Miller XMT 350 CC/CV Auto-Line Betriebsanleitung Seite 14

= < 60
= < 60
Use coolant suggested by the manufacturer.
Use coolant suggested by the manufacturer.
Falling unit can cause injury. Do not move or operate unit where it could tip.
Falling unit can cause injury. Do not move or operate unit where it could tip.
OM-2254 Seite 8
�
Eine komplette Ersatzteilliste ist unter www.MillerWelds.com verfügbar.
after power is turned off before working on unit, AND check input ca-
pacitor voltage, and be sure it is near 0 before touching any parts.
Hazardous voltage remains on input capacitors after power is turned
Nach dem Abschalten des Stroms ist immer noch eine gefährliche
off. Do not touch fully charged capacitors. Always wait
Spannung an den Eingangskondensatoren vorhanden. Voll aufgela- Hazardous voltage remains on input capacitors after power is turned
after power is turned off before working on unit, AND check input ca-
dene Kondensatoren nicht berühren. Vor dem Arbeiten am Gerät im- off. Do not touch fully charged capacitors. Always wait
pacitor voltage, and be sure it is near 0 before touching any parts.
mer mindestens 5 Minuten nach dem Stromabschalten warten UND
power is turned off before working on unit, AND check input capacitor
prüfen Sie die Spannung des Eingangskondensators und stellen Sie voltage, and be sure it is near 0 before touching any parts.
sicher, dass sie gegen 0 geht, bevor Teile berührt werden.
Hazardous voltage remains on input capacitors after power is turned
Always lift and support unit using both handles. Keep angle of lifting
off. Do not touch fully charged capacitors. Always wait
Stets beide Griffe zum Hochheben des Gerätes verwenden. Der Win- device less than 60 degrees.
power is turned off before working on unit, AND check input capacitor
kel der Hebevorrichtung darf nicht größer als 60 Grad sein. Gerät nur
Use a proper cart to move unit.
voltage, and be sure it is near 0 before touching any parts.
auf einem geeigneten Wagen transportieren.
Always lift and support unit using both handles. Keep angle of lifting
device less than 60 degrees.
Engine fuel plus flames or sparks can cause fire.
Use a proper cart to move unit.
Engine fuel plus flames or sparks can cause fire.
Remove unit from shipping crate. Remove Owner's Manual from unit.
Follow instructions to install muffler.
Remove unit from shipping crate. Remove Owner's Manual from unit.
Follow instructions to install muffler.
Read Owner's Manual. Read labels on unit.
Move jumper links as shown on inside label to match input voltage at
Read Owner's Manual. Read labels on unit.
job site. Include extra length in grounding conductor and connect
grounding conductor first. Connect line input conductors as shown on
inside label. Double-check all connections, jumper link positions, and
input voltage before applying power.
Move jumper links as shown on inside label to match input voltage at
job site. Include extra length in grounding conductor and connect
grounding conductor first. Connect line input conductors as shown on
inside label. Double-check all connections, jumper link positions, and
Plugged filter or hoses can cause overheating to the power source
input voltage before applying power.
and torch.
Plugged filter or hoses can cause overheating to the power source
and torch.
Every 100 hours, check and clean filter and check condition of hoses.
Every 100 hours, check and clean filter and check condition of hoses.
Safe42 2017 04
60 seconds
5 minutes after
Safe42 2017 04
Safe43 2017 04
5 minutes after
Safe43 2017 04
Safe44 2012 05
Safe44 2012 05
Safe45 2012 05
Safe45 2012 05
Safe46 2012 05
Safe46 2012 05
Safe47 2012 05
Safe47 2012 05
Safe49 2012 05
Safe49 2012 05
Safe50 2012 05
Safe50 2012 05
Safe51 2012 05
Safe51 2012 05
Safe52 2012 05
Safe52 2012 05
Safe53 2017 04
OM-
Safe53 2017 04
OM-