meaning string Enter a user-defined text, max. 32 charac- ters. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 110: Copy Sysinfoall System Envm

    Enter a user-defined text, max. 32 charac- ters. 8.3.6 copy firmware system remote Copy firmware to file server.  Mode: Privileged Exec Mode  Privilege Level: Operator  Format: copy firmware system remote <P-1> RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 111: Copy Config Running-Config Nvm

    <P-2> [profile]: Load configuration from profile. running-config: (Re)-load configuration from NV memory. remote: Copy configuration from nvm to server. Parameter Value Meaning string Filename. string Enter a user-defined text, max. 128 charac- ters. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 112: Copy Config Envm

    Enter a user-defined text, max. 128 charac- ters. 8.3.13 copy sfp-white-list envm Copy SFP WhiteList from external non-volative memory device.  Mode: Privileged Exec Mode  Privilege Level: Operator  Format: copy sfp-white-list envm <P-1> nvm RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 113: Clear

     Privilege Level: Administrator  Format: clear factory 8.4.3 clear sfp-white-list Clear SFP WhiteList  Mode: Privileged Exec Mode  Privilege Level: Operator  Format: clear sfp-white-list show Display device options and settings. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 114: Show Running-Config Xml

     Format: show config envm properties 8.6.3 show config watchdog Show the Auto Configuration Undo settings.  Mode: command is in all modes available  Privilege Level: Guest  Format: show config watchdog RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 115: Show Config Encryption

    Index of the profile entry. 8.6.6 show config status Show sync Status of running-config with NVM and ACA.  Mode: command is in all modes available  Privilege Level: Guest  Format: show config status RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 116: Debug

    Privilege Level: Operator  Format: debug tcpdump stop 9.1.4 debug tcpdump filter show Display a known filter file.  Mode: Privileged Exec Mode  Privilege Level: Operator  Format: debug tcpdump filter show <P-1> RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 117: Debug Tcpdump Filter List

    Copy internal capture file from device to the server.  Mode: Privileged Exec Mode  Privilege Level: Operator  Format: copy tcpdumpcap nvm remote <P-1> Parameter Value Meaning string Enter a user-defined text, max. 128 charac- ters. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 118: Copy Tcpdumpfilter Remote

    Copy capture filter from non-volatile memory to external non-volatile memory. remote: Copy capture file from non-volatile memory to the server. Parameter Value Meaning string Filename. string <filename> Enter a valid filename. string Enter a user-defined text, max. 128 charac- ters. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 119: 10 Device Monitor

    Format: no device-status monitor temperature 10.1.3 device-status monitor envm-removal Enable or disable monitoring the presence of the external non-volative me- mory.  Mode: Global Config Mode  Privilege Level: Administrator  Format: device-status monitor envm-removal RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 120: Device-Status Monitor Envm-Not-In-Sync

    Enable or disable monitoring the condition of the power supply(s).  Mode: Global Config Mode  Privilege Level: Administrator  Format: device-status monitor power-supply <P-1> Parameter Value Meaning 1..2 Number of power supply. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 121: Device-Status Trap

    Privilege Level: Administrator  Format: device-status link-alarm no device-status link-alarm  Disable the option  Mode: Interface Range Mode  Privilege Level: Administrator  Format: no device-status link-alarm 10.3 show Display device options and settings. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 122: Show Device-Status Monitor

    Privilege Level: Guest  Format: show device-status link-alarm 10.3.6 show device-status all Display the configurable device status settings.  Mode: command is in all modes available  Privilege Level: Guest  Format: show device-status all RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 123: 11 Device Security

    The device changes the security status to the value "error" if the value for at least one of the following password rules is 0:\n"minimum upper cases","mi- nimum lower cases","minimum numbers","minimum special characters".  Mode: Global Config Mode  Privilege Level: Administrator  Format: security-status monitor pwd-policy-config RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 124: Security-Status Monitor Pwd-Policy-Inactive

    Format: no security-status monitor telnet-enabled 11.1.6 security-status monitor http-enabled Sets the monitoring of the activation of http on the switch.  Mode: Global Config Mode  Privilege Level: Administrator  Format: security-status monitor http-enabled RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 125: Security-Status Monitor Snmp-Unsecure

    Format: no security-status monitor sysmon-enabled 11.1.9 security-status monitor extnvm-upd-enabled Sets the monitoring of activation of the configuration\n saving to external non volatile memory.  Mode: Global Config Mode  Privilege Level: Administrator  Format: security-status monitor extnvm-upd-enabled RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 126: 10Security-Status Monitor No-Link-Enabled

    Format: no security-status monitor hidisc-write-enab- 11.1.12 security-status monitor extnvm-load-unsecure Sets the monitoring of security of the configuration loading from extnvm.  Mode: Global Config Mode  Privilege Level: Administrator  Format: security-status monitor extnvm-load-unsecure RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 127: 13Security-Status Monitor Iec61850-Mms-Enabled

     Format: security-status trap no security-status trap  Disable the option  Mode: Global Config Mode  Privilege Level: Administrator  Format: no security-status trap 11.2 security-status Configure the security status interface settings. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 128: Security-Status No-Link

    Format: show security-status state 11.3.3 show security-status no-link Display the settings of the monitoring of the specific\nnetwork ports.  Mode: command is in all modes available  Privilege Level: Guest  Format: show security-status no-link RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 129: Show Security-Status Trap

    Privilege Level: Guest  Format: show security-status events 11.3.6 show security-status all Display all security status settings.  Mode: command is in all modes available  Privilege Level: Guest  Format: show security-status all RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 130: Dynamic Host Configuration Protocol (Dhcp)

    Mode: Global Config Mode  Privilege Level: Operator  Format: dhcp-server operation no dhcp-server operation  Disable the option  Mode: Global Config Mode  Privilege Level: Operator  Format: no dhcp-server operation RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 131: Dhcp-Server Pool Add

    Enter the leasetime in seconds. option: Configuration option. configpath: Configpath in 'tftp://<servername>/<file>' format. gateway: Default gateway. netmask: Option netmask. wins: Option wins. dns: Option dns. hostname: Option hostname. Parameter Value Meaning 1..128 Pool ID. slot no./port no. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 132: Dhcp-Server Pool Mode

    Format: dhcp-server pool mode <P-1> Parameter Value Meaning 1..128 Pool ID. no dhcp-server pool mode  Disable the option  Mode: Global Config Mode  Privilege Level: Operator  Format: no dhcp-server pool mode RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 133: Dhcp-Server Pool Delete

    12.3.3 show dhcp-server interface Show DHCP Server per interface.  Mode: command is in all modes available  Privilege Level: Guest  Format: show dhcp-server interface [<P-1>] Parameter Value Meaning slot no./port no. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 134: Show Dhcp-Server Lease

    Dynamic Host Configuration Protocol 12.3 show (DHCP) 12.3.4 show dhcp-server lease Show DHCP Server lease entries.  Mode: command is in all modes available  Privilege Level: Guest  Format: show dhcp-server lease RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 135: 13 Dos Mitigation

    Format: no dos tcp-xmas 13.1.3 dos tcp-syn-fin Enables TCP SYN/FIN scan protection - TCP with SYN and FIN flags set.  Mode: Global Config Mode  Privilege Level: Operator  Format: dos tcp-syn-fin RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 136: Dos Tcp-Min-Header

