Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Table 2: Bytes 0-1: Performance diagnosis
Byte
Bit
Meaning
0
0
UA
1
UL UV < 18 V
2
UL OV > 26.4 V
3
HWE
4
Reserved
5
Reserved
6
Reserved
7
Reserved
Table 3: Bytes 3-8: Open load diagnosis
Byte
Bit
Open load at
Valve
Valve coil
3
0
1
14
1
12
2
2
14
3
12
4
3
14
5
12
6
4
14
7
12
Table 4: Bytes 9-14: Short circuit diagnosis
Byte
Bit
Short circuit at
Valve
Valve coil
9
0
1
14
1
12
2
2
14
3
12
4
3
14
5
12
6
4
14
7
12
Diagnosis mask for valve outputs
Table 5: Assignment of the bits to the output positions
Byte
Bit
Output position
Valve posi-
tion
0
0
1
1
2
2
3
4
3
5
6
4
7
2
0
9
1
2
10
3
4
11
5
6
12
7
4
0
17
1
2
18
3
4
19
5
6
20
7
AVENTICS™ Ethernet/IP | 570090-BAL-AB | English
Byte
Bit
1
0
1
2
3
4
5
6
7
...
Byte
Bit
Open load at
Valve
...
8
0
21
...
1
...
2
22
...
3
...
4
23
...
5
...
6
24
...
7
...
Byte
Bit
Short circuit at
Valve
...
14
0
21
...
1
...
2
22
...
3
...
4
23
...
5
...
6
24
...
7
Byte
Bit
Output position
Valve
Valve posi-
coil
tion
14
1
0
5
12
1
14
2
6
12
3
14
4
7
12
5
14
6
8
12
7
14
3
0
13
12
1
14
2
14
12
3
14
4
15
12
5
14
6
16
12
7
14
5
0
21
12
1
14
2
22
12
3
14
4
23
12
5
14
6
24
12
7
Activate diagnosis mask for valve outputs:
Adjust the value 0 at the desired output position.
u
Meaning
Deactivate diagnosis mask for valve outputs (default setting):
Reserved
Adjust the value 1 at the desired output position.
u
Reserved
Reserved
Parameters for the behavior in the event of an interruption in
Reserved
communication
Reserved
Fail safe modes
Reserved
Fail safe disabled
Reserved
Output last data received
Reserved
Output Fail safe data
Transferring configuration to the PLC
1. Ensure that the parameter settings of the PLC are compatible with those of
Valve coil
the valve system.
14
2. Establish connection to the PLC.
12
3. Transfer valve system data to the PLC. See the PLC documentation.
14
4. Set COMM Fault/Idle mode via the PLC.
12
14
7.1.2 Configuring the network
12
Preparation
14
1. Give the product a distinct name in the PLC configuration program.
12
2. Configure the product in the PLC configuration program as slave in the field-
bus system.
Procedure
Valve coil
Via Ethernet/IP function
14
1. Select product.
12
2. Set the IP address.
14
12
7.1.3 Assigning IP address and subnet mask
14
Via SPS/DHCP server
12
1. Adjust value 0 on SW1 and SW2.
14
2. Set the address via the PLC or DHCP/BOOTP server.
12
Via DIP switch
Table 6: Standard settings for IP address
Setting
IP address
Valve
Subnet mask
coil
Gateway IP address
14
12
1. Release product. See Conversion and extension.
14
2. Adjust the address on switches SW1 and SW2.
12
3. Mounting the product See Conversion and extension.
14
Table 7: Compilation of the IP address for manual setting
12
Octet
14
1
12
14
2
12
3
14
4
12
14
SW1 position 2 is not connected.
12
14
Table 8: Setting the 4th octet via SW2
12
Value of the 4th
octet
14
12
DHCP/BOOTP
14
mode
12
1
14
2
12
3
14
...
12
254
Behavior of the product
Switch off all outputs (default setting)
Maintain all outputs
User-defined data
Value
192.168.0.120
255.255.255.0
192.168.0.1
Range
192
168
0 ... 1
0 ... 255
SW2 positions
1
2
3
4
0
0
0
0
1
0
0
0
0
1
0
0
1
1
0
0
...
...
...
...
0
1
1
1
Setting option
Default value
Default value
SW1, position 1
Default value: 0
SW2, position 1 ... 8, binary
Default value: 0
5
6
7
8
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
...
...
...
...
1
1
1
1
18
Werbung
