Scheppach BTS800Vario Originalbetriebsanleitung Seite 26

Notes on the electrical and electronic equipment act
[ElektroG]
Waste electrical and electronic equipment
does not belong in household waste, but must
be collected and disposed of separately!
• Used batteries or rechargeable batteries that are not
installed permanently in the old appliance must be re-
moved non-destructively before disposal! Their dis-
posal is regulated by the battery act.
• Owners or users of electrical and electronic devices
are legally obliged to return them after use.
• The end user is responsible for deleting their personal
data from the old device being disposed of!
• The symbol of the crossed-out dustbin means that
waste electrical and electronic equipment must not be
disposed of with household waste.
• Waste electrical and electronic equipment can be
handed in free of charge at the following places:
– Public disposal or collection points (e.g. municipal
works yards)
18 Troubleshooting
Fault
Engine does not start
The product becomes
slower during work
Grinding belt comes off
the drive pulleys.
Wood gets burnt during
sanding.
19 EU Declaration of Conformity
Original Declaration of Conformity
Manufacturer:
Scheppach GmbH
Günzburger Straße 69
D-89335 Ichenhausen
We declare under our sole responsibility that the product
described here complies with the applicable directives
and standards.
Brand: SCHEPPACH
Art. designation: BELT AND DISC SANDER
BTS800Vario
Item No. 5903313901
EU directives:
2014/30/EU, 2006/42/EC, 2011/65/EU*
* The object of the declaration described above fulfils the
regulations of the directive 2011/65/EU of the European
Parliament and Council from 8th June 2011, on the re-
striction of the use of certain hazardous substances in
electrical and electronic equipment.
26 | GB
Possible cause
On/off switch damaged
On/off cable damaged
On/off relay damaged
Too much pressure is applied to
the workpiece.
It does not run straight.
Sanding disc or belt is covered
with grease.
Excessive pressure was applied
to the workpiece.
www.scheppach.com
– Points of sale of electrical appliances (stationary
and online), provided that dealers are obliged to
take them back or offer to do so voluntarily.
– Up to three waste electrical devices per type of de-
vice, with an edge length of no more than 25 centi-
metres, can be returned free of charge to the man-
ufacturer without prior purchase of a new device
from the manufacturer or taken to another autho-
rised collection point in your vicinity.
– Further supplementary take-back conditions of the
manufacturers and distributors can be obtained
from the respective customer service.
• If the manufacturer delivers a new electrical appliance
to a private household, the manufacturer can arrange
for the free collection of the old electrical appliance
upon request from the end user. Please contact the
manufacturer's customer service for this.
• These statements only apply to devices installed and
sold in the countries of the European Union and which
are subject to the European Directive 2012/19/EU. In
countries outside the European Union, different regu-
lations may apply to the disposal of waste electrical
and electronic equipment.
Remedy
Replace all damaged parts before you use your sander
again. Contact your local service centre or an authorised
service station. Every attempt to carry out a repair, can be
dangerous if it is not done by skilled personnel.
Apply less pressure to the workpiece.
Reset the track.
Replace grinding belt or sanding disc.
Reduce the pressure applied to the workpiece.
Applied standards:
EN 62841-1:2015/A11:2022; EN ISO 12100:2010;
EN IEC 55014-1:2021; EN IEC 55014-2:2021;
EN IEC 61000-3-2:2019/A1:2021;
EN 61000-3-3:2013/A2:2021
Documentation authorised representative:
Georg Kohler
Günzburger Str. 69
D-89335 Ichenhausen
Ichenhausen, 07.11.2023
Simon Schunk
Division Manager Product Center
Andreas Pecher
Head of Project Management