    Mode: Global Config Mode  Privilege Level: Operator  Format: dos icmp payload-check no dos icmp payload-check  Disable the option  Mode: Global Config Mode  Privilege Level: Operator  Format: no dos icmp payload-check RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 137: Dos Icmp Payload-Size

    Privilege Level: Operator  Format: no dos tcp-offset 13.1.10 dos tcp-syn Enables TCP SYN and L4 source port smaller than 1024 protection.  Mode: Global Config Mode  Privilege Level: Operator  Format: dos tcp-syn RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 138: 11Dos L4-Port

    Format: no dos icmp-smurf-attack 13.2 show Display device options and settings. 13.2.1 show dos Show DoS Mitigation parameters  Mode: command is in all modes available  Privilege Level: Guest  Format: show dos RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 139: 14 Dot1X

    Mode: Global Config Mode  Privilege Level: Operator  Format: no dot1x system-auth-control 14.1.3 dot1x monitor Enable or disable 802.1X monitor mode.  Mode: Global Config Mode  Privilege Level: Operator  Format: dot1x monitor RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 140: Dot1X

    Mode: Interface Range Mode  Privilege Level: Operator  Format: dot1x port-control <P-1> Parameter Value Meaning auto Port is actually controlled by protocol. force-authorized Port is authorized unconditionally (de- fault). force-unauthorized Port is unauthorized unconditionally. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 141: Dot1X Re-Authentication

    Guest-vlan timeout in seconds (default: 90). 14.2.7 dot1x timeout reauth-period Configure the re-authentication period.  Mode: Interface Range Mode  Privilege Level: Operator  Format: dot1x timeout reauth-period <P-1> Parameter Value Meaning 1..65535 Timeout in seconds. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 142: Dot1X Timeout Quiet-Period

    1..65535 Timeout in seconds. 14.2.12 dot1x initialize Begins the initialization sequence on the specified port (port-control mode must be 'auto').  Mode: Interface Range Mode  Privilege Level: Operator  Format: dot1x initialize RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 143: 13Dot1X Re-Authenticate

    Format: show dot1x global 14.3.2 show dot1x auth-history Display 802.1X authentication events and information.  Mode: command is in all modes available  Privilege Level: Guest  Format: show dot1x auth-history [<P-1>] [<P-2>] RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 144: Show Dot1X Detail

    Display the 802.1X statistics for the specified port.  Mode: command is in all modes available  Privilege Level: Guest  Format: show dot1x statistics <P-1> Parameter Value Meaning slot no./port no. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 145: Clear

    Parameter Value Meaning slot no./port no. 14.4.4 clear dot1x auth-history all Clears the 802.1X authentication history for all ports.  Mode: Privileged Exec Mode  Privilege Level: Operator  Format: clear dot1x auth-history all RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 146: 15 Dot3Ad

    Enable or disable static capability for the specified Link Aggregation Group on a device. When enabled, LACP automatically helps prevent loops and allows non-link aggregation partners to support LACP. min-links: Set the minimum links for the specified Link Aggregation Group. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 147: Link-Aggregation Delete

    Mode: Interface Range Mode  Privilege Level: Operator  Format: lacp lacpmode no lacp lacpmode  Disable the option  Mode: Interface Range Mode  Privilege Level: Operator  Format: no lacp lacpmode RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 148: Lacp Actor Admin Key

    Format: no lacp actor admin state lacp-timeout 15.2.5 lacp actor admin state aggregation Enable/disable the aggregation on the actor admin state.  Mode: Interface Range Mode  Privilege Level: Operator  Format: lacp actor admin state aggregation RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 149: Lacp Actor Admin Port Priority

    Format: no lacp partner admin state lacp-activity 15.2.9 lacp partner admin state lacp-timeout Enable/disable the LACP timeout on the partener admin state.  Mode: Interface Range Mode  Privilege Level: Operator  Format: lacp partner admin state lacp-timeout RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 150: 10Lacp Partner Admin State Aggregation

    15.2.13 lacp partner admin system-priority Configure the partener system priority.  Mode: Interface Range Mode  Privilege Level: Operator  Format: lacp partner admin system-priority <P-1> Parameter Value Meaning 0..65535 Enter a number between 0 and 65535 RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 151: 14Lacp Partner Admin System-Id

    Show the member ports for specified LAG.  Mode: command is in all modes available  Privilege Level: Guest  Format: show link-aggregation members <P-1> Parameter Value Meaning slot no./port no. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 152: Show Lacp Interface

    Show administrative partner attributes.  Mode: command is in all modes available  Privilege Level: Guest  Format: show lacp partner admin [<P-1>] Parameter Value Meaning slot no./port no. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 153: 16 Fdb

    Display device options and settings. 16.3.1 show mac-filter-table static Displays the MAC address filter table.  Mode: command is in all modes available  Privilege Level: Guest  Format: show mac-filter-table static RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 154: Show

    Enter a MAC address. 1..4042 Enter a VLAN ID. 16.6 clear Clear several items. 16.6.1 clear mac-addr-table Clears the MAC address table.  Mode: Privileged Exec Mode  Privilege Level: Operator  Format: clear mac-addr-table RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 155: 17 Hidiscovery

    Enable/disable the HiDiscovery blinking sequence on this device. This pre- fernce is not saved in configuration  Mode: Privileged Exec Mode  Privilege Level: Operator  Format: network hidiscovery blinking RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 156: Show

    Format: no network hidiscovery blinking 17.2 show Display device options and settings. 17.2.1 show network hidiscovery Show the HiDiscovery settings.  Mode: command is in all modes available  Privilege Level: Guest  Format: show network hidiscovery RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 157: Hypertext Transfer Protocol (Http)

    Format: no http server 18.2 show Display device options and settings. 18.2.1 show http Show HTTP server information.  Mode: command is in all modes available  Privilege Level: Guest  Format: show http RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 158: Http Secure (Https)

    443). 19.1.3 https certificate Generate/Delete HTTPS X509/PEM certificate.  Mode: Global Config Mode  Privilege Level: Administrator  Format: https certificate <P-1> Parameter Value Meaning generate Generates the item delete Deletes the item RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 159: Copy

    Enter a user-defined text, max. 128 charac- ters. 19.3 show Display device options and settings. 19.3.1 show https Show HTTPS server information.  Mode: command is in all modes available  Privilege Level: Guest  Format: show https RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 160: Integrated Authentification Server (Ias)

    <user> User name (up to 32 characters). 20.1.4 ias-users disable Disable IAS user.  Mode: Global Config Mode  Privilege Level: Administrator  Format: ias-users disable <P-1> Parameter Value Meaning string <user> User name (up to 32 characters). RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 161: Ias-Users Password

    20.2 show Display device options and settings. 20.2.1 show ias-users Display IAS users and user accounts information.  Mode: command is in all modes available  Privilege Level: Administrator  Format: show ias-users RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 162: 21 Iec 61850

    Mode: Global Config Mode  Privilege Level: Administrator  Format: iec61850-mms write-access no iec61850-mms write-access  Disable the option  Mode: Global Config Mode  Privilege Level: Administrator  Format: no iec61850-mms write-access RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 163: Iec61850-Mms Port

    (default: 5). 21.2 show Display device options and settings. 21.2.1 show iec61850-mms Show the IEC61850 MMS Server settings.  Mode: command is in all modes available  Privilege Level: Guest  Format: show iec61850-mms RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 164: 22 Igmp Snooping

