DeWalt XR LI-ION DCG405 Bersetzt Von Den Originalanweisungen Seite 32

EnGLIsh
CORDLESS SMALL ANGLE GRINDER
DCG405
Congratulations!
You have chosen a D WALT tool. Years of experience, thorough
e
product development and innovation make D
most reliable partners for professional power tool users.
Technical Data
Voltage
Type
Battery type
Power output
No-load speed
Grinding wheel diameter
Grinding wheel thickness (max)
Cutting off wheel diameter
Cutting off wheel thickness (max)
Wire wheel diameter
Wire wheel thickness (max)
Spindle diameter
Spindle length
Weight (without battery pack)
Noise values and vibration values (triax vector sum) according to EN62841-2-3
L (emission sound pressure level)
PA
L (sound power level)
WA
K (uncertainty for the given sound level)
Surface grinding
Vibration emission value a =
h,AG
Uncertainty K =
Disc sanding
Vibration emission value a =
h,DS
Uncertainty K =
Concrete grinding and cutting off
Vibration emission value a
h,CG
Uncertainty K =
The vibration emission level given in this information sheet has
been measured in accordance with a standardised test given in
EN62841 and may be used to compare one tool with another. It
may be used for a preliminary assessment of exposure.

WARNING: The declared vibration emission level
represents the main applications of the tool. However if the
tool is used for different applications, with different accessories
or poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or when
32
WALT one of the
e
DCG405
V
DC
Li-Ion
W
min -1 9000
mm
mm
mm
mm
mm
mm
mm
kg
dB(A)
dB(A)
dB(A)
m/s 2
m/s 2
m/s 2 <2.5
m/s 2
= m/s 2
m/s 2
it is running but not actually doing the job. This may significantly
reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.

CAUTION: Working with the wire brush or the abrasive
cutting can lead to different vibration levels.
18

WARNING : Grinding thin sheets of metal or other easily
2
vibrating structures with a large surface can result in a total noise
emission much higher (up to 15 dB) than the declared noise
emission values. Such workpieces should as far as possible be
800
prevented from emitting sound by suitable measures such as the
application of heavy flexible damping mats. The increased noise
emission is also to be considered for both the risk assessment of
125
noise exposure and selecting adequate hearing protection.
6.4
EC-Declaration of Conformity
125
Machinery Directive
3
115
13
Cordless Small Angle Grinder
M14
DCG405
21.5
D WALT declares that these products described under
1.74 e
Technical Data are in compliance with:
2006/42/EC, EN62841-1:2015 +A11:2022, EN IEC 62841-2-
3:2021 +A11:2021.
85
These products also comply with Directive 2014/30/EU and
2011/65/EU. For more information, please contact D
93
the following address or refer to the back of the manual.
3
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of D
5.8
1.5
Markus Rompel
Director Engineering
1.5
D WALT, Richard-Klinger-Strasse 11,
e
65510, Idstein, Germany
13.12.2023
4.8
1.5
THE SUPPLY OF MACHINERY (SAFETY) REGULATIONS
D WALT declares that these products described under
e
"technical data" are in compliance with:
The Supply of Machinery (Safety) Regulations, 2008, S.I.
2008/1597 (as amended),
EN62841-1:2015 +A11:2022, EN IEC 62841-2-3:2021 +A11:2021.
DECLARATION OF CONFORMITY
2008
Cordless Small Angle Grinder
DCG405
WALT at
e
WALT.
e