    Sets the IGMP querier query interval time (1-1800) in seconds.  Mode: Global Config Mode  Privilege Level: Operator  Format: igmp-snooping querier query-interval <P-1> Parameter Value Meaning 1..1800 Enter a number in the given range. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 165: Igmp-Snooping Querier Timer-Expiry

    Parameter Value Meaning discard Unknown multicast frames will be discarded. flood Unknown multicast frames will be flooded. query-ports Unknown multicast frames will be forwarded only to query ports. 22.2 igmp-snooping Configure IGMP snooping. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 166: Igmp-Snooping Vlan-Id

    IP address query-and-registe- Addition of query ports to multicast filter red-ports portmasks. registered-ports-only No addition of query ports to multicast fil- ter portmasks. slot no./port no. slot no./port no. slot no./port no. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 167: Igmp-Snooping

     Format: no igmp-snooping fast-leave 22.3.3 igmp-snooping groupmembership-interval Set IGMP group membership interval time (2-3600) in seconds per interface.  Mode: Interface Range Mode  Privilege Level: Operator  Format: igmp-snooping groupmembership-interval <P-1> RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 168: Igmp-Snooping Maxresponse

    Privilege Level: Operator  Format: igmp-snooping static-query-port no igmp-snooping static-query-port  Disable the option  Mode: Interface Range Mode  Privilege Level: Operator  Format: no igmp-snooping static-query-port 22.4 show Display device options and settings. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 169: Show Igmp-Snooping Global

    Show IGMP snooping VLAN information.  Mode: command is in all modes available  Privilege Level: Guest  Format: show igmp-snooping vlan vlan-id <P-1> [<P-2>] Parameter Value Meaning 1..4042 Enter the VLAN ID. detail Show detail RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 170: Show Igmp-Snooping Querier Global

    Enter the VLAN ID. 22.4.10 show igmp-snooping enhancements unknown-filte- ring Show unknown multicast filering information.  Mode: command is in all modes available  Privilege Level: Guest  Format: show igmp-snooping enhancements unknown-filte- ring RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 171: 11Show Igmp-Snooping Statistics Global

    Privilege Level: Guest  Format: show mac-filter-table igmp-snooping 22.6 clear Clear several items. 22.6.1 clear igmp-snooping Clear all IGMP snooping entries.  Mode: Privileged Exec Mode  Privilege Level: Operator  Format: clear igmp-snooping RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 172: 23 Interface

     Mode: Interface Range Mode  Privilege Level: Operator  Format: auto-negotiate 23.3 auto-power-down Set the auto-power-down mode on the interface.  Mode: Interface Range Mode  Privilege Level: Operator  Format: auto-power-down RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 173: Cable-Crossing

    Mode: Interface Range Mode  Privilege Level: Operator  Format: speed 23.7 name Set or remove a descriptive name for the interface.  Mode: Interface Range Mode  Privilege Level: Operator  Format: name RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 174: Power-State

    23.10 show Display device options and settings. 23.10.1 show port all Show Table with interface parameters.  Mode: command is in all modes available  Privilege Level: Guest  Format: show port all RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 175: 24 Interface Statistics

    Mode: Interface Range Mode  Privilege Level: Operator  Format: utilization alarm-threshold upper <P-1> Parameter Value Meaning 0..10000 Add alarm threshold upper value for monito- ring bandwidth utilization in hundredths of a percent. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 176: Clear

    24.3.3 show interface statistics Show summary interface statistics.  Mode: command is in all modes available  Privilege Level: Guest  Format: show interface statistics [<P-1>] Parameter Value Meaning slot no./port no. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 177: Show Interface Ether-Stats

    24.3 show 24.3.4 show interface ether-stats Show detailed interface statistics.  Mode: command is in all modes available  Privilege Level: Guest  Format: show interface ether-stats [<P-1>] Parameter Value Meaning slot no./port no. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 178: 25 Intern

    Show a list of previously run commands.  Mode: command is in all modes available  Privilege Level: Guest  Format: history 25.4 enable Turn on privileged commands.  Mode: User mode  Privilege Level: any  Format: enable RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 179: Configure

    Enter VLAN database mode.  Mode: Privileged Exec Mode  Privilege Level: Operator  Format: vlan database 25.8 exit Exit from interface mode.  Mode: Interface Range Mode  Privilege Level: Operator  Format: exit RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 180: Exit

    25.11 exit Exit from VLAN database mode.  Mode: VLAN Database Mode  Privilege Level: Operator  Format: exit 25.12 exit Exit factory mode.  Mode: any  Privilege Level: Administrator  Format: exit RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 181: 25.13 End

    [count]: Number of probes for each TTL. [maxFail]: Maximum number of consecutive probes that can fail. [size]: Size of payload in bytes. [port]: UDP destination port. Parameter Value Meaning A.B.C.D IP address. string Hostname or IP address. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 182: 25.16 Reboot

    Mode: command is in all modes available  Privilege Level: Guest  Format: ping 25.18 telnet Establish a telnet connection to a remote host.  Mode: "User Mode" and "Privileged Exec Mode"  Privilege Level: Guest  Format: telnet RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 183: 25.19 Show

    Mode: command is in all modes available  Privilege Level: Guest  Format: show reboot 25.19.2 show serviceshell Display the service shell access.  Mode: command is in all modes available  Privilege Level: Guest  Format: show serviceshell RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 184: 26 Ip Subnet Vlan

    Format: vlan association 26.2 show Display device options and settings. 26.2.1 show vlan association Display associations to VLANs.  Mode: command is in all modes available  Privilege Level: Guest  Format: show vlan association RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 185: Internet Protocol Version 4 (Ipv4)

    A.B.C.D IP address. A.B.C.D IP address. 27.2 clear Clear several items. 27.2.1 clear arp-table-switch Clear the agent's ARP table (cache).  Mode: Privileged Exec Mode  Privilege Level: Operator  Format: clear arp-table-switch RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 186: Show

    Format: show network parms 27.4 show Display device options and settings. 27.4.1 show arp Show ARP table.  Mode: command is in all modes available  Privilege Level: Guest  Format: show arp RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 187: 28 Link Backup

    [failback-time]: FailBack time in seconds for the interface pair. [description]: Description for the interface pair. Parameter Value Meaning slot no./port no. 0..3600 FailBack time interval.(default: 30) string Enter a user-defined text, max. 256 charac- ters. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 188: Link-Backup Delete

    28.3 show Display device options and settings. 28.3.1 show link-backup operation Display Link Backup global information.  Mode: command is in all modes available  Privilege Level: Guest  Format: show link-backup operation RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 189: Show Link-Backup Pairs

    Display Link Backup interface pairs.  Mode: command is in all modes available  Privilege Level: Guest  Format: show link-backup pairs [<P-1>] [<P-2>] Parameter Value Meaning slot no./port no. slot no./port no. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 190: Link Layer Discovery Protocol (Lldp)

    Enter the LLDP notification interval in seconds.  Mode: Global Config Mode  Privilege Level: Operator  Format: lldp config chassis notification-interval <P-1> Parameter Value Meaning 5..3600 Enter a number in the given range. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 191: Lldp Config Chassis Re-Init-Delay

    Mode: Global Config Mode  Privilege Level: Operator  Format: lldp config chassis tx-interval <P-1> Parameter Value Meaning 5..32768 Enter a number in the given range. 29.2 show Display device options and settings. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 192: Show Lldp Global

    Configure of Link Layer Discovery Protocol on a port. 29.3.1 lldp admin-state Configure how the interface processes LLDP frames.  Mode: Interface Range Mode  Privilege Level: Operator  Format: lldp admin-state <P-1> RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 193: Lldp Fdb-Mode

    1..50 Enter a number in the given range. 29.3.4 lldp notification Enable or disable the LLDP notification operation for interface.  Mode: Interface Range Mode  Privilege Level: Operator  Format: lldp notification RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 194: Lldp Tlv Link-Aggregation

    Mode: Interface Range Mode  Privilege Level: Operator  Format: lldp tlv max-frame-size no lldp tlv max-frame-size  Disable the option  Mode: Interface Range Mode  Privilege Level: Operator  Format: no lldp tlv max-frame-size RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 195: Lldp Tlv Mgmt-Addr

    Privilege Level: Operator  Format: no lldp tlv port-vlan 29.3.11 lldp tlv protocol Enable or disable protocol TLV transmission.  Mode: Interface Range Mode  Privilege Level: Operator  Format: lldp tlv protocol RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 196: 12Lldp Tlv Sys-Cap

    Mode: Interface Range Mode  Privilege Level: Operator  Format: lldp tlv sys-name no lldp tlv sys-name  Disable the option  Mode: Interface Range Mode  Privilege Level: Operator  Format: no lldp tlv sys-name RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 197: 15Lldp Tlv Vlan-Name

    Privilege Level: Operator  Format: no lldp tlv igmp 29.3.18 lldp tlv portsec Enable or disable portsec TLV transmission.  Mode: Interface Range Mode  Privilege Level: Operator  Format: lldp tlv portsec RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 198: 19Lldp Tlv Ptp

    Mode: Interface Range Mode  Privilege Level: Operator  Format: lldp tlv ptp no lldp tlv ptp  Disable the option  Mode: Interface Range Mode  Privilege Level: Operator  Format: no lldp tlv ptp RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 199: 30 Media Endpoint Discovery Lldp-Med

    Privilege Level: Operator  Format: no lldp med transmit-tlv capabilities 30.1.3 lldp med transmit-tlv network-policy Include/Exclude LLDP network policy TLV.  Mode: Interface Range Mode  Privilege Level: Operator  Format: lldp med transmit-tlv network-policy RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 200: Lldp

    Display the current LLDP-MED configuration on a specific port.  Mode: command is in all modes available  Privilege Level: Guest  Format: show lldp med interface [<P-1>] Parameter Value Meaning slot no./port no. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 201: Show Lldp Med Local-Device

    Display LLDP-MED summary configuration for a remote device.  Mode: command is in all modes available  Privilege Level: Guest  Format: show lldp med remote-device summary [<P-1>] Parameter Value Meaning slot no./port no. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 202: 31 Logging

    31.1.2 logging buffered severity Configure the maximum severity level to be logged to the high priority buffer.  Mode: Global Config Mode  Privilege Level: Administrator  Format: logging buffered severity <P-1> RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 203: Logging Host Add

    [type]: Configure the type of log messages to be sent to the syslog server. Parameter Value Meaning 1..8 Syslog server entry index string Hostname or IP address. a.b.c.d IP address. 1..65535 UDP port number to be used RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 204: Logging Host Delete

    [port <P-4>] [severity <P-5>] [type <P-6>] [addr]: Enter the IP address of the server. [port]: Enter the UDP port used for syslog server transmission. [severity]: Configure the maximum severity level to be sent to this syslog server. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 205: Logging Syslog Operation

    Mode: Global Config Mode  Privilege Level: Administrator  Format: logging syslog operation no logging syslog operation  Disable the option  Mode: Global Config Mode  Privilege Level: Administrator  Format: no logging syslog operation RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 206: Logging Current-Console Operation

    Normal but significant conditions. informational Informational messages. debug Debug-level messages. Same as emergency Same as alert Same as critical Same as error Same as warning Same as notice Same as informational Same as debug RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 207: Logging Console Operation

    Normal but significant conditions. informational Informational messages. debug Debug-level messages. Same as emergency Same as alert Same as critical Same as error Same as warning Same as notice Same as informational Same as debug RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 208: 11Logging Persistent Operation

    31.1.14 logging persistent severity-level Configure the maximum severity level to be logged into files.  Mode: Global Config Mode  Privilege Level: Administrator  Format: logging persistent severity-level <P-1> RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 209: Show

    Mode: command is in all modes available  Privilege Level: Guest  Format: show logging buffered [<P-1>] Parameter Value Meaning string <filter> Enter a comma separated list of se- verity ranges, numbers or enum strings are allowed. Example: 0-1,informational-debug RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 210: Show Logging Traplogs

    Display a list of logging hosts currently configured.  Mode: command is in all modes available  Privilege Level: Guest  Format: show logging host 31.3 copy Copy different kinds of items. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 211: Copy Eventlog Buffered Envm

    Copy traplog to external non-volative memory device.  Mode: Privileged Exec Mode  Privilege Level: Operator  Format: copy traplog system envm <P-1> Parameter Value Meaning string Enter a user-defined text, max. 32 charac- ters. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 212: Copy Traplog System Remote

    Enter a user-defined text, max. 128 charac- ters. 31.4 clear Clear several items. 31.4.1 clear logging buffered Clear buffered log from memory.  Mode: Privileged Exec Mode  Privilege Level: Administrator  Format: clear logging buffered RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 213: Clear Logging Persistent

    Mode: Privileged Exec Mode  Privilege Level: Administrator  Format: clear logging persistent 31.4.3 clear eventlog Clear the event log entries from memory.  Mode: Privileged Exec Mode  Privilege Level: Administrator  Format: clear eventlog RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 214: Mac Notification Operation

    Enter a number in the given range. 32.2 MAC interface commands. 32.2.1 mac notification operation Enable or disable MAC notification on this interface.  Mode: Interface Range Mode  Privilege Level: Operator  Format: mac notification operation RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 215: Show Mac Notification Global

    Format: show mac notification global 32.3.2 show mac notification interface Displays MAC notification interface information.  Mode: command is in all modes available  Privilege Level: Guest  Format: show mac notification interface RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 216: Mac Vlan

    Format: vlan association 33.2 show Display device options and settings. 33.2.1 show vlan association Display associations to VLANs.  Mode: command is in all modes available  Privilege Level: Guest  Format: show vlan association RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 217: Network Management Access Web Timeout

    Pool entry index. a.b.c.d IP address. 0..32 Prefix length netmask. enable Enable the option. disable Disable the option. enable Enable the option. disable Disable the option. enable Enable the option. disable Disable the option. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 218: Network Management Access Delete

    Disable the option. enable Enable the option. disable Disable the option. enable Enable the option. disable Disable the option. enable Enable the option. disable Disable the option. enable Enable the option. disable Disable the option. RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 219 Display device options and settings. 34.2.1 show network management access global Show global restricted management access preferences.  Mode: command is in all modes available  Privilege Level: Guest  Format: show network management access global RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 220: Show Network Management Access Rules

    Show restricted management access rules.  Mode: command is in all modes available  Privilege Level: Guest  Format: show network management access rules [<P-1>] Parameter Value Meaning 1..16 Pool entry index. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 221: Media Redundancy Protocol (Mrp)

    The device will be in the role of a ring ma- nager (MRM). 35.1.4 mrp domain modify name Configure the logical name of the MRP domain.  Mode: Global Config Mode  Privilege Level: Operator  Format: mrp domain modify name <P-1> RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 222: Mrp Domain Modify Operation

    Format: mrp domain modify port secondary <P-1> Parameter Value Meaning slot no./port no. 35.1.8 mrp domain modify recovery-delay Configure the MRM Recovery Delay.  Mode: Global Config Mode  Privilege Level: Operator  Format: mrp domain modify recovery-delay <P-1> RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 223: Mrp Domain Modify Round-Trip-Delay

    Format: mrp domain add default-domain 35.1.12 mrp domain add domain-id MRP domain ID. Format: 16 bytes in decimal notation.\n(Example: 1.2.3.4.5.6.7.8.9.10.11.12.13.14.15.16).  Mode: Global Config Mode  Privilege Level: Operator  Format: mrp domain add domain-id <P-1> RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 224: Mrp Domain Delete

    Format: no mrp operation 35.2 show Display device options and settings. 35.2.1 show mrp Show MRP settings.  Mode: command is in all modes available  Privilege Level: Guest  Format: show mrp RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 225: Mrp-Ieee Global Leave-All-Time

    PDUs. The timer is required on a per-Port, per-MRP Participant basis.  Mode: Interface Range Mode  Privilege Level: Operator  Format: mrp-ieee global leave-all-time <P-1> RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 226: Show Mrp-Ieee Global Interface

    Show the global configuration of IEEE multiple registration protocol per inter- face.  Mode: command is in all modes available  Privilege Level: Guest  Format: show mrp-ieee global interface [<P-1>] Parameter Value Meaning slot no./port no. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 227: Mrp-Ieee Mmrp Vlan-Id

    Display device options and settings. 37.2.1 show mrp-ieee mmrp global Display the IEEE MMRP global configuration.  Mode: command is in all modes available  Privilege Level: Guest  Format: show mrp-ieee mmrp global RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 228: Show Mrp-Ieee Mmrp Service-Requirement Forward-All Vlan

    Show Forward-All setting for port in given VLAN.  Mode: command is in all modes available  Privilege Level: Guest  Format: show mrp-ieee mmrp service-requirement forbidden vlan [<P-1>] Parameter Value Meaning 1..4042 Enter the VLAN ID. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 229: Mrp-Ieee Mmrp Periodic-Machine

     Format: mrp-ieee mmrp periodic-machine no mrp-ieee mmrp periodic-machine  Disable the option  Mode: Global Config Mode  Privilege Level: Operator  Format: no mrp-ieee mmrp periodic-machine 37.4 clear Clear several items. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 230: Clear Mrp-Ieee Mmrp

    Mode: Interface Range Mode  Privilege Level: Operator  Format: mrp-ieee mmrp restrict-register no mrp-ieee mmrp restrict-register  Disable the option  Mode: Interface Range Mode  Privilege Level: Operator  Format: no mrp-ieee mmrp restrict-register RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 231: Show

    Display device options and settings. 37.6.1 show mac-filter-table mmrp Display MMRP entries in the MFDB table.  Mode: command is in all modes available  Privilege Level: Guest  Format: show mac-filter-table mmrp RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 232: Mrp Ieee Mvrp

    Mode: Global Config Mode  Privilege Level: Operator  Format: mrp-ieee mvrp periodic-machine no mrp-ieee mvrp periodic-machine  Disable the option  Mode: Global Config Mode  Privilege Level: Operator  Format: no mrp-ieee mvrp periodic-machine RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 233: Mrp-Ieee

    Format: mrp-ieee mvrp restrict-register no mrp-ieee mvrp restrict-register  Disable the option  Mode: Interface Range Mode  Privilege Level: Operator  Format: no mrp-ieee mvrp restrict-register 38.3 show Display device options and settings. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 234: Show Mrp-Ieee Mvrp Global

    38.4 clear Clear several items. 38.4.1 clear mrp-ieee mvrp Clear the IEEE MVRP global and port statistic tables.  Mode: Privileged Exec Mode  Privilege Level: Operator  Format: clear mrp-ieee mvrp RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 235: 39 Port Monitor

    Configure the measure interval in seconds (5-180s) for CRC-Fragment de- tection. Default 10.  Mode: Interface Range Mode  Privilege Level: Operator  Format: port-monitor condition crc-fragments interval <P-1> Parameter Value Meaning 5..180 Enter a number in the given range. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 236: Port-Monitor Condition Crc-Fragments Count

    Configure the Link Flap counter (1-100). Default 5.  Mode: Interface Range Mode  Privilege Level: Operator  Format: port-monitor condition link-flap count <P-1> Parameter Value Meaning 1..100 Enter a number in the given range. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 237: Port-Monitor Condition Link-Flap Mode

    39.2.8 port-monitor condition overload-detection traffic- type Configure Overload detection condition traffic type  Mode: Interface Range Mode  Privilege Level: Operator  Format: port-monitor condition overload-detection traf- fic-type <P-1> Parameter Value Meaning bc-mc RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 238: Port-Monitor Condition Overload-Detection Threshold

    Configure Overload detection condition detection interval  Mode: Interface Range Mode  Privilege Level: Operator  Format: port-monitor condition overload-detection detec- tion-interval <P-1> Parameter Value Meaning 1..20 Enter a number in the given range. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 239: 13Port-Monitor Condition Overload-Detection Mode

    Privilege Level: Operator  Format: port-monitor reset no port-monitor reset  Disable the option  Mode: Interface Range Mode  Privilege Level: Operator  Format: no port-monitor reset 39.3 show Display device options and settings. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 240: Show Port-Monitor Operation

    Meaning slot no./port no. 39.3.6 show port-monitor crc-fragments Display CRC-Fragments counts for a specific interface  Mode: command is in all modes available  Privilege Level: Guest  Format: show port-monitor crc-fragments <P-1> RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 241 Port Monitor 39.3 show Parameter Value Meaning slot no./port no. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 242: 40 Port Security

    Mode: Interface Range Mode  Privilege Level: Operator  Format: port-security operation no port-security operation  Disable the option  Mode: Interface Range Mode  Privilege Level: Operator  Format: no port-security operation RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 243: Port-Security Max-Dynamic

    Remove Static MAC address from the interface.  Mode: Interface Range Mode  Privilege Level: Operator  Format: port-security mac-address delete <P-1> <P-2> Parameter Value Meaning aa:bb:cc:dd:ee:ff MAC address. 1..4042 VLAN ID RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 244: Port-Security Violation-Traps

    Display port-security (port MAC locking) information for system.  Mode: command is in all modes available  Privilege Level: Guest  Format: show port-security interface [<P-1>] Parameter Value Meaning slot no./port no. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 245: Show Port-Security Dynamic

    40.3.5 show port-security violation Display port security violation information.  Mode: command is in all modes available  Privilege Level: Guest  Format: show port-security violation <P-1> Parameter Value Meaning slot no./port no. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 246: Precision Time Protocol (Ptp)

    If the absolute value of the offset \nto the master clock is smaller than the lower bound, \nthe clock's status is set to synchronized (true).  Mode: Global Config Mode  Privilege Level: Administrator  Format: ptp sync-lower-bound <P-1> Parameter Value Meaning 1..999999999 RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 247: Ptp Sync-Upper-Bound

    Privilege Level: Administrator  Format: no ptp v2-transparent-clock syntonization 41.1.7 ptp v2-transparent-clock network-protocol Configure the network-protocol of the transparent-clock.  Mode: Global Config Mode  Privilege Level: Administrator  Format: ptp v2-transparent-clock network-protocol <P-1> RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 248: Ptp V2-Transparent-Clock Multi-Domain

    Format: no ptp v2-transparent-clock sync-local-clock 41.1.10 ptp v2-transparent-clock delay-mechanism Configure the delay mechanism of the transparent-clock.  Mode: Global Config Mode  Privilege Level: Administrator  Format: ptp v2-transparent-clock delay-mechanism <P-1> Parameter Value Meaning e2e-optimized disable RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 249: 11Ptp V2-Transparent-Clock Primary-Domain

    Enter a number in the given range. 41.1.15 ptp v2-boundary-clock priority1 Configure the priority1 value (0..255) for the BMCA  Mode: Global Config Mode  Privilege Level: Administrator  Format: ptp v2-boundary-clock priority1 <P-1> RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 250: 16Ptp V2-Boundary-Clock Priority2

     Disable the option  Mode: Global Config Mode  Privilege Level: Administrator  Format: no ptp v2-boundary-clock utc-offset-valid 41.2 Enable or disable the Precision Time Protocol (IEEE 1588-2008) on a port. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 251: Ptp V2-Transparent-Clock Operation

    Configure the Peer Delay Interval in seconds {1|2|4|8|16|32}. \nThis interval is used if delay-mechanism is set to p2p  Mode: Interface Range Mode  Privilege Level: Administrator  Format: ptp v2-transparent-clock pdelay-interval <P-1> Parameter Value Meaning RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 252: Ptp V2-Boundary-Clock Operation

    Format: ptp v2-boundary-clock pdelay-interval <P-1> Parameter Value Meaning 41.2.6 ptp v2-boundary-clock announce-interval Configure the Announce Interval in seconds {1|2|4|8|16}.  Mode: Interface Range Mode  Privilege Level: Administrator  Format: ptp v2-boundary-clock announce-interval <P-1> Parameter Value Meaning RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 253: Ptp V2-Boundary-Clock Sync-Interval

    2000000000..200000 0000 41.2.10 ptp v2-boundary-clock v1-compatibility-mode Set the PTPv1 Hardware compatibility mode {auto|on|off}.  Mode: Interface Range Mode  Privilege Level: Administrator  Format: ptp v2-boundary-clock v1-compatibility-mode <P- 1> Parameter Value Meaning auto RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 254: 11Ptp V2-Boundary-Clock Delay-Mechanism

    Mode: Interface Range Mode  Privilege Level: Administrator  Format: ptp v2-boundary-clock vlan <P-1> Parameter Value Meaning vlanId Send ptp to vlanId Use 0 for priority only tagged frames none Send all ptp packets untagged RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 255: Show

    [v2-boundary-clock]: Show PTP Boundary Clock status [v2-transparent-clock]: Show PTP Transparent Clock status [port]: Show PTP port values [v2-transparent-clock]: Show the PTP Transparent Clock port values [v2-boundary-clock]: Show the PTP Boundary Clock port values. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 256: Pwd Management

    Set minimum lower case characters for user passwords.  Mode: Global Config Mode  Privilege Level: Administrator  Format: passwords min-lowercase-chars <P-1> Parameter Value Meaning 0..16 Enter a number in the given range. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 257: Passwords Min-Numeric-Chars

    Enter a number in the given range. 42.2 show Display device options and settings. 42.2.1 show passwords Display password policies and options.  Mode: command is in all modes available  Privilege Level: Administrator  Format: show passwords RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 258: 43 Radius

    Mode: Global Config Mode  Privilege Level: Administrator  Format: radius accounting mode no radius accounting mode  Disable the option  Mode: Global Config Mode  Privilege Level: Administrator  Format: no radius accounting mode RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 259: Radius Server Attribute

    Change a RADIUS accounting server parameters.  Mode: Global Config Mode  Privilege Level: Administrator  Format: radius server acct modify <P-1> [name <P-2>] [port <P-3>] [status <P-4>] [secret [<P-5>]] [encryp- ted <P-6>] [name]: RADIUS accounting server name. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 260: Radius Server Auth Add

    43.2.7 radius server auth delete Delete a RADIUS authentication server.  Mode: Global Config Mode  Privilege Level: Administrator  Format: radius server auth delete <P-1> Parameter Value Meaning 1..8 RADIUS server index. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 261: Radius Server Auth Modify

    Configure the retransmit value for the RADIUS server.  Mode: Global Config Mode  Privilege Level: Administrator  Format: radius server retransmit <P-1> Parameter Value Meaning 1..15 Maximum number of retransmissions (default: RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 262: 10Radius Server Timeout

    Display RADIUS authentication server statistics.  Mode: command is in all modes available  Privilege Level: Guest  Format: show radius auth statistics <P-1> Parameter Value Meaning 1..8 RADIUS server index. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 263: Show Radius Acct Statistics

    Clear several items. 43.4.1 clear radius Clear the RADIUS statistics.  Mode: Privileged Exec Mode  Privilege Level: Administrator  Format: clear radius <P-1> Parameter Value Meaning statistics Clear the RADIUS statistics. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 264: Remote Monitoring (Rmon)

    1..150 Enter an index that uniquely identifies an entry in the alarm table. 44.1.3 rmon-alarm disable Disable RMON alarm.  Mode: Global Config Mode  Privilege Level: Operator  Format: rmon-alarm disable <P-1> RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 265: Rmon-Alarm Delete

    Enter the rising threshold for the sampled statistic. 1..2147483647 Enter the falling threshold for the sampled statistic. 1..2147483647 Enter the interval in seconds over which the data is sampled and compared with the rising and falling thresholds. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 266: Show

    Format: show rmon statistics [<P-1>] Parameter Value Meaning slot no./port no. 44.2.2 show rmon alarm Display configuration on RMON alarms.  Mode: command is in all modes available  Privilege Level: Guest  Format: show rmon alarm RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 267: Script File

    Format: script list system 45.1.4 script list envm list all the Script files available in the external non-volative memory device.  Mode: Privileged Exec Mode  Privilege Level: Administrator  Format: script list envm RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 268: Script Delete

    Copy Script file from file server to running-config. nvm: Copy Script file to non-volatile memory. Parameter Value Meaning string Enter a user-defined text, max. 128 charac- ters. string Enter a user-defined text, max. 32 charac- ters. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 269: Copy Script Nvm

    Enter a user-defined text, max. 32 charac- ters. 45.2.6 copy script running-config remote Copy running configuration to file server.  Mode: Privileged Exec Mode  Privilege Level: Administrator  Format: copy script running-config remote <P-1> [all] RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 270: Show

    Displays the content of the CLI Script File exist in the system.  Mode: command is in all modes available  Privilege Level: Administrator  Format: show script system <P-1> Parameter Value Meaning string Enter a user-defined text, max. 32 charac- ters. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 271: 46 Selftest

    Mode: Global Config Mode  Privilege Level: Administrator  Format: selftest ramtest no selftest ramtest  Disable the option  Mode: Global Config Mode  Privilege Level: Administrator  Format: no selftest ramtest RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 272: Selftest System-Monitor

    Display device options and settings. 46.2.1 show selftest action Displays the actions of the device takes if an error occurs.  Mode: command is in all modes available  Privilege Level: Guest  Format: show selftest action RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 273: Show Selftest Settings

    Selftest 46.2 show 46.2.2 show selftest settings Displays the selftest settings.  Mode: command is in all modes available  Privilege Level: Guest  Format: show selftest settings RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 274: Small Form-Factor Pluggable (Sfp)

    47.1.1 show sfp Show info about plugged in SFP modules  Mode: command is in all modes available  Privilege Level: Guest  Format: show sfp [<P-1>] Parameter Value Meaning slot no./port no. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 275: 48 Signal Contact

    Format: signal-contact <P-1> monitor link-failure Parameter Value Meaning signal contact no. no signal-contact monitor link-failure  Disable the option  Mode: Global Config Mode  Privilege Level: Administrator  Format: no signal-contact <P-1> monitor link-failure RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 276: Signal-Contact Monitor Envm-Not-In-Sync

    Format: no signal-contact <P-1> monitor envm-removal 48.1.5 signal-contact monitor temperature Sets the monitoring of the device temperature.  Mode: Global Config Mode  Privilege Level: Administrator  Format: signal-contact <P-1> monitor temperature Parameter Value Meaning signal contact no. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 277: Signal-Contact Monitor Ring-Redundancy

    Meaning signal contact no. 1..2 Number of power supply. no signal-contact monitor power-supply  Disable the option  Mode: Global Config Mode  Privilege Level: Administrator  Format: no signal-contact <P-1> monitor power-supply RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 278: Signal-Contact State

    Configure the signal contact interface settings. 48.2.1 signal-contact link-alarm Configure the monitoring of the specific network ports.  Mode: Interface Range Mode  Privilege Level: Administrator  Format: signal-contact <P-1> link-alarm Parameter Value Meaning signal contact no. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 279: Show

    Display the settings of the monitoring of the specific\nnetwork ports. events: Display occured device status events. all: Display all signal contact settings for the specified\nsignal contact. Parameter Value Meaning signal contact no. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 280: Switched Monitoring (Smon)

    Interface will receive and transmit frames. slot no./port no. no monitor session  Disable the option  Mode: Global Config Mode  Privilege Level: Operator  Format: no monitor session RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 281: Show

    Clear several items. 49.3.1 clear monitor session Delete configuration for this session.  Mode: Privileged Exec Mode  Privilege Level: Operator  Format: clear monitor session <P-1> Parameter Value Meaning Monitor session index. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 282: Simple Network Management Protocol (Snmp)

     Format: no snmp access version v2 50.1.3 snmp access version v3 Enable or disable SNMP version V3.  Mode: Global Config Mode  Privilege Level: Administrator  Format: snmp access version v3 RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 283: Snmp Access Port

    50.2 show Display device options and settings. 50.2.1 show snmp access Show SNMP access configuration settings.  Mode: command is in all modes available  Privilege Level: Guest  Format: show snmp access RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 284: Snmp Community

    Format: snmp community rw 51.2 show Display device options and settings. 51.2.1 show snmp community Display SNMP v1/2 community.  Mode: command is in all modes available  Privilege Level: Administrator  Format: show snmp community RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 285: Snmp Logging

    Privilege Level: Administrator  Format: no logging snmp-request get operation 52.1.2 logging snmp-request get severity Define severity level.  Mode: Global Config Mode  Privilege Level: Administrator  Format: logging snmp-request get severity <P-1> RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 286: Logging Snmp-Request Set Operation

    Privilege Level: Administrator  Format: no logging snmp-request set operation 52.1.4 logging snmp-request set severity Define severity level.  Mode: Global Config Mode  Privilege Level: Administrator  Format: logging snmp-request set severity <P-1> RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 287: Show

    52.2 show Display device options and settings. 52.2.1 show logging snmp Show the SNMP logging settings.  Mode: command is in all modes available  Privilege Level: Guest  Format: show logging snmp RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 288: Simple Network Time Protocol (Sntp)

    Set the SNTP client request interval in seconds. \nThe request-interval is only used in the operating-mode unicast.  Mode: Global Config Mode  Privilege Level: Administrator  Format: sntp client request-interval <P-1> Parameter Value Meaning 5..3600 Enter a number in the given range. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 289: Sntp Client Broadcast-Rcv-Timeout

    1..4 Enter a number in the given range. string Hostname or IP address. a.b.c.d IP address. 1..65535 Port number of SNTP Server (default 123). string Enter a user-defined text, max. 32 charac- ters. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 290: Sntp Client Server Delete

    Set the local socket port number used to listen for client requests.  Mode: Global Config Mode  Privilege Level: Administrator  Format: sntp server port <P-1> Parameter Value Meaning 1..65535 Port number of SNTP Server (default 123). RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 291: 11Sntp Server Only-If-Synchronized

    53.1.14 sntp server broadcast port Set the destination socket port number used to send\nbroadcast or multicast messages to the client.  Mode: Global Config Mode  Privilege Level: Administrator  Format: sntp server broadcast port <P-1> RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 292: 15Sntp Server Broadcast Interval

    Privilege Level: Guest  Format: show sntp global 53.2.2 show sntp client status Show SNTP client status.  Mode: command is in all modes available  Privilege Level: Guest  Format: show sntp client status RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 293: Show Sntp Client Server

    Format: show sntp server status 53.2.5 show sntp server broadcast Show SNTP server broadcast configuration parameters.  Mode: command is in all modes available  Privilege Level: Guest  Format: show sntp server broadcast RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 294: 54 Spanning Tree

     Privilege Level: Operator  Format: no spanning-tree bpdu-filter 54.1.3 spanning-tree bpdu-guard Enable or disable BPDU guard on edge ports.  Mode: Global Config Mode  Privilege Level: Operator  Format: spanning-tree bpdu-guard RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 295: Spanning-Tree Bpdu-Migration-Check

    Set the Hello Time parameter [s].  Mode: Global Config Mode  Privilege Level: Operator  Format: spanning-tree hello-time <P-1> Parameter Value Meaning 1..2 Set the Hello Time parameter (unit: se- conds). RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 296: Spanning-Tree Hold-Count

    CIST and RSTP). 0..4094 Select the MST bridge VLAN. 54.1.12 spanning-tree configuration name Set MST configuration name.  Mode: Global Config Mode  Privilege Level: Operator  Format: spanning-tree configuration name <P-1> RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 297: 13Spanning-Tree Configuration Revision

    Mode: Interface Range Mode  Privilege Level: Operator  Format: spanning-tree bpdu-flood no spanning-tree bpdu-flood  Disable the option  Mode: Interface Range Mode  Privilege Level: Operator  Format: no spanning-tree bpdu-flood RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 298: Spanning-Tree Edge-Auto

    Privilege Level: Operator  Format: no spanning-tree guard-loop 54.2.6 spanning-tree guard-root Enable or disable the root guard on a port.  Mode: Interface Range Mode  Privilege Level: Operator  Format: spanning-tree guard-root RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 299: Spanning-Tree Guard-Tcn

    Specify the port priority.  Mode: Interface Range Mode  Privilege Level: Operator  Format: spanning-tree priority <P-1> Parameter Value Meaning 0..240 Specify the port priority. 54.3 show Display device options and settings. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 300: Show Spanning-Tree Global

    Spanning Tree information and settings for an interface.  Mode: command is in all modes available  Privilege Level: Guest  Format: show spanning-tree port <P-1> Parameter Value Meaning slot no./port no. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 301: Secure Shell (Ssh)

    Set the SSH port number (default: 22).  Mode: Global Config Mode  Privilege Level: Administrator  Format: ssh port <P-1> Parameter Value Meaning 1..65535 Port number of the SSH server (default: 22). RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 302: Ssh Max-Sessions

    Copy SSH key from server.  Mode: Privileged Exec Mode  Privilege Level: Administrator  Format: copy sshkey remote <P-1> nvm nvm: Copy SSH key from server to NV memory. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 303: Copy Sshkey Envm

    Enter a user-defined text, max. 128 charac- ters. 55.3 show Display device options and settings. 55.3.1 show ssh Show SSH server information.  Mode: command is in all modes available  Privilege Level: Guest  Format: show ssh RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 304: 56 Storm Control

    Traffic shape commands. 56.2.1 traffic-shape bw Set threshold value  Mode: Interface Range Mode  Privilege Level: Operator  Format: traffic-shape bw <P-1> Parameter Value Meaning 0..100 Enter a number in the given range. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 305: Mtu

    Mode: Interface Range Mode  Privilege Level: Operator  Format: no storm-control flow-control 56.5.2 storm-control ingress unit Set unit.  Mode: Interface Range Mode  Privilege Level: Operator  Format: storm-control ingress unit <P-1> RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 306: Storm-Control Ingress Unicast Operation

    Privilege Level: Operator  Format: storm-control ingress broadcast operation no storm-control ingress broadcast operation  Disable the option  Mode: Interface Range Mode  Privilege Level: Operator  Format: no storm-control ingress broadcast operation RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 307: Show

    Mode: command is in all modes available  Privilege Level: Guest  Format: show traffic-shape 56.6.4 show mtu Show mtu Parameters.  Mode: command is in all modes available  Privilege Level: Guest  Format: show mtu RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 308: 57 System

    Enter a user-defined text, max. 255 charac- ters. 57.1.4 system pre-login-banner operation Enable or disable the pre-login banner.  Mode: Global Config Mode  Privilege Level: Administrator  Format: system pre-login-banner operation RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 309: System Pre-Login-Banner Text

    Upper temperature threshold ([°C], default 70). 57.2.2 temperature lower-limit Configure the lower temperature limit.  Mode: Global Config Mode  Privilege Level: Administrator  Format: temperature lower-limit <P-1> Parameter Value Meaning -99..99 Lower temperature threshold ([°C], default RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 310: Show

     Format: show system temperature limits 57.3.6 show system temperature extremes Minimal and maximal temperature  Mode: command is in all modes available  Privilege Level: Guest  Format: show system temperature extremes RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 311: Show System Temperature Histogram

    System 57.3 show 57.3.7 show system temperature histogram Temperature histogram  Mode: command is in all modes available  Privilege Level: Guest  Format: show system temperature histogram RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 312: 58 Telnet

    Set the listening port for the telnet server.  Mode: Global Config Mode  Privilege Level: Administrator  Format: telnet port <P-1> Parameter Value Meaning 1..65535 Set the listening port for the telnet ser- ver. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 313: Telnet Max-Sessions

    58.2 show Display device options and settings. 58.2.1 show telnet Show telnet server information.  Mode: command is in all modes available  Privilege Level: Guest  Format: show telnet RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 314: 59 Traps

    Mode: Global Config Mode  Privilege Level: Administrator  Format: snmp trap add <P-1> <P-2> Parameter Value Meaning string <name> Trap name (1 to 32 characters) a.b.c.d a.b.c.d Single IP address. a.b.c.d:n a.b.c.d:n Address with port. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 315: Show

    59.2 show 59.2 show Display device options and settings. 59.2.1 show snmp traps Display SNMP traps.  Mode: command is in all modes available  Privilege Level: Guest  Format: show snmp traps RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 316: 60 Users

    <user> User name (up to 32 characters). 60.1.4 users disable Disable user.  Mode: Global Config Mode  Privilege Level: Administrator  Format: users disable <P-1> Parameter Value Meaning string <user> User name (up to 32 characters). RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 317: Users Password

    Specify snmpv3 access role for a user.  Mode: Global Config Mode  Privilege Level: Administrator  Format: users access-role <P-1> <P-2> Parameter Value Meaning string <user> User name (up to 32 characters). RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 318: Users Lock-Status

    Disable the option. 60.2 show Display device options and settings. 60.2.1 show users Display users and user accounts information.  Mode: command is in all modes available  Privilege Level: Administrator  Format: show users RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 319: Virtual Lan (Vlan)

    VLAN ID for this port. vlanonly Only frames received with a VLAN tag will be forwarded. All other frames will be dropped. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 320: Vlan Ingressfilter

    Format: vlan tagging <P-1> Parameter Value Meaning 1..4042 Enter the VLAN ID. no vlan tagging  Disable the option  Mode: Interface Range Mode  Privilege Level: Operator  Format: no vlan tagging RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 321: Vlan Participation Include

    Creation and configuration of VLANS. 61.4.1 vlan add Create a VLAN  Mode: VLAN Database Mode  Privilege Level: Operator  Format: vlan add <P-1> Parameter Value Meaning 1..4042 Enter the VLAN ID. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 322: Vlan Delete

    Show VLAN configuration of a single port.  Mode: command is in all modes available  Privilege Level: Guest  Format: show vlan port [<P-1>] Parameter Value Meaning slot no./port no. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 323: Show Vlan Member Current

    Enter a number in the given range. 61.6.3 network management priority ip-dscp Configure the management VLAN ip-dscp priority of the switch.  Mode: Privileged Exec Mode  Privilege Level: Operator  Format: network management priority ip-dscp <P-1> RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 324 Virtual LAN (VLAN) 61.6 network Parameter Value Meaning 0..63 Enter a number in the given range. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 325: 62 Voice Vlan

    Format: voice vlan vlan-id <P-1> [dot1p <P-2>] [dot1p]: Set and configure the vlan id and dot1p interface mode. Parameter Value Meaning 0..4042 Enter the VLAN ID. Entering of ID 0 disables the feature. RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 326: Voice Vlan Dot1P

    Privilege Level: Operator  Format: voice vlan none 62.2.4 voice vlan untagged Configure the untagged voice VLAN interface mode.  Mode: Interface Range Mode  Privilege Level: Operator  Format: voice vlan untagged RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 327: Voice Vlan Disable

    Display device options and settings. 62.3.1 show voice vlan global Display the current global Voice VLAN admin mode.  Mode: command is in all modes available  Privilege Level: Guest  Format: show voice vlan global RM CLI HiOS-2S RSPS Release 3.0 01/2014...

  • Seite 328: Show Voice Vlan Interface

    Display a summary of the current Voice VLAN configuration for a specific port or for all ports.  Mode: command is in all modes available  Privilege Level: Guest  Format: show voice vlan interface [<P-1>] Parameter Value Meaning slot no./port no. RM CLI HiOS-2S RSPS Release 3.0 01/2014...
  • Seite 329 Voice VLAN 62.3 show RM CLI HiOS-2S RSPS Release 3.0 01/2014...

Inhaltsverzeichnis